MaxiMist Pro TNT ST867 Spray Tanning System User Guide

MaxiMist Pro TNT ST867 Spray Tanning System

Specifications

• Product Name : MaxiMist Pro TNT ST867 Spray Tanning System
• Model : ST867 TNT
• Usage : Professional application of liquid spray tanning solution
• Features : Control Tech Electronic Twist N Tan Spray Gun

Product Usage Instructions

Explanation of Symbols:

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates tips for use and other particularly useful information.

Field of Application:

The MaxiMist Spray Tanning System is designed for professional use with liquid spray tanning solution. Any other applications are not permitted.

Important Safety Instructions

To reduce risks, read and understand all instructions provided in the manual. Be familiar with the controls and proper usage of the equipment.

Warnings:

• Do not store flammable materials in the base unit. Store materials only in hermetically sealed containers.
• Avoid storing solvent-based materials in the base unit during operation.
• Avoid proximity to sources of ignition during spraying.
• Avoid contact with skin and eyes. In case of contact, rinse immediately and seek medical advice.
• Avoid using near water sources to prevent electrical shock.

Grounding Instructions

The product must be grounded to reduce the risk of electric shock in case of a short circuit. Ensure proper installation and grounding according to local codes and ordinances.

FAQ

• Q: Can I use any type of tanning solution with this system?
  • A : The system is specifically designed for liquid spray tanning solutions. Using other types of solutions may damage the equipment.
• Q: How should I clean the spray gun after each use?
  • A : Follow the cleaning instructions provided in the manual. Typically, you will need to flush the gun with clean water or a cleaning solution to prevent clogging.
• Q: What should I do if the system overheats during operation?
  • A : Turn off the system, unplug it, and let it cool down for at least half an hour. Check for any obstructions or issues causing overheating before resuming operation.

Congratulations on purchasing a MaxiMist™ Spray Tanning System. This product has been specially designed to provide an efficient application of tanning solution products. Take a minute to read and understand how to operate your new MaxiMist™ system and you will be able to provide the perfect tan with every application.

Read all safety information before operating the equipment. Save these instructions.

Explanation of symbols used

Field of application

The MAXIMIST™ Spray Tanning System has been specifically developed for the professional application of liquid spray tanning solution. Any application other than that described in this operating manual is not permitted.

Important Safety Instructions

To reduce the risks of re or explosion, electrical shock, and the injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and proper usage of the equipment.

WARNING! EXPLOSION HAZARD!

DO NOT store ammable materials in the base unit! Materials may only be stored in hermetically sealed containers in the base unit! Any material spills in the base unit must be wiped up immediately and allowed to dry completely before operation! DO NOT store solvent-based materials in the base unit during operation!

DO NOT use the spray guns to spray flammable substances.

