FANIMATION FPS7981 Embrace 44TM Snugger Ceiling Fan Owner’s Manual

FANIMATION FPS7981 Embrace 44TM Snugger Ceiling Fan

Product Information

• Net Weight: 23.68 lbs (10.74 kg)
• Model No.: FPS7981*
• Limited Lifetime Warranty: Extends to the original purchaser of a Fanimation Fan

Important Safety Instructions

To avoid fire, shock, and serious personal injury, please follow these instructions:

• Keep out of reach of children and ensure that they do not play with the appliance.

Tools Needed for Assembly

Materials:

• Three wire connectors (supplied)

Before assembling your ceiling fan, refer to the section on the proper method of wiring your fan. If you lack wiring knowledge or experience, it is recommended to have your fan installed by a licensed electrician. The wiring outlet box and box connectors must be of the type required by local code. The minimum wire size would be a 3-conductor (2-wire with ground) of the following sizes:

If any parts are missing, please contact your local retailer. Do not install or use the fan if any part is damaged or missing. This product is designed to use only those parts supplied with this product and/or any accessories specifically designated for use with this product by Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage.

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 35 Ibs. See page 5 of owner’s manual for support requirements. Consult a qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical knowledge or experience, have your fan installed by licensed electrician.
6. Suitable for use with solid-state speed controls.
7. This fan is to be used in dry location only.
8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it should be connected to an equipment grounding conductor.

WARNING: TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE ISOLATING WALL CONTROL/SWITCH.

WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property damage.

FCC STATEMENT

WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

If the intentional radiator can be classified as a Class B digital device or a PC peripheral, then shall include the following or equivalent:

Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED LIFETIME MOTOR WARRANTY – If any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY – If your fan motor fails at any time within one year from the original purchase, due to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaserwill be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding, tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary from state to state.
10. A certain amount of wobble is normal and should not be considered a problem or a defect.

This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan

Tools Needed

Tools Needed for Assembly

• One Phillips head screwdriver
• One stepladder
• One ¼” blade screwdriver
• One wire stripper
• Three wire connectors (supplied)

WARNING: Before assembling your ceiling fan, refer to section on proper method of wiring your fan. If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.

Materials

Wiring outlet box and box connectors must be of type required by local code. The minimum wire would be a 3- conductor (2-wire with ground) of the following size:

Installed Wire Length/ Wire Size A.W.G.

• Up to 50 ft./ 14
• 50 – 100 ft./ 12

NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing, contact your local retailer.

Unpacking Instructions

For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be helpful in finding your place should you be interrupted.

WARNING: Do not install or use fan if any part is damaged or missing. This product is designed to use only those parts supplied with this product and/or any accessoriesdesignated specifically for use with this product by Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts.

• Ceiling Bracket Assembly
• Fan Motor Assembly
• Housing
• Light Plate Assembly
• Socket Plate Assembly
• Glass
• Steel Cap Assembly
• Blade Holder Set
• Blade Set
• Bulb
• Hand Held Remote

Hardware bags:

• Seven 1/4″-20 x 14 mm Phillips Head Screws, with Lock Washers
• Ten 3/16″-24 x 14 mm Washer Head Screws with Fiber Washer
• Four Wire Connectors
• 4″ Phillips Screwdriver

1. Check to see that you have received the following parts:
   • NOTE: If you are uncertain of part description, refer to exploded view illustration. (Figure 1)

Energy Efficient Use of Ceiling Fans

• Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the middle of the room and at least 7 feet above the floor and 18 inches from the walls. If ceiling height allows, install the fan 8 – 9 feet above the floor for optimal airflow. Consult your Fanimation Retailer for optional mounting accessories.

Turn Off When Not in the Room

• Ceiling fans cool people, not rooms. If the room is unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round

• Summer Season: Use the ceiling fan in the counterclockwise direction. The airflow produced by the ceiling fan creates a wind-chill effect, making you “feel” cooler. Select a fan speed that provides a comfortable breeze, lower speeds consume less energy.
• Winter Season: Reverse the motor and operate the ceiling fan at low speed in the clockwise direction. This produces a gentle updraft, which forces warm air near the ceiling down into the occupied space.Remember to adjust your thermostat when using your ceiling fan – additional energy and dollar savings could be realized with this simple step!

Electrical and Structural Requirements

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 HZ, 15 Amp Circuit. Electrical code requires use of a fan-rated outlet box tosupport the extra weight and motion associated with a ceiling fan. A fan-rated box will be labeled as such and typically supports up to a 70lb ceiling fan. Fan-Rated Outlet Boxes vary in ratings and design. Ensure the ratings of your ceiling fan outlet box meet the requirements for the ceiling fan being installed. Figure 1, Figure 2 and Figure 3 depicts different structural configurations that may be used for mounting the outlet box.

