TARAMPS DS 800X4 Amplifier User Manual
- June 13, 2024
- TARAMPS
Table of Contents
TARAMPS DS 800X4 Amplifier
Product Information
The product is a Taramps Electronics LTDA amplifier with the following specifications:
- Power Output: 4 x 200W RMS
- Supported Ohm Ratings: 1 ohm, 2 ohms, 4 ohms
- Product Family: Standard for aftermarket electronic equipment in vehicles
- Dimensions: 173 x 52 x 227mm
- Weight: 1.43kg
The amplifier features a built-in crossover and LED indicator.
Product Usage Instructions
To use the amplifier, follow these steps:
- Before connecting the amplifier, ensure that the negative (-) terminal of the power source is disconnected to prevent any electrical damage.
- Choose the appropriate ohm rating based on your setup:
- For a 1 ohm setup, connect the amplifier accordingly.
- For a 2 ohm setup, connect the amplifier accordingly.
- For a 4 ohm setup, connect the amplifier accordingly.
- Connect your subwoofer or woofer to the amplifier using the recommended cables.
- If using a CD/DVD player, connect it to the amplifier using an RCA cable.
- Make sure to use a suitable circuit breaker to protect the amplifier from excessive current.
- Ensure that the input voltage of the amplifier is between 9VDC and 16VDC.
Note: The images shown are for illustrative purposes only.
Term of warranty
TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.
This warranty excludes:
- Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
- Tamper or torn warranty seal;
- Cases in which the product is not used in adequate conditions;
- Defects caused by accessories, modifications or features attached to the product;
- The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
- Warranty card is not properly filled or torn;
- Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
- Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.
Technical assistance
For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias-
tecnicas or
contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br
Introduction
Read this manual before preparing the product. In case of doubt, contact our
technical support: (18) 3266-4050 or
www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in
household waste. Look for an electronic equipment collection or recycling
center for proper disposal.
Declaration of Conformity
TARAMPS ELECTRONICS LTDA
Alfredo Marcondes – SP
Brazil
Hereby, Taramps Electronics Ltda declares that the product DS 800X4 complies
with the Directive 2014/30/EU, according with the following harmonized
standard:
-EN 50498:2010 Electromagnetic compatibility (EMC) –
Product family standard for aftermarket electronic equipment in vehicles The
full text of the EU Declaration of Conformity is available at the following
Product Page on Internet.
Safety requirements
To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the WARNINGS and CAUTIONS contained here.
-
The installation of this amplifier must be done by a qualified professional.
-
Wear safety glasses, insulated gloves and correct tools for installing this product.
-
This amplifier is for use with 12V batteries. Always check the voltage before installing.
-
This amplifier must be installed in a firm place with at least 1″ space around the heatsink for proper heat spreading.
-
Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
-
Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
-
Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
-
Before make any connection to amplifier, disconnect the battery negative terminal.
-
When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.!
-
This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
-
Output connections for speakers may have voltage levels when the amplifier is operating.
Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals. -
If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.
-
Safety
As you read this manual, pay attention to the safety symbols. -
CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage. -
Taramps reserves the right to modify the contents of this document at any time without prior notice and does _ not have the obligation to apply the changes in units which were previously produced.
Functions & inputs
- INPUT: Inputs of signals to be amplified. Connect these signals to RCA outputs of Head Unit, using good quality shielded cables to avoid noise interference.
- LEVEL: It sets the amplifier input sensitivity, which allows an optimal adjustment to the output signals levels of nearly all models of Head Units found in the market.
- CROSSOVER: Set the operating mode of amplifier:
SELECTOR POSITION -FULL
Amplifies the whole audio range, responding from 10Hz to 22KHz. This function
is normally used when there is an external crossover in the system.
SELECTOR POSITION – HPF-(HIGH PASS)
Amplifies signals with more intensity above 90Hz. This type of function is
used mid-bass, mid-range speakers or tweeters.
SELECTOR POSITION – LPF – (LOW PASS)
Amplifies only bass signal, the response is limited to 90Hz (-12dB/8a), an
optimal frequency cutoff for sub- woofers.
WIRE HIGH LEVEL INPUT: Input for high level / low impedance signals (from
the speaker output of the players or multimedia center).
It features function of triggering through the input signal, so it eliminates
the use of the REMOTE IN wire from the power connector when using this input.
Note: The system is designed for use in virtually all multimedia head
units on the market. However, on some head units, you may not get the trigger
effect due to the type of audio output circuit. In this case, use the REMOTE
wire for triggering it normally.
LED indicator
ON: Indicates that amplifier is on.
Output & power supply connector
OUTPUT: To connect the speakers. Follow the polarity and the minimum
impedance recommended.
DS 800X4 (1 Ohm) – For STEREO connections, the minimum impedance is 1 ohm
at each channel; for BRIDE connections is 2 ohms.
DS 800X4 (2 Ohms) – For STEREO connections, the minimum impedance is 2
ohms at each channel; for BRIDE connections is 4 ohms.
To combine speakers, the resulting impedance must be taken in consideration.
See the examples below:
CAUTION: Due to the presence of voltage at the output terminals when the
product is turned on, avoid contact with them. Risk of electric shock.
POWER (Power Supply Connector): The connector terminal (+) must be
connected to the battery’s positive pole with a 10mm? (minimum) wire gauge.
The connector terminal (-) must be properly connect to the battery’s negative
pole with a same wire gauge. The remote terminal must be connected to the Head
Unit REMOTE output with a 0.75mm wire.
CAUTION :Before making any connections to the powerterminals, make sure
that the negative (4) of the vehicle battery is disconnected.
Protection system
Short-circuit Protection: Shutdown the amplifier when detect a short-
circuit or impedance lower than the supported at the output.
Installation
CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.
Recommended wire gauge & fuse
Positive / negative power supply cable. 7 AWG
Output cables wire gauge 15 AWG
Remote cable 18 AWG
Protection fuse or circuit breaker 60A
Calculated considering a maximum length of 4m. Distance greater than this, you
will need to increase the cable gauges.
CAUTION : Using wire gauges below the recommendation will result in power
loss and overheating of wiring.
Check polarity and never reverse power supply cables due to the risk of damage
to the amplifier. It is compulsory to install a protection fuses or circuit
breakers as close as possible from batteries.
Technical features
- Rated power with 60Hz to 1KHz sinusoidal signal and THD <= 1%, with resistive loads, measured with Audio Precision APx525 audio analyzer or equivalent and the product at lower than 50°C case temperature and 12.6V supply voltage.
- Frequency response measured at 4 ohms load, in 4 channels mode.
The values as above are typical and may vary, due to electronic components
tolerance or manufacturing process. For further informations or questions,
visit our website or contact TARAMPS support.
+55 18 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>