EXALITE CMY 400W EXL ML Spot Beam Wash User Manual

EXALITE CMY 400W EXL ML Spot Beam Wash

Product Information

• Product Name: EXL-ML Spot Beam Wash CMY 400W
• Product Type: Lighting Fixture
• Protocol: DMX512-A (with RDM support)

Product Usage Instructions

1. Operating the Fixture:

   • Use the touch display or the encoder/button to operate the fixture.
   • If the fixture supports touch, you can use the TFT displayer on the left side to set light settings or view the light state by tapping on the item or value.
   • If touch is disabled, use the rotary encoder with a button/key on the right side to set or view the item. Press the encoder button/key to confirm the selection. Rotate the encoder or press the key again to set the parameter value. Finally, press the encoder button/key again to save the value or setting.

2. Setting Parameter Values:

   • When a selected item requires a value modification, a dialog box (Figure 4) will appear.

   • To quickly modify the value, slide the slider to the desired position or click the “up” or “down” button on the right side.
     Alternatively, use the rotary encoder on the right side of the panel.

   • Once the value has been modified, press the “apply” button in the bottom left corner to apply it to the light. Note that this does not save the value.

   • To save the modified value, click on the “OK” button in the lower right corner at any time.

3. Boolean Parameter Setting:

   • If the selected parameter is a Boolean value (e.g., ON or OFF), you can directly modify the setting by clicking on the corresponding item. The setting will be saved immediately.
   • If the parameter is a key item, clicking on the corresponding item will prompt a confirmation dialog (Figure 5). Click “sure” to confirm.

4. Sub Menu Parameter:

This section provides additional settings for specific parameters. Please refer to the user manual for detailed instructions.

1. Fixture Operating Mode Setting:
   • This section allows you to set the operating mode of the fixture. The available options are:
   • DMX Ctrl: Receive DMX signal and RDM signal.
   • Auto Run: The fixture runs automatically according to built-in programs.
   • Sound Ctrl: When the fixture detects a strong sound, it automatically runs a scene according to the built-in program. Otherwise, it stays in the last scene.
   • Scene Mode 01: Runs a set scene, which supports custom editing of up to 10 scenes. Outputs the specified scene from 1 to 10.
   • M/S Choose Master and slave selection. In non-DMX mode, select the mode of data output. The fixture detects the DMX cable state and automatically switches output to prevent data conflicts.
   • Lamp Switch: Choose the lamp switch operating mode. Auto mode automatically loops the output scene in the set scene time (non-zero) order, while scenes with time 0 are automatically ignored.
2. Master/Slave Mode:
   • In non-DMX mode, the fixture can operate as either a master or a slave.
   • Master Mode: The fixture runs the built-in program and outputs data (synchronization) if the DMX signal is absent.
   • Slave Mode: The fixture runs the built-in program but does not output data.
   • Auto Mode: If the DMX signal is absent, the fixture runs the built-in program. Otherwise, it follows the DMX signal.

Product Instruction

• Input voltage: 100-240V~ 50/60Hz
• Power consumption: 500 W
• Light source: powerful 400W white LED bulb
• Optical System: High-efficiency optical system
• Light source life: 50000 hrs
• Color Temperature Output: 7,000K
• Pan & Tilt: 540 degrees & 270 degrees (16bit )
• Control mode: DMX512, RDM, Auto-run, Sound active, Master-slave, Built-in program
• Software upgrade: online software upgrade is available
• Channel mode: 22 &26 channels
• Color Wheel: 8 colors + white light.
• Static Gobo Wheel: 12 gobos plus open
• Rotating Gobo Wheel: 7 gobos plus open, convenient replacement
• Animation Wheel: animation wheel, rotatable and replaceable, with outstanding water and flame effect
• Color Mixing System: Linear CMY color mixing+Variable CTO( 3,200-7,000K)
• Prism system: 6-facet linear prism and 8+8-facet prism

Zoom range:

• Beam Mode: 4°~8°
• Spot Mode: 4°~35°
• Wash Mode: 8°~60°
• Dimer: 0~100% smooth dimming
• Focusing system: Motorized focus
• Frost system: Independent frost flitter
• Atomization system: independent atomization effect, soft and natural light spot
• Strobe: 0-30 times/sec. Adjustable speed strobe effect. Strobe macro function
• Cooling system: smart axial fans. (electronic temperature control overheating protection, electronic temperature control automatic power-off protection when the overheating system fails.)
• Display: LCD display+4 keys
• Protection level: IP20
• Product net weight: 2 2.5KG
• Fixture Dimensions: 38cm27cm 62cm