Low profile box (Figure 1)

• A 12-in.-deep pancake box is meant to be screwed to a joist or block. It’s used if only one cable is coming into the box. It is also available in a saddle-mount configuration.

Deep box (Figure 2)

• A 2-14-in.-deep box can be attached to blocking between joists and is roomy enough to handle more than one cable.

Deep box with brace (Figure 3)

• Paired with a deep box, this hanger is meant to span between two joists and takes the place of wooden blocking.

WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked acceptable for fan support of 15.88 kg (35 lbs) or less and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of luminaires are not acceptable for fan support and may need to be replaced, consult a qualified electrician if in doubt.

If your fan is to replace an existing light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.

WARNING

• Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.
• To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician.

How to Hang Your Ceiling Fan

WARNING

• The fan must be hung with at least 7´ of clearance from floor to blades. (Figure 1)
• To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging.
  • NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation.
• The outlet box must be securely anchored and capable of withstanding a load of at least 35 lbs. Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wallboard until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall.

1. Securely attach the ceiling junction box acceptable for ceiling support into the building structure. Junction box is not supplied with the fan. (Figure 2)
2. Remove the four screws and hex nuts with flat washer from the ceiling bracket assembly. Retain the screws, hex nuts and flat washers for later. (Figure 3)
3. Using the ceiling junction box screws provided with the ceiling junction box, securely attach the ceiling bracket to the ceiling junction box as shown. (Figure 4)
4. Hang the Motor Assembly as shown. (Figure 5) You can now proceed with the electrical wiring of your fan.

How to Wire Your Ceiling Fan

How to Wire Your Ceiling Fan – Remote Control

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.

WARNING

• To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.

NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation.

1. Setting the Code: The remote unit has 16 different code combinations. It may be necessary to test a couple of frequency code settings to improve signal reception and/or eliminate interference from other remote control household items. Multiple fans should have different code settings to allow independent fan control. To set the code, perform these steps.
2. Transmitter: remove battery cover. Press firmly below arrow and slide battery cover off. Slide code switches to your choice of up or down position. Factory setting is all up. Do not use this position. With a small screwdriver or ball point pen slide firmly up or down (Figure 1a). Replace battery cover on the transmitter.
3. Receiver: Slide code switches to the same positions as set on your transmitter (Figure 1b).

How to Wire Your Ceiling Fan

1. Connect the green grounding lead from the ceiling bracket to the supply grounding conductor (this may be a bare wire or wire with green colored insulation). Securely connect wires with a wire connector. Securely connect the white receiver wire (coming from fan) to the white supply (neutral) wire using a wire connector. Securely connect the black receiver wire (coming from fan) to the black supply wire using a wire connector. (Figure 1)
2. After splicing and making the wire connections, the wires should be spread apart and turned upward with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box. (Figure 1)

How to Assemble

How to Assemble Your Ceiling Fan

1. Assemble the motor assembly to ceiling bracket assembly using the previously removed hex nuts and flat washers and securely tighten all hex nuts. (Figure 1)
2. Assemble the housing to ceiling bracket assembly using the previously removed screws and securely tighten all screws. (Figure 2)

How to Assemble the Ceiling Fan Blades

1. Position the blade over the blade holder with threaded posts showing. Make sure the bottom edge of the blade is fully seated against the blade holder. With a phillips screwdriver, tighten 3/16 -24 x 14 mm washer head screws and fiber washers to secure the blade to the blade holder. (Figure 1)
   • CAUTION: Do not connect fan blades until the fan is completely installed. Installing the fan with blades assembled may result in damage to the fan blades.
2. Secure the blade holders to the bottom of the motor assembly using the 1/4″-20 x 14 mm screws. (Figure 2)
   • NOTE: Periodically check blade holder hardware and resecure if necessary.

WARNING

• To reduce the risk of personal injury, do not bend the blade holders when installing, balancing the blades or cleaning the fan. Do not insert foreign objects in between the rotating blades.

CAUTION

• To reduce the risk of electric shock, disconnect the electrical supply circult to the fan before installing light kit.

