3SI UTV POLGEN-DRH-3SI Polaris General Door Rear Window Combo Instruction Manual

3SI UTV POLGEN-DRH-3SI Polaris General Door Rear Window Combo

Product Information

Specifications:

• Manufacturer: 3SI UTV
• Material: Heavy-duty fabric
• Features: Water repellent, mildew resistant, UV resistant,abrasion resistant
• Compatibility: Designed for specific UTV models

Product Usage Instructions

Installation:

1. Ensure the adhesive hook is applied at a temperature of 60 degrees or above.
2. Clean surfaces where the adhesive hook will be attached with mild soap and water. Do not use wax or compounds that leave a slick surface.
3. Properly fit the enclosure to the cab frame ensuring a snug and square fit.
4. Periodically clean the enclosure with mild soap and water to prevent dirt buildup.
5. Clean vinyl windows with mild soap, water, and a soft cloth. Avoid detergents, window cleaners, solvents, or chemicals.
6. Before storing, clean and dry the enclosure. Roll it instead of folding to prevent creases in vinyl windows.
7. Enclosures suitable for hauling are Lexan windshields, full cab enclosures, and door/rear window combos with top and windshield installed. Securely tie down before hauling and do not exceed 55 mph.

Detailed Instructions:
Follow the step-by-step installation instructions provided with your specific model enclosure. Install the modular cab system components in the prescribed order: Back Panel, Door Panels, Windshield/Top or Top.

Frequently Asked Questions (FAQ):

Q: Can I use any cleaning agents on the vinyl windows?
A: No, only clean the vinyl windows with mild soap, water, and a soft cloth. Avoid using detergents, window cleaners, solvents, or chemicals.

Q: How should I store the enclosure when not in use?
A: Do not fold the enclosure for storage. Roll it up to avoid creasing the vinyl windows.

Installation Instructions

Thank you for purchasing a UTV enclosure manufactured in the USA with pride by 3SI UTV. Your enclosure is made of heavy duty fabric that is water repellent and resistant to mildew, ultra-violet rays and abrasion. With proper installation and care you can expect many years of service from your 3SI UTV enclosure.

SOME IMPORTANT NOTES BEFORE GETTING STARTED….

• The enclosure attaches to your UTV’s cab frame with Velcro. The technical term for Velcro is hook and loop. Loop is the soft side and hook, the rough side. Loop has been sewn into the enclosure at various points. Adhesive hook has been supplied to attach to your cab frame, corresponding to the sewn-in loop. If you struggle with placement of the adhesive hook, with the enclosure held to the cab frame, note the locations of the sewn-in loop. The adhesive hook is attached to the cab frame at those locations.
• The adhesive hook should be applied at a temperature of 60 degrees or above. For maximum adhesion, when the adhesive hook is in place, allow the adhesive to cure for 24 hours before attaching the loop to the hook.
• Clean the surfaces the adhesive hook will be attached to before beginning installation. A light cleaning with mild soap and water is best. A little Windex works great. Do NOT wax or clean with a compound that leaves the frame slick. The adhesive hook will not stick to a slick surface. Again, a light cleaning is best.
• Your enclosure is not a “one size fits all” product. The enclosure was designed and manufactured specifically for your model UTV. As a result, the enclosure should fit square and snug to the cab frame.
• Periodic cleaning of your enclosure with mild soap and water is recommended to minimize accumulations of dirt.
• Clean the vinyl windows with mild soap, water, and a soft cloth to avoid scratches. DO NOT USE ANY DETERGENTS,WINDOW CLEANERS, SOLVENTS OR CHEMICALS TO CLEAN VINYL WINDOWS.
• Clean your enclosure and allow it to dry before removing for storage. Never fold your enclosure to store. Roll the enclosure to avoid creasing the vinyl windows. Creases in the vinyl windows cannot be removed. CREASING THE VINYL WINDOWS VOIDS ALL WARRANTIES AND GUARANTEES.
• The only enclosures manufactured by 3SI UTV that can be hauled when installed are Lexan windshields, full cab enclosures, and door/rear window combos with top and windshield installed. However, the enclosures should be tied down before hauling. Speed should not exceed 55 mph while hauling to prevent ripping and shredding of the material and zippers. REMOVE ALL OTHER ENCLOSURES BEFORE HAULING.

PLEASE READ AND FOLLOW THE DETAILED INSTRUCTIONS THAT ARE ATTACHED.

