TARAMPS THS 6000 Multi-Channel Receiver Instruction Manual

TARAMPS THS 6000 Multi-Channel Receiver

Introduction

Congratulations on purchasing a Taramps product. Developed in a modern laboratory, with the highest technology and highly qualified professionals. This manual explains all the resources, operations, and guidelines for resolving questions that may arise in your installation. Take time to read it carefully and ensure the proper installation and use of all the benefits that this product can offer. In case of doubt even after reading this manual, please contact our technical support at the number +55 18 3266 4050 or our website at www.taramps.com.br.

Presentation

The TARAMPS THS 6000 is a Multi-Channel Receiver developed with high technology to integrate different environments. Compact and powerful it can be used in several applications providing quality sound.

Application examples

• Environment sounds for stores, shops, and clinics. It also allows, through the microphone input, warnings to be transmitted via the sound system.
• In your leisure area, gourmet space, country house, etc. Including various audio input options, such as Bluetooth, AUX, and USB, it allows the audio sources to be easily changed giving the user flexibility in choosing the preferred audio.
• The equipment is an automatic bolt and can be connected to any power plug between 90 and 240V. It has a switching power supply that is more efficient in the consumption of electricity.
• If you are not going to use the product for a long time, we recommend that you disconnect from the power plug.

Important recommendations

• The THS 6000 must be installed in a firm and ventilated place, away from heat and humidity places. Avoid locations with direct sunlight.
• Do not block the ventilation holes on the top and rear.
• Avoid falls and impacts.
• Carefully observe the polarity and impedance of the loudspeakers.
• Use cables according to the distance between the THS 6000 and the loudspeakers.
• The table below shows recommended gauges according to the distances
• In case of unwanted noise make sure that the cables and connections are in good condition.
• Leave the volume to a minimum of unused channels.

Audio source
The TARAMPS THS 6000 has the following audio inputs:

1. USB: Flash drive input *
2. MICRO SD CARD*
3. AUX (front): P2 standard auxiliary input.
4. AUX1 and AUX2: RCA standard auxiliary inputs.
5. BLUETOOTH
6. FM radio
7. Microphone input (standard P10)
8. Optical Input

The connected device must contain music in MP3 format to be identified by the equipment. Maximum supported size: 64GB. We advise you to always have a good antivirus, so there are no problems with the Flash Drive or micro SD card when connecting to the product. Infected devices may cause undesirable effects to the THS6000, such as Slow music reading and general failures. Do not use the USB input to connect to the computer or to recharge other devices that have batteries.

Package content

• 01 Multi Channel Receiver THS 6000
• 01 Remote Control
• 01 Optical Cable

Knowing your equipment
Front Panel

1. MICRO SD: Micro SD memory card input . shows, with the terminals facing up (The card must be positioned as the image

2. USB: Input to Flash Drive.

3. Aux. (Connector P2): Receives audio signal from the P2 output of your phone, tablet, MP3, or computer, among others. Use good quality cable to avoid unwanted noise.

4. ShortTouch (Track-): Rewind the music tracks in the USB/SD/BLUETOOTH. Long Touch (Volume -): Reduce the volume in all source options.
   FM: Short Touch: Reduce 0.1MHz of the frequency. Long: Automatic search to previous stations.

5. ShortTouch (Play /Pause): Pause or start the music on USB / SD / BLUETOOTH.
   Short Touch: Mute for AUXILIARY option
   FM: Short Touch: Advances next saved memory position of FM stations. Long: Searches for FM stations and saves them in memory.

6. Short Touch: (Track+): Forward the music tracks in the USB/SD/ BLUETOOTH.
   Long Touch:(Volume +): Increase the volume in all source options
   FM: Short Touch: Increase by 0.1 MHz of the frequency. Long: Automatic search to next stations.

7. Short Touch (MODE): Changes the source options, such as USB / SD / AUXILIAR / BLUETOOTH /FM.
   Long Touch – To turn off the device. (The device will stay in standby mode)

8. LED Display – Remote control I sensor: For better communication between the remote control and the device, point the control at this point on the display. Knowing your equipment Front Panel (sequence)

9. AUX1/OPTICAL or AUX2 KEY: Button pressed: Selects AUX1 and Optical inputs.
   Button not pressed: Select the AUX 2 input. (Inputs on the rear panel).