How to Assemble the Light Kit

1. Remove one of the three screws in the support bracket at the bottom of the motor assembly. Slightly loosen the remaining two screws. Assemble the light plate assembly to the support bracket using the two key slots in the light plate. Replace the third screw and securely tighten all three screws. (Figure 1)
2. Remove one of the three screws in the light plate assembly. Slightly loosen the remaining two screws.(Figure 2)
3. Connect the 2 single-pin connectors from the socket plate assembly to the 2 single-pin connectors from motor assembly. (Figure 3)
4. Assemble the socket plate assembly to the light plate assembly using the previously removed screws. (Figure 4)
5. (Option A–for use with light kit)
   • Insert light bulb into socket. (Figure 5A)
   • CAUTION: To reduce the risk of fire, use 100-watt max. type T4-minican JD E11 tungsten halogen bulb. Turn off the wall switch and allow the bulb to cool for 10 minutes before relamping.
   • Bulb is pressurized and may shatter. DO NOT TOUCH BULB WITH BARE HANDS. Fingerprints may result in shorter bulb life. Remove fingerprints with alcohol prior to use.
   • 5 (Option B–for use with steel cap)
   • If you want to install the steel cap and not the light kit.
   • Assemble the steel cap to the light plate assembly by twisting in a clockwise direction. (Figure 5B)
   • NOTE: If you have installed your fan with the steel cap, skip steps 5.
6. Secure the glass to light plate assembly by twisting in a clockwise direction. Do not over-tighten. (Figure 6)

How to Operate Your Ceiling Fan

1. Operating and using hand-held remote (Figure 1): Install two 3-volt batteries (included). If not using for long periods of time, remove battery to prevent damage to transmitter. Store the hand-held remote away from excess heat or humidity.

• Hi – high fan speed
• Med – medium fan speed
• Low – low fan speed
• Rev – toggles airflow direction
• – fan off
• Light – on/off

How to Install Your Remote Control

How to Install Your Remote Control (Option #1)

1. Unthread two screws from the wall switch plate. (Figure 1)
2. Install the control bracket with two #6-32x 3/4” screws. Push the four plastic plugs in to cover the screw holes. (Included in the control packaging). (Figure 2)

How to Install Your Remote Control (Option #2)

1. Unthread two screws from the wall switch plate. (Figure 1)
2. Install the control bracket with two #6-32x 1” screws. Push the four plastic plugs in to cover the screw holes. (Included in the control packaging). (Figure 2)

How to Install Your Remote Control (Option #3)

1. Drill the two 1/4” holes in wall and use the M6 plastic anchor pushed into the holes. Install the control bracket with two #3- 1” self tap screws. Push the four plastic plugs in to cover the screw holes. (Included in the control packaging). (Figure 1)

Maintenance

• Periodic cleaning of your new ceiling fan is the only maintenance that is needed.
• When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish.
• Abrasive cleaning agents are not required and should be avoided to prevent damage to finish.

_ CAUTION: _Do not use water when cleaning your ceiling fan. It could damage the motor or the finish and create the possibility of electrical shock.

Blade Cleaning

• Periodic light dusting of the blades is recommended.
• A feather duster will work best.
• Avoid using water, cleansers, or harsh rags, which can warp and ruin the finish.

Trouble Shooting

WARNING: For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.

2. Loose power line connections to the fan, or loose switch wire connections in the switch housing.

3. Dead battery in remote control.

| 1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in the switch housings.

CAUTION: Make sure main power is turned off !

3. Replace with fresh battery.

2. FAN SOUNDS NOISY| 1. Blades not attached to fan.

2. Loose screws in motor housing.

3. Screws securing fan blade to blade arm with holder are loose.

4. Wire connectors inside housing rattling.

5. Motor noise caused by solid state variable speed control.

| 1. Attach blades to fan before operating.

2. Check to make sure all screws in motor housing are snug (not over- tight).

3. Check to make sure the screws which attach the fan blade to the blade arm with holder are tight.

4. Check to make sure wire connectors in motor housing are not rattling against each other or against the interior wall of the housing.

CAUTION: Make sure main power is turned off !

5. Some fan motors are sensitive to signals from

solid-state variable speed controls. Solid-state controls are not recommended, choose an alternative control method.

3. FAN WOBBLES EXCESSIVELY| 1. Screws securing fan blade holders to motor hub are loose.

2. Blade holders not seated properly.

3. Hanger bracket and/or ceiling outlet box is not securely fastened.

| 1. Check to be sure screws which attach the fan blade holders to the flywheel are tight.

2. Check to be sure the fan blade holders seat firmly and uniformly to the surface of the motor housing.

If holders are seated incorrectly, loosen the screws and retighten.

3. Tighten the hanger bracket screws to the outlet box, and secure outlet box.

Parts List

Model #FPS7981**

12

| Hardware Bags Containing:|

Wire Connectors (4)
Blade Holder Mounting Hardware Bag Containing

Blade Mounting Hardware Bag Containing
3/16

Exploded-View

FPS7981**

NOTE: The illustration shown is not to scale or its actual configuration or finishes may vary.

Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging materials, be certain all parts have been removed

How To Order Parts

Contact your retail store for repair parts.
When ordering repair parts, always give the following information.

• Part Number
• Part Description
• Fan Model Number

Contact

• 10983 Bennett Parkway Zionsville, IN 46077
• Toll Free: 888-567-2055
• FAX: 866-482-5215
• Outside U.S. call: 317-733-4113
• Visit Our Website: www.fanimation.com

Copyright 2014 Fanimation

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>