Audiopipe APK-2500 Sound Quality Digital Monoblock Amplifier Owner’s Manual
- June 13, 2024
- Audiopipe
Table of Contents
Audiopipe APK-2500 Sound Quality Digital Monoblock Amplifier Owner's Manual
INTRODUCTION
Congratulations and thank you for purchasing Audiopipe amplifier, the logical
choice in mobile audio amplification. Audiopipe products have been designed
and engineered with the highest quality components and top of the line
workmanship to help you reach the superior sound you are after.
To achieve optimal performance of your system, please take a few moments to
read over this manual if needed before starting your installation.
DESIGN FEATURES
- 1ohm stable Highly efficient and powerful digital monoblock.
- Strappable 2 mono block amps to 2 ohm
- High purity copper trace circuit boards.
- 0 gauge power / ground terminals
- Hand-wound high grade power supply
- 24dB low pass and subsonic filter
- The most safe protection circuits are applied to protect the amplifiers and audio systems.
- Thermal protection
- DC offset
- Speaker short protection
- Low & High battery voltage protection circuit
SPECIFICATIONS
1ohm stable digital monoblock amplifiers
Two amplifiers strappable to 2ohm
Frequency response : 10Hz ~ 270Hz
Signal to Noise Ratio : 95dB
Damping Factor : 200 <
Input sensitivity : 6V ~ 0.2V
Low pass filter : 35Hz ~ 250Hz @ 24dB / Oct
Subsonic filter : 10Hz ~ 50Hz @ 24dB / Oct
Bass Boost : 0 ~ 9dB @ 45Hz
Phase : 0 ~ 180 degree
Master/slave connection ( Strappable to 2ohm )
Remote level control is included
0 gauge power & ground terminals.
Working Voltage : APK-2500 ( 8.5V~16V ), APK-3500, APK-4500 & APK-5000 (
8.5V~18V )
External fuse rating ( strappable ) : APK-2500 : 200A ( 400A ) , APK-3500 :
350A ( 700A )
APK-4500 : 400A ( 800A ), APK-5500 : 450A ( 900A )
MAX OUTPUT POWER AT 1OHM.
APK-2500 : 2500Watts ( 2ohm strappable : 5000Watts )
APK-3500 : 3500Watts ( 2ohm strappable : 7000Watts )
APK-4500 : 4500Watts ( 2ohm strappable : 9000Watts )
APK-5500 : 5500Watts ( 2ohm strappable : 11000Watts )
CONTROLS & CONNECTIONS
SPEAKER CONNECTION
This terminal connects amplifiers to the speakers . Minimum speaker cable should be 12 gauge or larger. Connect the subwoofer speakers by checking the impedance 1 ohm for single unit or 2 ohm for strappable connection.
LINK CONNECTION
INPUT CONNECTION ;
Step 1. Connect the master amplifier to the head-unit and set its output
master / input slave switch to output master.
Step 2. Set slave amplifier output master / input slave switch to slave input.
Step 3. Connect RCA cable from the master to slave amplifier as shown in the
diagram.
POWER & SPEAKER CONNECTION ;
Step 1. Connect speaker cable ( + ) on master amp to subwoofer ( + )
Step 2. Connect speaker cable ( + ) on slave amp to subwoofer ( )
Step 3. Connect speaker cable ( ) on master amp to speaker cable ( ) on slave
amp
SLAVE AMPLIFIER
TROUBLE SHOOTING
NO SOUND ( NO OUTPUT )
- Please check all connections, cables’ rounting, short & voltage
- Please check the fuses , If they are blown, please replace with new one.
- Please check whether speakers work well, you can test speakers by connecting to another amplifier
PROTECTION
-
Please check overload, overheat ( thermal ), short and voltage, DC offset.
-
Minimum working impedance is 1 ohm for all amplifiers as single unit. and 2 ohm stable for strapped operation.
-
If amplifiers are shut down due to heat, they will be on some minutes later after cooling down. Please make better airflow and no obstruction around amplifiers for thermal protection
-
APK-2500 working voltage is 8.5V ~ 16V.
APK-3500, APK-4500 AND APK-5000’s working voltage is 8.5V ~ 18V -
When over 4V DC comes into amplifiers, then, they will be DC protected.
Check whether amplifiers work after removing RCA-Input.
If amplifiers work, then check DC by checking RCA-input .
When DC is over 4V at input, try by replacing +12V source unit .
DISTORTION & NOISE
- Readjust input level and check the speaker quality at another amplifier
- Replace poor quality speakers with good quality ones
- Check amplifiers and headunit’s ground contact. all grounds should be common.
- Check Rca Jack, then repalce with new one or reroute Rca Jack.
- Engine noise is caused by poor grounding of amplifiers, headunit, other components, battery or alternator, so please check all grounding connection.
POOR BASS RESPONSE
- Please check speaker cables and reverse polarity.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>