READYLIFT 77-23200 Dual Steering Stabilizer Instruction Manual
- June 13, 2024
- READYLIFT
Table of Contents
77-23200 2023 F250/350 Dual Steering Stabilizer
IF your ReadyLIFT® product has a damaged or missing part, please contact
customer service directly and a new replacement part will be sent to you
immediately.
For warranty issues, please return to the place of installation and contact
ReadyLIFT.
877-759-9991
MON-FRI 7AM-4PM PST
OR
EMAIL: support@readylift-ami.COM
WEBSITE: ReadyLIFT.COM
Please retain this document in your vehicle at all times.
Limited Lifetime Warranty
This unique product warranty proves our commitment to the quality and
reliability of every product that ReadyLIFT manufactures. The ReadyLIFT
product warranty only extends to the original purchaser of any ReadyLIFT
product, if it breaks, we will give you a new part. Warranty does not apply to
discontinued parts.
Our Limited Lifetime Warranty excludes the following ReadyLIFT items;
bushings, bump stops, ball joints, tie rod ends, heim joints and shock
absorbers. These parts are subject to wear and are not considered defective
when worn. They are warranted for 12 months from the date of purchase for
defects in workmanship. This product warranty is voided if the vehicle is not
aligned after kit installation and proper maintenance is routinely done.
Product purchased directly from ReadyLIFT has a 90 day return policy on
uninstalled products from the date of purchase (may be subject to restocking
fee). Uninstalled product returns must be in the original ReadyLIFT packaging.
Please call 877-759-9991 to get an RGA#
for any return. Customer is responsible for shipping costs back to ReadyLIFT.
Returns without RGA# will be refused. Contact ReadyLIFT directly about any
potentially defective parts prior to removal from vehicle.
ReadyLIFT products are NOT intended for off-road abuse. Any damage or failure
as a result from off-road abuse voids the warranty of the ReadyLIFT product.
ReadyLIFT is NOT responsible for any subsequent damages to any related vehicle
parts due to misuse, abuse, improper installation, or lack of maintenance.
Furthermore, ReadyLIFT reserves the right to change, modify or cancel this
warranty without prior notice.
WARNING
READ INSTRUCTIONS THOROUGHLY AND COMPLETELY BEFORE BEGINNING INSTALLATION.
INSTALLATION BY A CERTIFIED PROFESSIONAL MECHANIC IS HIGHLY RECOMMENDED.
READYLIFT® IS NOT RESPONSIBLE FOR ANY DAMAGE OR FAILURE RESULTING FROM
IMPROPER INSTALLATION.
Safety Warning
MISUSE OF THIS PRODUCT COULD LEAD TO INJURY OR DEATH.
Suspension systems or components that enhance the on and off-road performance
of your vehicle may cause it to handle differently than it did from the
factory. Extreme care must be used to prevent loss of control or vehicle
rollover during abrupt maneuvers.
Always operate your vehicle at reduced speeds to ensure your ability to
control your vehicle under all driving conditions. Failure to drive safely may
result in serious injury or death to driver and passengers.
Driver and passengers must ALWAYS wear your seat belts, avoid quick sharp
turns and other sudden maneuvers. ReadyLIFT Suspension does not recommend the
combined use of suspension lifts, body lifts, or other lifting devices.
You should never operate your vehicle under the influence of alcohol or drugs.
Constant maintenance is required to keep your vehicle safe. Thoroughly inspect
your vehicle before and after every off-road use.
It is the responsibility of the retailer and/or the installer to review all
state and local laws, with the end user of this product, related to bumper
height laws and the lifting of their vehicle before the purchase and
installation of any ReadyLIFT products.
It is the responsibility of the driver/s to check their surrounding area for
obstructions, people, and animals before moving the vehicle.
All raised vehicles have increased blind spots; damage, injury and/or death
can occur if these instructions are not followed.
Installation Warning
All steps and procedures described in these instructions were performed while
the vehicle was properly supported on a two post vehicle lift with safety
jacks.
Use caution during all disassembly and assembly steps to insure suspension
components are not over extended causing damage to any vehicle components and
parts included in this kit. Included instructions are guidelines only for
recommended procedures and are not meant to be definitive. Installer is
responsible to insure a safe and controllable vehicle after performing
modifications.
ReadyLIFT Suspension recommends the use of an OE Service Manual for model/year
of vehicle when disassembly and assembly of factory and related components.
Unless otherwise specified, tighten all bolts and fasteners to standard torque
specifications listed within the OE Service Manual.
Suspension components that use rubber or urethane bushings should be tightened
with the vehicle at normal ride height. This will prevent premature wear or
failure of the bushing and maintain ride comfort.
Larger tire and wheel combinations may increase leverage on suspension,
steering, and related components.
Due to payload options and initial ride height variances, the amount of lift
is a base figure. Final ride height dimensions may vary in accordance to
original vehicle ride height. Always measure the vehicle ride height prior to
beginning installation.
BILL OF MATERIALS
COMPONENTS|
---|---
DESCRIPTION| QTY
MAIN BODY STABILIZER BRACKET| 1
REAR AXLE BRACKET| 1
TIE ROD BRACKET DRIVER| 1
TIE ROD BRACKET PASSENGER| 1
STABILIZER TOP PLATE| 1
STEERING STABILIZER| 2
HARDWARE|
---|---
DESCRIPTION| QTY
05-22 Diff. Mount, Dual Steering Stabilizer|
3/8″-16 X 1-1/4″ Hex Head Bolt| 2
3/8″ Flat Washer Grade 8 YZ| 2
23 Diff. Mount, Dual Steering Stabilizer|
M8X1.25mm, 30mm Long Hex Head Bolt| 2
M8 Flat Washer Class 10.9 Z| 2
Main Body Clamp, Dual Steering Stabilizer|
M10-1.5 x 55mm Hex Head Bolts| 4
M10 Flat Washer Grade 8.8 Z| 8
M10-1.5 Toplock Nut Grade 10.9 Z| 4
Tie Rod Mounts|
3/8″ Flat Washer Grade 8 YZ| 8
3/8″-16 X 1.5 X 2.50 U-Bolt| 4
3/8” Lock Nut| 8
Stabilizer Mounts|
M12-1.75 Toplock Nut Grade 10.9 Z| 4
M12 Flat Washer Grade 8.8 Z| 8
M12-1.75 X 65mm Hex Head Bolt| 2
M12-1.75 X 75mm Hex Head Bolt| 2
WARNING
Before starting installation: ReadyLIFT Suspension highly recommends that the
installation of this product be performed by a professional mechanic with
experience working on and installing suspension products. Professional
knowledge and skill will typically yield the best installation results. If you
need an installer in your area, please contact ReadyLIFT Suspension Customer
Service to find one of our “ProGrade” Dealers.
INSTALLATION BY A PROFESSIONAL IS HIGHLY RECOMMENDED.
- A Factory Service Manual for your specific Year / Make / Model is highly recommended for reference during installation.
- All lifted vehicles may require additional driveline modifications and / or balancing.
- A vehicle alignment is REQUIRED after installation of this product.
- Speedometer / Computer recalibration is required if changing +/- 10% from factory tire diameter.
- A vehicle lift or hoist greatly reduces installation time. Installation time estimates are based on an available vehicle hoist.
- Vehicle must be in excellent operating condition. Repair or replace any and all worn or damaged components prior to installation.
ReadyLIFT recommends all steps and procedures described in these instructions
be performed while the vehicle is properly supported on a two post vehicle
lift with safety jacks.
Otherwise, park vehicle on a clean flat surface and block the rear wheels for
safety. Engage the parking brake.
Lock the steering wheel in the straight forward position with the column lock
or steering wheel locking device.
Raise the front of the vehicle and support with safety jack stands at each
frame rail behind the lower control arms.
View of the front end before work begins
Remove the (2) middle bolts on the passenger side of the
differential cover and retain the factory hardware. Remove the differential ID
tag and either place in a secure location (skip next step), or reinstall on
the driver side of the differential (see next step).
Remove the (2) middle bolts on the driveside differential cover and
discard. Install the differential ID tag on the drivers side using the factory
hardware.
Locate the center stabilizer bracket and rear axle bracket of the dual
steering stabilizer kit and the following hardware:
2 ea. — M8 x 30mm Hex Head Bolts
2 ea. — M8 Washers
4 ea. — M10-1.5 x 55mm Hex Head Bolts
8 ea. — M10 Flat Washers
4 ea. — M10-1.5 Top Lock Nuts
Install the center stabilizer bracket
onto the differential using the supplied M8 x 30mm hex head bolts and M8 flat
washers. Use the inside holes on the bracket and ensure that the bracket is
flush. Tighten bolts enough to secure the bracket to the differential, but do
not tighten completely at this time.
For years XX-22, use outside holes and 3/8 x 1 1/4 hardware.
Using the supplied M10-1.5 x 55mm Hex Head Bolts, M10 flat washers and M10-1.5
toplock nuts, fasten the rear axle bracket to the center stabilizer bracket,
clamping both around the axle tube.
Note: Only (2) bolts are visible in phot
Tighten each of the four M10 nuts and bolts, making sure that the gap between
each is approximately equal when tight.
Tighten the M8 bolts on the differential.
Torque the M8 bolts to 23ft-lbs.
Locate the driver/passenger tie rod brackets and the following hardware:
4 ea. — 3/8”x 1.5” U-bolts
8 ea. — 3/8” Flat Washers
8 ea. — 3/8” Toplock Nut
Install the driver tie rod bracket using the supplied 3/8” U-bolts, 3/8” flat
washers, and 3/8” toplock nuts. Place the plate flush against the flat face on
the bottom of the tie rod. Do not fully tighten at this time.
Note: The angled face should be pointing up and towards the front of the
vehicle.
Install the passenger tie rod bracket using the supplied 3/8” U-bolts, 3/8”
flat washers, and 3/8” toplock nuts. Place the plate flush against the flat
face on the bottom of the tie rod. Do not fully tighten at this time.
Note: The angled face should be pointing up and towards the front of the
vehicle.
Space each tie rod bracket an equal distance from the center bracket. When in
the correct position, tighten the nuts.
Torque 3/8” hardware to 30 ft-lbs.
Locate the steering stabilizers with the following hardware:
1 ea. — Stabilizer Top Plate
2 ea. — M12 x 65mm Hex Head Bolts
2 ea. — M12 x 75mm Hex Head Bolts
8 ea. — M12 Flat Washers
4 ea. — M12-1.75 Toplock Nuts
Using the M12 x 75mm bolts, washers and nuts, install the body end of the
stabilizers onto the center stabilizer bracket.
Stabilizer body end should be installed with the stabilizer top plate on top
and thecenter stabilizer bracket on bottom (as shown in photo). Do not tighten
at this time.
Install stabilizer shaft ends to the tie rod brackets using the M12 x 65mm
bolts, washers and nuts. The shaft end will sit on top of the angled face (as
shown in photo). Do not tighten at this time.
Note: If necessary, adjust the brackets that each stabilizer has an equal
amountof shaft showing on each side. Retorquethe bracket hardware.
Tighten the center M12 hardware.
Torque M12 hardware to 80 ft-lbs.
Before tie rod bracket hardware is tightened, ensure the stabilizers are
inlinewith one another and parallel to the ground. Tighten the tie rod M12
hardware.
Torque M12 hardware to 80 ft-lbs. With all the hardware tightened and
torqued to spec, complete a full lock to lock sweep of the steering to ensure
theare no clearance issues, binding or bottoming out and/or over extension of
the stabilizers.
Bolt Torcue and ID
Decimal System| Metric System
All Torques in Ft. Lbs. Maximums
Bolt Size| Grade 5| Grade 8| Bolt Size| Class 9.8| Class 10.9| Class 12.9
5/16| 15| 20| M6| 5| 9| 12
3/8| 30| 45| M8| 18| 23| 27
7/16| 45| 60| M10| 32| 45| 50
1/2| 65| 90| M12| 55| 75| 90
9/16| 95| 130| M14| 85| 120| 145
5/8| 135| 175| M16| 130| 165| 210
3/4| 185| 280| M18| 170| 240| 290
G = Grade (Bolt Strength)
D= Nominal Diameter (Inches)
T = Thread Count (Threads per Inch)
L= Length (Inches)
X = Description (Hex Head Cap Screw)
|
P = Prop erty Class (Bolt Strength)
D = Nominal Diameter (Millimeters)
T = Thread Pitch (Thread Width, mm)
L= Length (Millimeters)
X = Description (Hex Head Cap Screw)
WARNING
FAILURE TO PERFORM THE POST INSPECTION CHECKS MAY RESULT IN VEHICLE COMPONENT
DAMAGE AND/OR PERSONAL INJURY OR DEATH TO THE DRIVER AND/OR OTHERS.
Final Checks & Adjustments
Once the vehicle is lowered to the ground, check all parts which have rubber
or urethane components to ensure proper torque. Torque lug nuts to the wheel
manufacturer specs.
Move vehicle backwards and forwards a short distance to allow suspension
components to adjust. Turn the front wheels completely left then right and
verify adequate tire, wheel, brake line, and ABS wire clearance. Test and
inspect steering, brake and suspension components for tightness and proper
operation. Inspect brakes hoses and ABS lines for adequate slack at full
extension, adjust as necessary.
RECHECK ALL HARDWARE FOR PROPER TORQUE VALUES AFTER 500 MILES, AND THEN
PERIODICALLY AT EACH SERVICE INTERVAL THERAFTER.
Vehicle Handling Warning
Increasing the height of your vehicle raises the center of gravity and can
affect stability and control. Use caution on turns and when making steering
corrections.
Vehicles with larger tires and wheels will handle differently than stock
vehicles. Take time to familiarize yourself with the handling of your vehicle.
Wheel Alignment/Headlamp Adjustment
It is necessary to have a proper and professional wheel alignment performed by
a certified alignment technician. Align the vehicle to factory specifications.
It is recommended that your vehicle alignment be checked after any off-road
driving.
In addition to your vehicle alignment, for your safety and others, it is
necessary to check and adjust your vehicle headlamps for proper aim and
alignment. If the vehicle is equipped with active or passive safety/collision
monitoring and/or avoidance systems including, but not limited to, camera- or
radar-based systems, check and adjust your vehicle’s systems for proper aim
and function.
77-23200-IM-AA
www.ReadyLIFT.com
Phone:877-759-9991
References
- Foundational Technology - AMI
- ReadyLIFT | Leveling Kits | Lift Kits | Jeep Lift Kits | Block Kits | ReadyLIFT Suspension
- ReadyLIFT | Leveling Kits | Lift Kits | Jeep Lift Kits | Block Kits | ReadyLIFT Suspension
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>