• DO NOT clean spray guns with flammable solvents.
• There must be no sources of ignition such as open res, the smoke of lit cigarettes, cigars, and tobacco pipes, sparks, glowing wires, hot surfaces, etc. in the vicinity during spraying.
• Caution against dangers that can arise from the sprayed substance and observe the text and information on the containers or the specifications given by the substance manufacturer directly or via an SDS (Safety Data Sheet).
• DO NOT spray any liquid of unknown hazard potential.
• ATTENTION! Spray tanning solutions do not generally offer any protection against sunburn. Repeated unprotected contact with the sun increases the risk of skin cancer, skin aging, and other harmful effects.
• This Spray Tanning System is intended for use by persons 14 years and over.
• DO NOT let children play with the Spray Tanning System.
• NEVER leave the spray tanning system unattended.
• Stay alert and watch what you are doing.
• DO NOT operate the unit when fatigued or under the influence of drugs or alcohol.
• Follow all appropriate local, state, and national codes governing ventilation, re-prevention, and operation.
• The United States Government Safety Standards have been adopted under the Occupational Safety and Health Act (OSHA). These standards, particularly part 1910 of the General Standards and part 1926 of the Construction Standards should be consulted.
• NEVER direct the spray gun at animals.
• Ensure that the spray area is well-ventilated.
• DO NOT breathe in spray tanning solution. Wearing nasal plugs and operating an extraction fan designed for the purpose is recommended.
• DO NOT spray into the eyes.
• If spray tanning solution is sprayed into the eyes, wash them out with water immediately and consult a doctor.
• DO NOT spray spray tanning solution into open wounds or onto damaged skin.
• Cover your hair when spraying your face. Otherwise, bleached hair in particular could be stained by the spray tanning solution.
• NEVER immerse the Spray Tanning System in water
• WARNING! NEVER use your Spray Tanning System near bathtubs, shower trays or other receptacles that contain water.
• NEVER place the Spray Tanning System near a washbasin or another water source. Water always represents a hazard even when the system is switched o.
• NEVER expose the equipment to rain.
• DO NOT use outdoors or operate where aerosol (spray) products are being used.
• NEVER drop or insert any object into any opening or hose.
• NEVER block air openings of the spray turbine.
• Keep the electrical cord plug and spray gun trigger free from liquids.
• NEVER hold the cord at plug connections to support the cord. Failure to observe may result in an electrical shock.
• Keep the cord away from heated surfaces.
• NEVER operate a spray tanning system if the cord or plug is damaged.
• As additional protection, the installation of a circuit protective device such as ALCI or GFCI is recommended. Ask your installer for advice.
• Connect to a grounded outlet and use grounded extension cords.
• DO NOT use a 3 to 2 adapter.
• The system is equipped with a thermal release which disconnects the system in case of overheating. In this case, turn the system, remove the plug, and let the system cool down for at least 1/2 hour. Eliminate the cause of heating, e.g. bent hose, soiled air lter, slots for air intake covered.
• Unplug the turbine before cleaning any parts.
• Use only manufacturer-authorized parts. The user assumes all risks and liabilities when using parts that do not meet the minimum specifications and safety devices of the turbine manufacturer.
• NEVER open the Spray Tanning System yourself to carry out electrical repairs!
• DO NOT place the spray gun on its side, as the material could leak out.

Grounding Instructions

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING – Improper installation of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to either at blade terminal. The wire with insulation having a green outer surface with or without yellow stripes is the grounding wire and must be connected to the grounding pin. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided. If the plug will not t the outlet, have the proper outlet installed by a qualified electrician.

This product is for use on a nominal 120-volt ac circuit and has a grounding plug that looks like the plug illustrated below. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter shall be used with this product.

Important Electrical Information

Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A SJT-type cord is required. Cord shall be 14 AWG minimum for general indoor use.

SAVE THESE INSTRUCTIONS

Processable materials

Liquid spray tanning solution

Only use spray tanning solution up to the expiry date specified on the package. 12 M  means, for example, that the substance can be used for 12 months after opening. The actual date of opening needs to be noted by the user and marked on the container or package.

Non-processable materials

All materials not approved for skin treatment

Description (Fig. 1)

1. Air cap /Nozzle
2. Union nut
3. Spray attachment (3 pcs.)
4. Trigger
5. Gun handle
6. Air volume control
7. Air hose
8. ON/OFF switch
9. Material volume regulation
10. Carry handle
11. Gun holder
12. Container
13. Closure
14. Air hose connection
15. Mains switch
16. Deposition tray for small parts
17. Cover of air filter compartment
18. Air hose retainer
19. Deposition tray
20. Service kit (suction tube, container seal, 2 air filters and lubricant)

Preparation of the spray area

• Remove all objects from the spray area if possible, to avoid contamination from overspray.
• Work in a room with a smooth, easy-to-clean surface. The use of a spray booth/spray tent and tanning extraction fan is recommended.

General preparations before the application of spray tanning solution

Test the compatibility of the spray tanning solution on a small patch of skin approx. 24 hours before the actual application of the spray tanning solution. Stop application if skin irritation occurs.

• Approx. 24-48 hours prior to treatment remove body hair by shaving or waxing.
• Do not apply any perfume, deodorant or make-up. These products can negatively influence the tanning result.
• On the day of the treatment wear dark, loose-fitting clothing, in order to prevent discoloration of clothing by the spray tanning solution.
• Remove all jewelry, in order to avoid discoloration by the spray tanning solution.

Preparation of the skin

Correct preparation of the skin is key to an even and long-lasting tanning result.

Please note the following instructions:

• Remove all dead skin cells by means of exfoliation before applying the spray tanning solution.
• Make sure that the moisture content of the skin is as uniform as possible. Use barrier cream for dry areas (e.g. elbows and knees). Let the moisturizer dry before commencing the treatment.
• Apply a little balm to lips, nails, palms of the hands, eyebrows and the hairline for protection.