RDM Note

• RDM is an extended version of the DMX512-A protocol. It is a remote device management protocol.
• Traditional DMX512 protocol communication is one-way communication.
• The protocol is based on the RS-485 bus.
• RS-485 is a time-sharing multi-point, half-duplex protocol. Only one port is allowed to output at the same time. So, when using RDM, we should pay attention to it Figure 3 Panel Diagram

Operation

1. Operate fixture with touch or encoder/button
   • The left area is TFT Displayer and touch(the product which supports touch), chick item or value with a finger will complete the operation of set light setting(parameters) or view light state.
   • The area on the right-hand side is rotary encoder with a button or key, As an auxiliary input interface, if the fixture disables the touch function, the encoder/key can choose to set or view the item, and then press the encoder button/key to confirm the selection, rotary encoder or push key again set the parameter value, finally, Press encoder button/key one again to save value or setting.
2. Parameter value setting
   • When the selected item’s value needs to be modified, the dialog shown in Figure 4 will pop up.
   • Modify value: Can quickly modify the value by pulling the slider to the desired position, or clicking the button ‘up’ or ‘down’ with a finger on the right side to set the exact desired value, another way is rolling the encoder on the right-hand side of the panel.
   • Apply value: When the Value has been modified, Then press the bottom of ‘apply’ in the left corner to apply it to the light, but haven’t saved；
   • Save Value: Any time, click on the lower right corner of the “OK” button, the setting will be saved into internal memory.
3. Boolean parameter setting
   • hen the selected parameters is a Boolean value (such as ON or OFF), can directly modify the setting by chick corresponding item, the setting will be saved right now.
   • hen the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will pop up to ask for confirmation. Click ‘sure’ to confirm.

Sub Menu Parameter

Fixture operating mode setting

operating mode

automatically runs a scene

according to the built-in program, otherwise, it will stay the last scene

Scene Mode 01| runs in a set scene, which supports most of the custom editing of 10 scenes.
1~10| outputs the specified scene
Auto| Automatically loops the output scene in the set scene time (non-zero)

order and the scene with time 0 automatically ignore

M/S Choose| Master and slave selection, non-DMX mode takes effect, select the mode of data output, fixture detect DMX cable state automatic switch output, prevent

data conflicts

Mast

er

| fixture runs a built-in program. If DMX has no signal, it outputs data

(synchronization), otherwise, it does not output data.

Slave| mixture runs the built-in program and do not output data
Auto| If DMX has no signal, the fixture will run a built-in program. Otherwise,

the fixture will run in DMX Mode(follow DMX).

Lamp switch| (Lamp light source) pop-up confirmation dialog box, select “SURE” to confirm the current operation, turn on or off the lamp, switch time interval limited to 30

seconds

Off| the current lamp output is off
On| The current lamp output is turned on

Set display

DISPLAY SETTING

screen’s display content or method.
OFF| Keep the last operation page
| Mode1| Black
---|---|---
Mode2| Black screen, showing the address code of the current fixture in the

lower left corner.

Mode3| Display trademark information, address code, and operation mode.
Screen Rot| Set the display direction of the screen.
OFF| No reverse display
ON| Reverse display
AUTO| Automatically detect the direction of lamps and automatically

switch direction.

DMX Indicate| Set the indication mode of the DMX signal indicator.
Mode1| When the signal is bright, no signal is off.
Mode2| When the signal is off, no signal is bright.
Mode3| When the signal is flashed, no signal is off.
Signal Bright| Set the brightness of the signal indicator
1~10| 10
Screen Light| Set the screen backlight for 10 seconds without operation
1~10| 10
Touch switch| Choose whether to disable the touch function. When the screen touch is accidentally damaged, you can disable the touch function and use the auxiliary input

to set the fixture.

Touch| When the screen touch function works anomaly, you can enter the corrected page

correction screen touch

Scene

SCENE MODE

Scene

Select

| Select the current operation scenario.
---|---
1~10| The 10 scenes set the format
Scene Time| Sets the retention time of the current scene when it is automatic, unit in 0.1

seconds.

