BEAUTIFLY Sonic Skin Scrubber User Manual

: June 13, 2024
: BEAUTIFLY

Table of Contents

BEAUTIFLY Sonic Skin Scrubber
Specification
QR SCAN
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEAUTIFLY Sonic Skin Scrubber

BEAUTIFL- Sonic-Skin-Scrubber-product

Specification

Ultrasound frequency: 27 kHz
Power: 1,SN
Output voltage: 3,2\
Power supply/ charging: battery I USS wire
Full charge time: 2 ,5h
Moisture protection: IPX5

Device components (see page 2, f1 J

Applicator lid
Water tank lid
Applicator
Mode and charging indicators
On/off button and mode control
Water inlet with a plug
USS cable
Pipettes for water

Modes

SPRAYING mode -water spraying. This mode acts as a facial moisturizer. The device turns the water into a light haze and does not leave any drops on the face. The water breaks down into small particles that are smaller than the pores on the skin, such particles quickly penetrate into the deeper layers of the skin, moisturizing il
PEELING+ SPRAYING mode-ultrasonic peeling+ water spraying Mode for ultrasonic peeling. In this mode, ultrasound and the water spray function work simultaneously. Ultrasonic peeling is an effective stimulating facial treatment for skin care at any age. The skin is gently and slowly exfoliated and cleansed without stretching or mechanical damage. In just a few sessions acne disappears, sebaceous glands function becomes normalized, the upper layer of the epidermis is renewed and the skin becomes noticeably softer and more elastic. The water spray function together with the peeling keeps the skin moisturized during the procedure.
PEELING mode-ultrasonic peeling Mode for ultrasonic peeling without water spray function.
LIFTING mode -sonophoresis/micromassage. Ultrasound makes the preparations more active. It improves the process of penetration of valuable nutrients into the deepest Layers of the skin, thereby multiplying the effectiveness of cosmetic products.
An ultrasound massage tones muscles, massages tissues at the cellular level, visibly rejuvenates the skin and tightens facial contours.

Device charging

Make sure to charge the device fully before the first use. Full charging of the device usually takes 2,5 hours (when it is completely discharged).
Make sure that the device is dry.
To charge the device, use the USB cable supplied with the device.
White charging, the first indicator will blink, then the second, then the third. When the device is fully charged, indicators stop blinking.
When the device discharges, the indicator light will blink, and then the device will turn off.
The duration of charging may vary depending on operating time and conditions.
During Longwtenn storage, the device will be discharged even without use. In this case, it is necessary to recharge the device at least monthly.
The battery charge lasts for 1,5 hours of continuous operation.
Warning! The device is not usable when being charged.

Control

Modes are controlled with one button.
To turn the device on and off, press and hold the button for 2 seconds.
To select the necessary mode, switch the button, and the indicator light will tell you which mode is selected.

Fill the tank with water
To use mode 1 and/or 2, you must fill the tank as follows:

Remove the applicator lid.
Then remove the water tank Lid. For this, slide the tank lid with your thumb toward the applicator until it clicks, and simply remove it
Remove the cap and fill it with water or liquid intended for cavitation with a special pipette. Close the plug.
Place the lid of the tank back on the device.
Warning! Do not fill the tank with Liquids other than water to avoid damage to the device.During the operation of the device, an acoustic signal is emitted every 3 minutes. This means that it is recommended to move on to the treatment of the next facial area.

Preparation

Before starting the procedure, it is necessary to remove impurities and makeup from the skin of the face and decollete.
To increase the effectiveness of the ultrasound procedure, you can prepare the skin with a Light scrub.
WOO< should be performed using a water-based gel/serum/lotion designed for ultrasound procedures. The main function of using cosmetics is that ultrasound increases the activity of drugs and enhances the penetration of valuable nutrients into the deepest layers of the skin. An important parameter is that the gel I serum I Lotion is an ideal conductor of ultrasonic waves.
Perform, is an ultrasonic deaning or sonophoresis procedure with progressive movements along the massage lines of the face, neck, and decol1ete.
After the procedure, it will be helpful to apply a face mask suitable for the skin type.

How to use

SPRAYING mode-water spraying
- Press and hold the power button for 2 seconds. The device will turn on and start spraying water.
- The indicator Light on this mode will blink.
- Direct a stream of water vapor onto your skin for a few seconds to moisturize it
  If the spray is weak, and there is not enough water, add water if necessary.
  Warning! Do not fill the tank with liquids other than water to avoid damage to the device.
PEELING + SPRAYING mode -ultrasonic peeling + water spraying
Mode for ultrasonic peeling. In this mode, ultrasound and the water spray function work simultaneously. The water sprays for 15 seconds, then stops for 5 seconds, then sprays again, etc.
- If the spray is weak, and there is not enough water, add water if necessary.
- Press the power button to select this mode.
- The indicator light in this mode will not blink but will be on and there will be a continuous treatment
- Perform, facial cleansing in the direction of the massage.
- Proper positioning of the device applicator during the ultrasonic facial cleansing procedure. The applicator is at an angle of 35-45° (see page 2, f3]
PEELING mode – ultrasonic peeling
Mode for ultrasonic peeling without water spray function.
- Press the power button to select this mode.
- The indicator Light in this mode will be on and there will be a continuous treatment.
- Perform facial dealing in the direction of the massage. (see page 2, f3]
- Proper positioning of the device applicator during the ultrasonic facial cleansing procedure. The applicator is at an angle of 35-45°
LIFTING mode- sonophoresis/micro-massage
- Press the power button to select this mode.
- The indicator Light in this mode will be on and the ultrasound will go into impulse function.
- Tum the device with the other side of the applicator and perform the sonophoresis procedure on the face in the direction of the massage.
- Lines are shown in the illustration. (see page 2, f4)
- Proper positioning of the device applicator during the sonophoresis procedure. The applicator is positioned backward at a 45° angle.

Warning

Do not use this device for purposes other than those mentioned in the user manual.
Tum off the device if it is not used. Do not use the device for a long time in one place. Moving the device too fast will affect its effectiveness.
Take away the use of the device for people with acute, chronic illness, fever, heart disease, pregnancy, facial surgery, skin rash, blood disease, during menstruation, people with pacemakers, and orthodontic accommodation.
Do not use the device around the pupil, eyelid, injured skin, mouth, and intimate parts of the body.
Please protect the device against physical impact.
Please use the device in accordance with these instructions. Damaged device, have it repaired.
Please keep the device away from dust, shocks, and hot or excessively cold environments.
If the packaging is damaged, before using it, please make sure that the device is working properly.
Keep the device out of the reach of children.
In case of malfunction, do not disassemble the device yourself.
Do not submerge the device in water, do not hold it under a stream of water – it is not waterproof.
Use only the USB cable supplied with the product.

Storage

Keep the device dry and dean.
Keep away from high temperatures.
Keep out of the reach of children.

Cleaning

Rinse the peeling spatula and wipe with a damp doth
Do not immerse the device in water for a long time.

More information about the product is available on the manufacturer’s website at:

Electrical and electronic devices, as well as batteries and accumulators, must not be mixed with other household waste. This is indicated by the crossed-out trash can symbol on the packaging. Used electrical and electronic devices, batteries, and accumulators must be taken to local selective waste collection points or to the retailer, and more information can be found in your municipality. Electrical and electronic equipment, batteries, and accumulators may contain hazardous substances, mixtures, and components harmful to the environment and human health. Improper handling or damage to them can lead to health hazards or environmental pollution during further disposal or recycling.

https://beautifly.eu/deklaracje