MICTUNING MIC-LRL-550 C3 Extensible LED Rock Lights Wireless Control Instruction Manual

October 30, 2023
MICTUNING

MICTUNING MIC-LRL-550 C3 Extensible LED Rock Lights Wireless Control

MICTUNING-MIC-LRL-550-C3-Extensible-LED-Rock-Lights-Wireless-Control-
PRODUCT

Before You Read Thanks for purchasing our C3 RGBW LED Rock Lights Please read the instruction completely and make sure you have full understanding of this product before use

Accessory

MICTUNING-MIC-LRL-550-C3-Extensible-LED-Rock-Lights-Wireless-Control-
FIG-1

C3 Installation Steps

C3 Wiring Diagram

Installation Diagram

MICTUNING-MIC-LRL-550-C3-Extensible-LED-Rock-Lights-Wireless-Control-
FIG-4

Technology Parameter

The Pairing Way For Added Rock Lights:

  1. Turn on the wire harness switch three times repeatedly (each interval shall not exceed 5 seconds), wait for the LED light to flash to enter the pairing mode.
  2. Long press the Breathing Button of control box for five seconds to connect. When the indicator light is steady on, the pairing is successful.
    Note : The above operations are suitable for adding new rock lights

APP Introduction

The MICTUNING APP supports BLE and SPP Bluetooth protocols By connecting Bluetooth, you can easily control and customize mictuning’s Smart LED Lighting products. Feature with RGBW multi-colors, create amazing atmosphere. Perfect for automotive and other uses.

MICTUNING APP with multiple lighting modes including single color, jump, fade, music mode and more. DIY the color to fit for special occasions like off-road racing, car party and so on.

Guide Page

MICTUNING-MIC-LRL-550-C3-Extensible-LED-Rock-Lights-Wireless-Control-
FIG-8

Home Page

MICTUNING-MIC-LRL-550-C3-Extensible-LED-Rock-Lights-Wireless-Control-
FIG-9

Music Page

DIY Page

MICTUNING-MIC-LRL-550-C3-Extensible-LED-Rock-Lights-Wireless-Control-
FIG-11

Settings Page

Modify Name Page

Group Page

Detection Page
Check whether the RGBW color works normally. The interval between the light on & off is 1s, and it will continue to cycle without exiting the self-detection interface. PIs note that whether the light color is consistent with the color indicated by the APP when detect.

Single Set Control

Multi Sets Control

Bluetooth Connection Failure

  1. Check whether it is normally powered on
  2. Use the control box to check whether the indicator works properly
  3. The APP must be authorized, otherwise it cannot be connected
  4. Android phones require Bluetooth pairing when it connected to the device for the first time in APP

Customer Questions & Answers

What is the maximum distance between the lights and the control box to maintain a normal connection?
The control box controls the LED rock lights by radio. Since the radio signals are easily shielded by metal and earth, the communication distance changes accordingly. In an open environment, the maximum communication distance is 10-20m. For installation in a complex environment, it is recommended to place the light to the installation position firstly, then power on, and conduct a communication test through the control box to ensure that the control box can control the lights, finally install the lights.

Why the lights are still off after power off and power on again?
The lights will undergo power-off protection when off, to avoid accidental damage to the internal precision components. After power on, it will conduct a self-check and enter the silent state. At this time, the lights are still off and need to be controlled by sending a signal through the control box.

Can Mictuning APP control multiple sets of C3 products at the same time?
Can not control at the same time, can only switch to control one set. If you want to control more than 8 pods light, you can do it through pairing.

Scan the OR code to download APP

Thank you very much for purchasing MICTUNING product MICTUNING® All Rights Reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals