Bebe Stars KBH310 Car Seats User Manual

: June 13, 2024
: Bebe Stars

Table of Contents

Bebe Stars KBH310 Car Seats
SAFETY INSTRUCTIONS
PARTS
INSTALLATION
INSTRUCTIONS FOR USE
CARE & MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Bebe Stars KBH310 Car Seats

Bebe-Stars-KBH310-Car-Seats-product-img

SAFETY INSTRUCTIONS

Thank you for purchasing this booster car seat by Bebe Stars. We will always give you the best products and services!

Please read this instruction manual carefully before you use it!

This booster car seat is suitable for children with a height of 135-150 cm.
We strongly advise you not to use an unlicensed or modified or without the manufacturer’s instruction product, it is very dangerous. We, also, advise you strongly not to use a second-hand product, because you are not sure what has happened to it.
The straps holding the restraint to the vehicle should be tight, any straps restraining the child should be adjusted to the child’s body and should not be twisted.
Make sure the lap belt is stretched as low as possible over the child’s hips.
DO NOT use any load-bearing force points other than those described in the instructions and marked in the child restraint.
For the future use of the seat, it is important that you keep the instruction manual carefully. If in doubt, please contact the manufacturer.
It can be installed with an ISOFIX system or with a 3-point safety belt. It is approved to ECE 129R03/04.
NEVER leave your child unattended in a car even for a short time.
DO NOT use a child safety seat that has been in a crash. A crash can cause damage to the child safety seat that you can not see.
DO NOT modify or attempt to modify the child safety seat in any way.
DO NOT take apart or attempt to take apart this child’s safety seat etc.
DO NOT use a child safety seat with damaged or missing parts.
DO NOT change the cover or harness, they are important components.
Make sure the vehicle belt is tightly secured and the car seat is correctly installed each time you use it.
Car interiors can become very hot when in direct sunlight, it is recommended that you should cover the car seat when not in use. This prevents some components from becoming hot and burns the child.
Make sure that all luggage and objects likely to cause injury in the event of an accident are properly secured.
Make sure the seat is in a safe position. Do not put any sharp or hard items around the seat.

PARTS

Guide groove for the lap belt
Cushion with soft cover
Connector
Belt
Belt guide
Isofix system

Bebe-Stars-KBH310-Car-Seats-fig-1

INSTALLATION

ISOFIX 1.1 + 3-POINT SAFETY BELT

Bebe-Stars-KBH310-Car-Seats-fig-2 Bebe-Stars-
KBH310-Car-Seats-fig-3 Bebe-Stars-KBH310-Car-Seats-
fig-4

3-POINT SAFETY BELT

Bebe-Stars-KBH310-Car-Seats-fig-5 Bebe-Stars-
KBH310-Car-Seats-fig-6

ISOFIX + 3-POINT SAFETY BELT INSTALLATION

Find the ISOFIX anchorage points on the car and clip the two guide sleeves to the two ISOFIX anchorage points of the car. Press and hold the ISOFIX unlock button while sliding outwards to adjust the ISOFIX connectors on both sides of the anchorage seat to the longest state. Connect the ISOFIX connector to the ISOFIX anchorage point of the car until you hear a “click” sound. Ensure that the belt is accessible and not trapped behind the booster.
Place the child on the booster seat and adjust the length of the belt according to the child’s height. Pull out the 3-point safety car belt, the diagonal belt passes through the guide groove and the top of the armrest, the lap belt passes through the guide grooves on both sides of the booster and is fixed to the car buckle until you hear a “click” sound to ensure that the buckle is firmly locked. Fasten the car belt and pull the diagonal section tight so that there is no slack left in the seat belt.
Guide the belt guide (with the belt) to the child’s shoulder on the side of the car belt automatic retractor device. The belt of the belt guide system lies in the middle of the shoulder. Don’t place it too close to the neck and shoulder side edge, you must adjust the connector of the belt to adjust the length of the belt and the height of the belt guide.
POINT SAFETY BELT INSTALLATION
Ensure that the ISOFIX connector is retracted into the base and place the safety seat on the rear row. Place the child on the booster seat and adjust the length of the belt according to the child’s height. Pull out the 3-point safety car belt, the diagonal belt passes through the guide groove and the top of the armrest, the lap belt passes through the guide grooves on both sides of the booster and is fixed to the car buckle until you hear a “click” sound to ensure that the buckle is firmly locked. Fasten the car belt and pull the diagonal section tight so that there is no slack left in the seat belt.
Guide the belt guide (with the belt) to the child’s shoulder on the side of the car belt automatic retractor device. The belt of the belt guide system lies in the middle of the shoulder. Don’t place it too close to the neck and shoulder side edge, you must adjust the connector of the belt to adjust the length of the belt and the height of the belt guide.

INSTRUCTIONS FOR USE

Install the position of the child seat in the vehicle.
How to detach the safety seat with ISOFIX from the vehicle.

Bebe-Stars-KBH310-Car-Seats-fig-8

Install the position of the child seat in the vehicle

Unable to install on this position You can install on this position
Do not use it on front passenger seats with a front airbag!
Only use with a 3-point belt.

Diagonal belt.
Lap belt.

We do not recommend installing the child safety seat in the front passenger seat.
DO NOT use a child safety seat if the vehicle seat is equipped with front airbags, it can be dangerous. This does not apply to so-called side airbags.
DO NOT use a 2-point belt. Please install with the 3-point belt.
ONLY use for Forward Facing.
How to detach the safety seat with ISOFIX from the vehicle

Press and hold the ISOFIX unlock buttons on both sides at the same time. At this time, the ISOFIX lock indicator turns red, which means it is unlocked.
Pull the booster outwards and remove it from the vehicle.

CARE & MAINTENANCE

Periodically inspect the booster for worn or damaged parts. If damaged parts are found, replace the child seat. The booster must be replaced after an accident.
Keep the child’s seat clean. Do not lubricate any parts of the booster.
To prolong the life of the booster, keep it clean and do not leave it in direct sunlight for extended periods of time. Please keep this booster in a dry and ventilated place to avoid damp mold.

Cleaning the belt and shell

In case they become dusty, wipe them with a damp sponge and let them dry naturally; do not use any other cleaning agents.
In case of light soiling, rinse it gently with warm water and let it dry naturally.

Storage

When not in use, store in a safe, dry place and away from heat and direct sunlight.
Avoid placing heavy objects on top of the seat.

Remove the fabric cover
You can remove fabric covers from the seat and hand wash them with mild detergent and warm water. Allow it to dry fully, preferably away from direct sunlight.