10. ATT: LED audio attenuation indicator. When identifying an audio signal from the microphone input or emitting the ding-dong signal (GONGO), the equipment attenuates the output signal, allowing higher
    evidence of the microphone. After 2 seconds without using the microphone, it returns to the state without attenuation. It is possible to enable or disable this function. With the device in standby mode, press and hold the gong key for 5 seconds. The ATTLED will flash 3x with the function enabled or 1 with the function disabled.

11.  MASTER: Controls the global volume level and must be used to adjust the output power desirable.

12. MIC: P10 input for a microphone.
    Microphone Recommendations:

    • The microphone signal has a low amplitude, so improper use can cause unwanted noise.
    • Use quality cables and connectors.
    • Do not wrap the microphone cables.
    • Do not pass the microphone in front of the loudspeakers. This causes feedback.

13. MIC: Adjust the volume of the microphone and the GONGO (ding-dong). If you do not use the microphone and GONGO, it is recommended to keep the volume to a minimum.

14. GONGO: GONGO activation key.

    • The product has 3 GONGO options. To select another option with the device on, press and hold the “GONGO” key.
    • The 3 gong patterns will be emitted in sequence (do not release the key). T
    • o select an option, and release the “GONGO” key after hearing the desired option.

15. EQUALIZATION: 3 band equalizer control.

    • LOW: Bass frequencies
    • MID: Middle frequencies
    • HIGH: High frequencies.

16. CHL/CH R: Adjust each channel level (Lou R).

17. LED STAND-BY: On, indicates that the product is plugged into the outlet in standby mode

18. TECLA ON/STB: Turn ON the receiver or stay in standby mode.

Mix Mode
To enable the Mix Mode, slide the switch key under the device to the ON position. For this use a small screwdriver and keep the power cord unplugged. In mixed mode, the 2 outputs have the same sound, (no longer being stereo Land R allowing, for example, the distribution of the sound over 2 different rooms without channeling.

Protection System

The THS 6000 has a protection system against output overload and output short circuits. When the protections are activated, the STAND BY LED on the front panel turns on temporarily and the audio output is interrupted. About 2 seconds or the audio is restored. If the protection system or system meets frequently, review the settings and installation of your system

Knowing your equipment Rear Panel

1. POWER CABLE: Plugged it into a powered outlet. This product operates from 127V AC to 220V AC.

2. SPEAKER OUT: To connect the loudspeakers. Follow the indicated polarity and the recommended minimum impedance of 4 ohms for each channel.

3. OUT: LINE OUT: The LINE OUT output allows to send the audio signal (not amplified) to other equipment, such as another THS 4600, an amplifier, or an active subwoofer. The LINE OUT sound is affected by the 3 Band Equalizer and Volume controls. (LOW, MID, HIGH, and VOLUME controllers).

4. INPUT AUX 1, OPTICAL e AUX 2: Audio inputs. Use the frontal key to select. Using the Optical function, you can count on the AUTO TURN ON system. With this option enabled, the device is automatically turned on when it recognizes the audio on the optical input. It is possible to enable or disable this function. To do this, press and hold the ON / STB key for 5 seconds. The standby LED will flash 3x for the enabled function and 2x for the disabled function. (It is enabled by default). Check the page 18 (Example of use OPTICAL input).
   Note: The OPTICAL input is shared with the AUX 1 input, which means that is not possible to use both simultaneously. In the case of televisions, audio configuration for standard OPTICAL PCM output may be required, configured in the menu of the TV itself. (Check your TV manufacturer’s manual).

5. FM ANTENNA: Indoor wire antenna for FM radio reception. Position the wire antenna in order to achieve the best FM reception.

Remote Control Function
THS 6000 has a compact remote control, so you can remotely control the device with practicality

ON /OFF: Press the key to turn off the device.

MODE: Switch the audio source (USB, BLUETOOTH, SD, AUXILIARY, FM).

MUTE

PLAY / PAUSE: Pause or start the music to USB/SD / BLUETOOTH.