Polaris General Door/Rear Window

Installation Instructions
You have just purchased the best Enclosure for your Utility Terrain Vehicle available on the market today. Your Enclosure is made of Heavy Duty Fabric that is Water Repellent and resistant to Mildew, Ultra-Violet Sun Rays and Abrasion. With proper installation and care you can expect many years of long lasting fit, color and service life from your 3SI UTV Cab Enclosure.

Step 1: Remove your Adhesive Hook Kit, Back Panel, and Door Panels from the shipping box. The enclosures for the Polaris General are modular. Our modular cab system allows you to determine your level of coverage. When warm, just a windshield and top will do. Later add the back panel. When full coverage is needed, add doors. The modular cab system should be installed in the following order:

• Back Panel
• Door Panels
• Windshield/Top or Top

Step 2: Remove your windshield and hard top.

Step 3: As each panel is to be installed, hold the panel to the cab frame. Note the location of sewn-in loop strips in the enclosure. Adhesive hook strips will be attached to the cab frame corresponding to the loop strips. Remove the backing from the adhesive hook strips and install as indicated in the following adhesive hook table and pictures.

Adhesive Hook Kit Contents/Placement

REAR PANEL
A| 1-48”| Attach horizontally to the inside edge of the rear cross bar. Wrap the top of the rear panel around the cross bar. Attach the sewn-in loop at the top of the rear panel to the adhesive hook strip.
B| 2-4”| Attach vertically to the outside edge of the rear roll bar uprights corresponding to the double-sided hook and loop straps at the
| | top/sides of the rear panel. Wrap the double-sided hook and loop straps around the roll bar.
---|---|---

C

|

2-10”

| Attach vertically to the outside edge of the rear roll bar uprights corresponding to the 10” webbing/loop tabs at the sides of the rear panel. Use the tabs to pull the rear panel tight from side to side. Attach the sewn-in loop in the tabs to the adhesive hook strips.

D

|

2-3”

| Attach vertically to the outside edge of the rear roll bar uprights corresponding to the 3” webbing/loop tabs at the sides of the rear panel. Use the tabs to pull the rear panel tight from side to side. Attach the sewn-in loop in the tabs to the adhesive hook strips.

No Ref

|

2-20”

| Attach horizontally to the body behind the seats corresponding to the sewn- in loop strips at the bottom of the rear panel. Attach the sewn- in loop strips to the adhesive hook strips.
DOOR PANELS
A| 2-12”| Attach horizontally to the inside edge of the side roll bars. The 12” webbing/loop tab attaches to the adhesive hook strip.
B| 2-6”| Attach to the top of the front roof bracket. The sewn-in loop on the 6” flap attached to the adhesive hook strip.
C| 2-4”| Attach to the front/side of the roof bracket. The sewn-in loop on the 6” flap attached to the adhesive hook strip.
D| 2-10”| Attach vertically to the inside edge of the front roll bar. The sewn-in loop along the front of the door panels attach to the adhesive hook strip.
E| 2-3”| Attach to the flat plastic beside the bolt at bottom of front roll bar. Attach the sewn-in loop on the edge of the 3” flap to the adhesive hook strip.
F| 2-5”| USE THE ADHESIVE HOOK STRIPS ONLY IF THE BACK PANEL IS NOT INSTALLED. Attach horizontally to the inside edge of the side roll bars in the curve at the back of the side roll bars. The 5” webbing/loop tab attaches to the adhesive hook strip. IF THE BACK PANEL IS INSTALLED, ATTACH TO THE EXPOSED HOOK ALONG THE EDGE OF THE REAR PANEL.
G| 2-3”| USE THE ADHESIVE HOOK STRIPS ONLY IF THE BACK PANEL IS NOT INSTALLED. Attach vertically to the back/top side of the rear roll bar uprights corresponding to the 3” sewn-in loop just above the door zipper. The 3” sewn- in loop attaches to the adhesive hook strip. IF THE BACK PANEL IS INSTALLED, ATTACH TO THE EXPOSED HOOK ALONG THE EDGE OF THE REAR PANEL.
H| 2-15”| USE THE ADHESIVE HOOK STRIPS ONLY IF THE BACK PANEL IS NOT INSTALLED. Attach vertically to the back side of the rear roll bar uprights corresponding to the 15” sewn-in loop just below the door zipper. The 15” sewn-in loop strip attaches to the adhesive hook strip. IF THE BACK PANEL IS INSTALLED, ATTACH TO THE EXPOSED HOOK ALONG THE EDGE OF THE REAR PANEL.
---|---|---
I| 2-5”| USE THE ADHESIVE HOOK STRIPS ONLY IF THE BACK PANEL IS NOT INSTALLED. Attach vertically to the back/bottom of the rear roll bar uprights corresponding to the 5” sewn-in loop. The 5” sewn-in loop strip attaches to the adhesive hook strip. IF THE BACK PANEL IS INSTALLED, ATTACH TO THE EXPOSED HOOK ALONG THE EDGE OF THE REAR PANEL.
J| 2-6”| Attach diagonally to the outside of the door panel corresponding to the 6” sewn-in loop strip on the back side of the bottom door panel. The 6” sewn-in loop strip attaches to the adhesive hook strip.
K| 2-30”| Attach horizontally to the outside of the door panel corresponding to the 30” sewn-in loop strip on the bottom of the door panel. The 30” sewn-in loop strip attaches to the adhesive hook strip.
L| 2-5”| Attach vertically to the body corresponding to the sewn-in loop along the back edge of the lower door panel.
M| 2-6”| Attach vertically to the front of the door panel corresponding to the sewn-in loop strip at the front of the bottom door panel. The 6” sewn- in loop strip attaches to the adhesive hook strip.