Start-up

Before connecting to the power supply, be sure that the supply voltage is identical the value given on the rating plate.
Always lower the carry handle in the cover before opening the cover. Press the locking device on both sides to this purpose.

1. Open the closure (Fig. 2, 1) and fold open the cover of the device.
2. Open the air hose retainer (Fig. 2, 2).
3. Remove the air hose and connect it to the air hose connection (Fig. 3).
4. Close the air hose retainer again.
5. Unroll the power cord and slide the cord grommet into the provided recess (Fig. 4)
   • WARNING : DO NOT close the cover if the cord grommet is not positioned correctly. The power cord could otherwise damaged!
6. Remove the spray attachment from the deposition tray.
7. Unscrew the container from the spray attachment.
8. Prepare spray tanning solution according to the manufacturer’s instructions and pour it into the container.
9. Screw the container firmly onto the spray attachment.
10. Connect the front part of the gun and the gun handle to each other. (Fig. 5)
11. Close the device cover and pull the carry handle upwards. This makes the gun holder accessible.
12. Put the spray gun onto the gun holder at the turbine.
13. Place the turbine only on anat and clean surface. Otherwise, the turbine may suck in dust, etc.
14. Switch on the switch by pressing “I” at the turbine (Fig. 6).

Operation

How the Spray Tanning system is handled, including preparation of the work place and spray tanning solution as well as the real result, is the sole responsibility of the operator.
Spray Tan Direct excludes any liability for damage that may arise from overspray, applica-tion errors, touch-ups, or non-compliance with the instructions provided here.

• Press the On/O switch at the gun handle (Fig. 7, 1).
• Turn the material control (Fig. 7, 2), in order to adjust the desired delivery rate.
• lower material volume (-):  turn anti-clockwise
• higher material volume (+): turn clockwise

Your goal is a 4-inch wide spray pattern spraying 4 inches away.

• Turn the air volume control (Fig. 7, 3), in order to optimize the atomization and reduce overspray.
  • less air (-): turn anti-clockwise
  • more air (+): turn clockwise
• Turn the air cap (Fig. 8, 1) with the union nut (2) slightly unscrewed, to adjust the the shape of the spray jet:
  • Fig. 9a vertical at jet:
• For spray movements from left to right
  • Fig. 9b horizontal flat jet:
• For spray movements from top to bottom
• Pull the trigger to spray the tanning solution.

Tips on using the spray tanning system

Before commencing application, check that all necessary protective measures (nasal plugs, hair covering) have been taken.

Notice: Practice on a large piece of newspaper or cotton towel first in order to and the optimal settings for the spray tanning solution used.

• If a tanning extraction fan is available, place in the near vicinity of spraying and switch it on.
• Avoid interruptions during the spray movement. Maintain a constant pace.
• The spray movement should come from the arm, not just from the wrist.
• This ensures that a uniform distance is maintained between the spray gun and the body during the spray operation.
• Fig. 10 a : CORRECT even distance
• Fig. 10 b : INCORRECT uneven distance will result in uneven tanning
• Move the spray gun at an even speed.
• When tanning is complete, switch the turbine and any tanning extraction fan (if used) after the fumes/mist have cleared.

After application of the spray tanning solution

• The full tanning effect develops during the first 24 hours after the treatment.
• Allow the spray tanning solution to dry for 5-10 minutes before getting dressed again.
• You can also use the air from the air hose to accelerate the drying process of the spray tanning solution. To do this, simply remove the spray attachment from the handle and switch the system on.
• Do not shower or bathe in the first 6-8 hours after application, as this will affect the tanning result. This will vary depending on the tanning solution used.
• Prolonged hot baths and showers should be avoided, in order to maintain the tanning effect for as long as possible. Daily moisturizing of the skin is also recommended.

Cleaning the spray tanning system

Clean the Spray Tanning System as required at the end of the working day. A dried spray tanning solution makes cleaning more difficult and can even damage the system.