• FM: Short Press: Advances next saved memory location of FM stations.
• Long Press: Searches for FM stations and saves them in memory.

TRACK – Previous track (short press)

• FOLDER – Previous folder (long press)
• FM: Short Press: Previous 0.1MHz of the frequency.
• Long Press: Automatic search to the previous station.

TRACK + Next track (short press)

• FOLDER + Next folder (long press)
• FM: Short Press: Next 0.1MHz of the frequency.
• Long Press: Automatic search to the next station.

EQUALIZATION: Pop/ Rock / Jazz/ Country/ Normal.

• Do not work in auxiliary mode.
• FM: Short Press Return to the saved memory position of FM stations.

VOL-: Volume down

VOL+: Volume up

REPEAT: Repeat/play MP3 options

USD U/SD: Switch mode between USB/SD Card

• FM: Searches for FM stations and saves them in memory.
• NUMERIC KEYBOARD:FM: Long Press saves FM stations.

Bluetooth
When selecting the Bluetooth function (identified with “bt” on the display), the THS 6000 waits for a Bluetooth connection. Search for the device called “TARAMPS THS 6000” using your phone, tablet, PC, or other and match it. To connect to a new device, disconnect the current one and make the new Bluetooth pairing. Bluetooth specification: class Il with a 10m maximum range and may vary according to the environment (such as walls) and the connected device.

Bluetooth examples of use
Some TVs have an audio output system via Bluetooth. If your TV has this feature, it’s possible to transmit the audio to the THS 6000. Consult your TV manufacturer’s manual.

Example of using OPTIC input Select the AUX mode on the ‘MODE’ key and also press and hold the AUX 1 OPTICAL key

Example of using RCA input (AUX 2) Select the AUX mode on the ‘‘Key and the AUX 2 key not pressed

Connection examples – Wall sconces
Examples to until 16 loudspeakers 8 ohms each

For this kind of connection use cables with a minimum gauge of 1.5mm² for up to 40 meters. For long distances, consult the table on page 12 ‘‘ Important recommendations ’’. It’s necessary to make connections in parallel and series as shown in the example, to match impedance.

Term of warranty

Located at Rua Abílio Daguano, 274 Res. Manoel Martins – Alfredo Marcondes – SP, ZIPCODE 19.180-000, TARAMPS guarantees this product against defects in design, manufacture, assembly, and/or jointly due to design flaws that make it inappropriate or unsuitable for the intended use, for a period of 12 months from the date of acquisition. In case of a defect in the warranty period, TARAMPS is responsible for the repair or replacement of the device manufactured by it.

This warranty excludes

• Products damaged by improper installation, water infiltration, and violation by unauthorized persons;
• Torn or torn warranty seal;
• Cases where the product is not used under normal conditions;
• Defects caused by accessories, modifications or equipment attached to the product;
• The product shows damage due to falls, impacts or the action of agents of nature (floods, lightning, etc.);
• Costs of removing and reinstalling the equipment, as well as transporting it to the technical assistance station;
• Damage of any nature, resulting from product problems, as well as losses caused by interruption of use.

Technical assistance
We have technical assistance all over Brazil and we are always ready to answer your questions and needs. To locate an electronic Taramps technical assistance near you, access our website:  www.taramps.com.br/pt/rede-de-assistances- technical or contact the factory technical assistance department:

Taramps Electronics
Rua Abílio Daguano, n 274
ZIPCODE: 19.180-000
Phones + 55 183266-4050/+55 18 99749-3391
E-mail: service@taramps.com.br

Technical features
Nominal power with 1 KHz sinusoidal signal and 4 ohms resistive load. (Measured according to ABNT BR IC 60268-3 sound equipment, Part 3: Amplifiers). Protection system on page 15. The values mentioned are typical and may change due to the tolerance of components or the manufacturing process. For more information or questions visit our website or contact TARAMPS support. Taramps reserves the right to modify the contents of this manual without prior notice and not to apply the modifications to units previously produced.

Fabricado por / Manufactured by
TARAMPS ELECTRONICS LTDA
CNPJ/TAX ID: 11.273.485/0001-03
R. João Silvério, 121  Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br www.taramps.com.br

References

• Taramps

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>