Step 4: After all adhesive hook strips are attached, begin attaching the enclosure to the cab frame. As you attach the hook and loop, square each panel to the frame. PLEASE NOTE, FOR MAXIMUM ADHESION, ALLOW THE ADHESIVE HOOK TO ADHERE TO THE FRAME FOR 24 HOURS BEFORE PULLING AGAINST THE HOOK WITH THE LOOP STRIPS.

Step 5: Wrap the double-sided strap at the bottom of the V on the back side of the door to the corresponding bar. The location is shown below.

Step 6: If the front tab needs to be cut to accommodate windshield clamps, please use the following instructions.

Step 7: Repeat any steps necessary to achieve a snug fit on the cab frame.

See enclosed Product Care sheet for instructions on how to properly care for your 3SI UTV Enclosure.

Care Instructions

Heavy Duty Marine and Mil-Spec Military Fabric Cleaning All 3SI UTV Enclosure Heavy Duty Marine and Military Camo fabrics are guaranteed against excessive loss of color or strength under normal exposure and use conditions. Periodic cleaning with a solution of 4 ounces of bleach and 2 ounces of soap (NOT DETERGENTS) in one gallon of water is recommended to minimize accumulations of dirt, bird droppings and other contaminants which can support surface mildew and stain fabric.

Soft Vinyl Window Cleaning
3SI UTV Enclosure Vinyl Windows will remain clear and provide great visibility under normal exposure conditions if properly cleaned. Periodic cleaning with a solution of 1 ounce of soap in one gallon of water is all that is needed to maintain good window cleanliness and visibility. Caution: DO NOT USE ANY DETERGENTS,WINDOW CLEANERS, SOLVENTS or CHEMICALS OF ANY KIND TO CLEAN VINYL WINDOWS AS THESE WILL CLOUD THE WINDOWS. ALSO, NEVER RUB WINDOWS WITH A DRY CLOTH OR RAG.

Storage Recommendations
Before removing the 3SI UTV Enclosure from your vehicle for storage, clean the Fabric and Vinyl Windows thoroughly as indicated above. Any dirt remaining on the Enclosure may scratch Vinyl Windows while in storage. Once the Enclosure has been cleaned it should be placed on a large flat surface. Lay the Enclosure out so that Vinyl Windows are in a flat position. Fold the doors over the rear panel first then fold the top and windshield on top of the doors keeping the Vinyl Windows flat. Caution: FOLDING VINYL WINDOWS WILL CAUSE PERMANENT CREASE DAMAGE AND WILL VOID ALL WARRANTIES. Once the Enclosure is folded keeping all Vinyl Windows flat, begin rolling the Enclosure into an 8” roll. Place the 8” roll into a box and store at normal room temperature. To ensure long life of your enclosure it is best not to store in extreme temperatures.

Hauling
The ONLY products manufactured by 3SI UTV that can be hauled while installed are the hard windshields, full cab enclosures, and door/rear window combos with top and windshield installed. However, the full cab enclosures and door/rear window combos should be tied down before hauling. Speed should not exceed 55 mph while hauling to prevent ripping and shredding of the material and zippers.

NEVER HAUL INSTALLED SOFT TOPS, WINDSHIELD TOP COMBOS, AND SUMMER CABS. REMOVE BEFORE HAULING.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>