0| The current scene is not output in automatic scene output.
1-255| 0..1s-25.5s
1. PAN| 0-255| Set up the data of each channel, and the contents and order of the display are one-to-one correspondence with the channel list of fixtures.
……| 0-255
……| 0-255
N. Function| 0-255

Set light run parameter

Enter the page shown in Figure 6-5, adjust the field parameters of the fixture, facilitate the installation of the fixture, etc.
ADVANCED SETTING

the out-of-step fault is recorded.

Pan Offset| Setting the zero point of the PAN of the fixture
4-150|
Tilt Offset| Setting the zero point of the TILT of the fixture
4-48|
Data hold| When the fixture is not equipped with a DMX signal, the output state of the

fixture

OFF| No signal, so the motor and light source return to the position and

state when reset is completed.

ON| No signal, keep the last frame DMX data output.
Lamp mode| Set the way to first open the lamp after powering up
Power on| Turn on the lamp at power up and reset the lamp after 30

seconds.

After

reset

| Reset the fixture after 3 seconds when power-on, and turn on the

lamp after reset.

Manual| After resetting, manually turn on the lamp through the menu or

console.

Factory

Setting

| Pop up the confirmation box, select “SURE”, and return the lamp parameters to the factory settings.

• When choosing power-on mode, the lamp will wait for 30 seconds after power-on, let the lamp fully start, internal voltage is stable enough, then start the reset program, if the field capacity is stable, recommend power-on mode.
• When the fixture can not calibrate the position, please check whether the “P/T Rectify” is turned off.
• When the signal is unplugged, check the Data Hold setting first if the position of the fixture is not output as expected.
• When setting the XY offset, after setting up, please control XY with the maximum stroke first to check that XY will not bump into the positioning rod or shell.

Status and information

Stepper info| Display information status of all motors and signals in the fixture.
---|---
Hall| No display, indicating that the motor has no Hall, 0 indicating

that the motor leaves the correction position point, 1 indicating that the motor is in the correction position point

Status| Display motor reset status
PAN| Display real-time position value of PAN optocoupler feedback
TILT| Display real-time position value of TILT optocoupler feedback
PAN OP| Displays the PAN TILT optocoupler two signal level state,

binary

Error Logging| Show the latest 8 error records when the fixture is reset and running. The error records

are not saved after power failure. The current power cycle is valid.

Error Logging| Total number of failures detected after power on
12：:03| The time of power failure when the fault occurs is in minutes.
Hall error| The effective hall signal is not detected when the motor is reset
| Hall short| When the motor is reset, the hall signal of the motor is always

effective

---|---|---
Opti error| No effective optocoupler signal is detected when the motor is

reset.

Lose stop| The corresponding motor is out of step during its operation.
Hit| Striking the positioning rod when the motor is reset
Lamp error| Lamp explosion accident
NTC error| The temperature sensor signal is abnormal
Fan error| The main fan is not working properly.
Fixture status| Displays the critical state data of the current fixture for reference.
Communication pre| 0~100%, Communication quality of internal data link of lamps

and lanterns

Error cnt| The number of erroneous frames was detected after the power

on, and the total number of erroneous frames was detected.

Light Temperature| Show the temperature of the current light source, “—” means

no detection.

Panel Temperature| Displays the temperature of the current display panel or the

ambient temperature.

Sensor1 Temperature| Display the ambient temperature of the motherboard

temperature or the motherboard installation position.

Version| Display the information and version of the current fixtures, important reference after

sales maintenance.

Device| The name of the fixture is the same as the equipment

information of RDM.

Model| The type of fixture is the same as the model information of

RDM.

Panel| The firmware version and serial number of the display panel
Main Board| Firmware version and serial number of motherboard 1
Light time| Record the total cumulative time of light source opening, unit minute, user manual

cleaning, as a reference for regular maintenance of light source time

Total time| The total accumulated time for recording the opening of the fixture is not allowed to be

removed.

