Xavax 112926 LED Plant Centre with Growth Light User Manual
- June 13, 2024
- xavax
Table of Contents
Xavax 112926 LED Plant Centre with Growth Light User Manual
Thank you for choosing a Xavax product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.
1. Explanation of warning symbols and notes
Risk of electric shock
This symbol indicates a risk of electric shock from touching uninsulated
product parts that may carry hazardous voltage.
⚠ Warning
This symbol is used to indicate safety instructions or to draw your attention
to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package contents
- Plant centre setup kit
- These operating instructions
3. Safety instructions
- Protect the product from dirt, moisture and overheating and use it in dry rooms only.
- This product is not intended for use by persons, including children, with limited physical, sensory or mental abilities or lacking in experience or knowledge, unless they are supervised by a person responsible for their safety or have been instructed on how to use the product.
- The product must only be operated on a supply network as described on the type plate.
- Do not drop the product and do not expose it to any major shocks.
- Do not open the device or continue to operate it if it becomes damaged.
- Do not immerse the power cable or the LED module in water or liquids.
- Beware of water. Only use plant pots without a drain hole or pots with saucers so that water does not collect under the light.
- The LED module should not come into contact with water during operation.
- The product is intended for private, non-commercial use only.
- Use the product only for the intended purpose.
- The product is intended only for use inside buildings.
- Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
- Only use the article under moderate climatic conditions.
- Do not operate the product outside the power limits given in the specifications.
- Do not use the product in areas in which electronic products are not permitted.
- Do not use the product in a damp environment and avoid splashing water.
- Do not modify the product in any way. Doing so voids the warranty.
- Dispose of packaging material immediately in accordance with the locally applicable regulations.
- Route all cables so there is no risk of tripping.
- Do not bend or crush the cable.
- Always pull directly on the plug when disconnecting the cable, never on the cable itself.
Risk of electric shock
- Do not open the device or continue to operate it if it becomes damaged.
- Do not use the product if the AC adapter, adapter cable or power cable is damaged.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Warning
Never look directly into the light source and do not shine the light beam
directly into the eyes of other persons or animals. Doing so can cause injury
of the eyes!
- Please note that lights (even LEDs) can generate heat and may become hot. Always let the LED module cool down for a few minutes before touching it.
- Do not place any objects on the light or hang any objects (e.g. decorative material) on the LED light. There is a risk of fire!
- The light source of this light is not replaceable; when the light source has reached the end of its life, you need to replace the entire light.
- The LED module is not dimmable.
- This product is not suitable for room lighting and is therefore not subject to EU Directive 2019/2015. As a result, the article also does not have an energy label. The LED module is not replaceable.
4. Product characteristics
- The plant lamp supports plant growth when daylight is scarce, over winter or during germination. It can be used on pot plants, succulents, ornamental plants, fruit and vegetables.
- Make sure that the distance between the LED module and the plant is at least 5 cm.
- Plants should be cut back, harvested or regrouped if they grow too close to the light source.
- The plant centre provides the necessary lighting as a component for healthy plant growth. In order to maintain the health of the plants, other components such as humidity, temperature and nutrients are essential.
- Depending on the plant type, the recommended Lux value (distance between the lamp and plant) and the illumination period in hours may differ. Inform yourself about your plants sufficiently to avoid loss of plants.
- The product is designed for indoor use. The plant light is operated via mains voltage.
- The use of the light should only be carried out as described in these instructions. Any other use is considered improper and may result in damage to property or personal injury.
- The plant light is intended exclusively for private use and is not suitable for commercial use. The item is not a toy and must always be kept out of the reach of children.
5. Installation
Insert the two upper connecting bars (A) on one of the side panels and then connect the remaining side panel to the other end.
6. Operation
Warning
- Only operate the product from an approved socket that is connected to the public power supply. The socket must be installed close to the product and must be easily accessible.
- Disconnect the product from the power supply using the On/Off switch if this is not available, unplug the power cord from the socket.
- If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the socket strip’s maximum throughput rating.
- If you will not be using the product for a prolonged period, disconnect it from mains power.
- Connect the power cable to a properly installed and easily accessible mains socket.
- The LED module can be switched on via the cord switch.
- The electronic control simulates a day/night cycle: the LED automatically stays on for 16 hours and then off for 8 hours. Due to the wide light beam, the entire interior area is evenly illuminated. If the plants require a different day/night cycle, the light control can also be simulated via an additional timer.
- If, for example, your plant only needs 10 hours of daylight instead of 16, the on and off times (day/night cycle) can be programmed with the help of an external timer.
7. Care and maintenance
Note Disconnect the device from the mains before cleaning and during prolonged periods of non-use.
- Only clean this product using a lint-free, slightly damp cloth and do not use any harsh cleaners.
- Ensure that no water is able to enter the product.
8. Warranty disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or from failure to observe the operating instructions and / or safety notes.
9. Technical data
PPF: Photosynthetic active photon flux measures the amount of photons within the PAR spectrum (400-700nm) per second. Only light in this spectral range is essential for photosynthesis. The measured value indicates the efficiency of a plant lamp, not the amount of photons.
· PPFD: the photosynthetic photon flux density indicates the amount of photons arriving on the surface of the plants (per second). This depends on the distance to the light source.
Distributed by
Hama GmbH & Co KG
86652 Monheim/Germany
Service & Support
www.xavax.eu
+49 9091 502-0
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.