1. Turn the system.
2. Divide the spray gun. Press the hook (Fig. 11 “click”) slightly downwards. Turn the gun front part and gun rear part against each other.
   • WARNING : NEVER hold the gun handle under water or immerse it in liquids. Clean the housing only with a moistened cloth.
3. Unscrew the container.
4. Pour any remaining spray tanning solution back into the original packaging.
5. Clean the container and feed tube with a brush.
6. Clean the ventilating bore (Fig. 12, 1).
7. Pour 2 FL. oz of MaxiClean Spray Gun Cleaner into the container. Screw the container back on. DO NOT use ammable materials for cleaning purposes.
8. Assemble the gun again.
9. Turn on the system and spray the cleaner into a sink or a cloth.
10. Fill a container with 2 . oz water, and spray until empty.
11. Repeat the above procedure until the water emerging from the nozzle is clear.
12.  Turn the system and divide the spray gun.
13.  Screw the container and empty it. Pull out the feed tub with the container seal.
    • CAUTION! NEVER clean the seals, nozzles or air holes of the spray gun with metal objects.
14. Unscrew the union nut and remove the air cap and nozzle (Fig. 13). Clean the air cap, nozzle seal, and nozzle with a brush and water.
15. Clean the outside of the spray gun and container with a cloth soaked in water.
16. Assemble the parts again (see “Assembly”).

Assembly

1. Slide the nozzle seal (Fig. 14, 1) with the groove (slot) facing forward into the nozzle (2).
2. Put the nozzle onto the gun body and the correct position by turning it.
3. Put the air cap onto the nozzle and tighten it using the union nut.
4. Place the container seal (Fig. 15, 1) from below on the feed tube (2) and slide it over the collar, while turning the container seal slightly.
5. Insert the feed tube with the container seal in the gun body.

Maintenance

Important! NEVER operate the system without the air filter; dirt could be sucked in and interfere with the function of the system.
DO NOT store any objects in the air filter compartment.

1. Change the air filter if it is soiled (check daily).
2. Open the cover of the air filter compartment (Fig. 16).
3. Insert a new air filter into the compartment.
4. Close the cover of the air filter compartment.
   • In order to mount the gun more easily apply lubricating grease (enclosed) liberally to the O-ring at the spray attachment (Fig. 17, 1) and to the O-ring of the plug connection of the air hose (Fig. 17, 2).

Storage

Store the unit in a safe place after the air hose  (FIg. 18, 1) and all accessories have been placed inside the unit.

Spare parts

This unit contains no user-serviceable electrical parts. DO NOT attempt to service the unit yourself.

Spare Parts List (Fig. 19)

Correction of Malfunctions

Technical Data

Environmental protection

The appliances and accessories should be recycled in an environmentally friendly way. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtaining information from a specialist retailer.

12 Month Limited warranty

2 Year Turbine Motor warranty

This machine and equipment is guaranteed by Spray Tan Direct for a total period of TWELVE MONTHS from the ORIGINAL date of purchase by the ORIGINAL PURCHASER. Proof of purchase to be included and all SHIPPING CHARGES on returns are to be prepaid. The client is responsible for shipping both the return and the replacement unit. Spray Tan Direct upon examination of the machine/equipment will replace or repair at their discretion any defects in material or workmanship.

This WARRANTY does NOT include misuse, damage, neglect, alterations, disassembled equipment or modifications, lack of maintenance, cleaning, water damage to electrical parts, and INCORRECT VOLTAGE CONNECTION. This WARRANTY is in lieu of all other express warranties, any WARRANTY implied by law, including but not limited to implied warranties of merchantability or fitness, is excluded to the maximum extent permitted by law and, if not excludable, it is limited to the duration of the express warranty. No representative or person is authorized to extend this warranty or to create for Spray Tan Direct any other liability in connection with the sale of any Spray Tan Direct product. Spray Tan Direct shall not be liable for any consequential, incidental, or special damages of any kind directly or indirectly resulting from a breach of any express or implied warranty.

Some states do allow the exclusion of limitation of incidental or consequential damages or limitations on the length of any warranty so that the above limitations and exclusions may not apply to you; however, to the maximum extent permitted under applicable law, the only rights and remedies shall be to obtain a replacement for any
defective product. This warranty gives you specific legal rights and you may also have other rights.

What’s covered?

1. The turbine motor for 24 months.
2. The power switch on the turbine unit.
3. Leaking container and spray guns.

PLEASE CONTACT YOUR DEALER FOR ALL WARRANTY AND SUPPORT ISSUES

For a great application technique visit www.hvlptanning.com

• Spray Tan Direct 11920 31st Ct N St.Petersburg,
• Fla 33716 727-834-9435

References

• Loading...

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>