Channel table

CHANN EL1

| ****

CHAN NEL2

| ****

NAME

| ****

VALUE

| ****

DEFINE

---|---|---|---|---
CH1| CH1| PAN| 0-255| 0-540
CH2| CH2| PAN Fine| 0-255|
CH3| CH3| TILT| 0-255| 0-270
CH4| CH4| TILT Fine| 0-255|
CH5| | XY speed| 0-255| fast to slow
CH6| CH5| Dimmer| 0-255| 0-100% Dimmer
CH7| CH6| Strobe| 0-3| Drak
| | | | 4-103| Slow strobe to fast strobe|
---|---|---|---|---|---|---
104-107| White
108-155| Slow strobe to open strobe
156-207| Slow strobe to close open strobe
208-212| White
213-251| Free strobe
252-255| White

CH8

| ****

CH7

| ****

Color

| 0-127| White
128-133| Color1
134-138| Color2
139-143| Color3
144-149| Color4
150-154| Color5
155-159| Color6
160-164| Color7
165-170| Color8
171-175| Color9
176-180| Color10
181-185| Color11
186-191| Color12
192-220| Rotate forward (fast to slow)
221-224| Stop
225-255| Rotate reverse (slow to fast)
CH9| CH8| C| 0-255|
CH10| CH9| M| 0-255|
CH11| CH10| Y| 0-255|
CH12| CH11| CTO| 0-255|

CH13

| ****

CH12

| ****

Gobo

| 0-4| White
5-9| GOBO1
10-14| GOBO2
15-19| GOBO3
20-24| GOBO4
25-29| GOBO5
30-34| GOBO6
35-39| GOBO7
40-44| GOBO8
45-49| GOBO9
50-54| GOBO10
55-59| GOBO11
60-64| GOBO12
65-69| Shake slow to fast GOBO2
70-74| Shake slow to fast GOBO3
75-79| Shake slow to fast GOBO4
80-84| Shake slow to fast GOBO5
85-89| Shake slow to fast GOBO6
| | | | 90-94| Shake slow to fast GOBO7|
---|---|---|---|---|---|---
95-99| Shake slow to fast GOBO8
100-104| Shake slow to fast GOBO9
105-109| Shake slow to fast GOBO10
110-114| Shake slow to fast GOBO11
115-119| Shake slow to fast GOBO12
120-127| GOBO12
128-190| Rotate forward (fast to slow)
191-192| Stop
193-255| Rotate reverse (slow to fast)

CH14

| ****

CH13

| ****

Rot Gobo

| 0-9| White
10-19| GOBO1
20-29| GOBO2
30-39| GOBO3
40-49| GOBO4
50-59| GOBO5
60-69| GOBO6
70-79| GOBO7
80-89| Shake slow to fast GOBO1
90-99| Shake slow to fast GOBO2
100-109| Shake slow to fast GOBO3
110-119| Shake slow to fast GOBO4
120-129| Shake slow to fast GOBO5
130-139| Shake slow to fast GOBO6
140-149| Shake slow to fast GOBO7
150-200| Rotate forward (fast to slow)
201-205| Stop
206-255| Rotate reverse (slow to fast)

CH15

| ****

CH14

| ****

Gobo rot

| 0-127| 0-400 degrees
128-190| Rotate forward (fast to slow)
191-192| Stop
193-255| Rotate reverse (slow to fast)
CH16| | Gobo fine| 0-255|

CH17

| ****

CH15

| ****

Prism1

| 0-63| Close prism
64-127| Insert prism1

CH18

| ****

CH16

| ****

Prism1 Rot

| 0-127| 0-400 degrees
128-190| Rotate forward (fast to slow)
191-192| Stop
193-255| Rotate reverse (slow to fast)

CH19

| ****

CH17

| ****

Prism2

| 0-63| Close prism
64-127| Insert prism2

CH20

| ****

CH18

| ****

Prism2 Rot

| 0-127| 0-400 degrees
128-190| Rotate forward (fast to slow)
191-192| Stop
193-255| Rotate reverse (slow to fast)

CH21

| ****

CH19

| ****

Frost

| 0-127| None
---|---|---|---|---
128-255| Insert frost
CH22| | Autofocsus| | None

CH23

| ****

CH20

| ****

Zoom

| ****

0-255

| ****

small to large

CH24

| ****

CH21

| ****

Focus

| ****

0-255

| ****

far to near

CH25| | Focus fine| |

CH26

| ****

CH22

| ****

Function

| 210-215| Reset XY(over 6 seconds)
220-235| Reset effect moto(over 6 seconds)
240-255| Reset all(over 6 seconds)

• PRODANCE, s.r.o.
• Toužimská 897/E7
• 199 00 Praha 18 – Letňany
• T: 220 806 054 E:[email protected]
  www.eprodance.cz

References

• Profesionální světelná a zvuková technika | ePRODANCE.cz

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>