LOOK 69455.XXXX.YYK.RMT Backlit Mirror Instruction Manual
- June 13, 2024
- LOOK
Table of Contents
LOOK 69455.XXXX.YYK.RMT Backlit Mirror
Product Information
- The Look Backlit Mirror is a stylish and functional mirror that features a backlit design. It is available in different styles and variations, with part number 69455.ELS.XXXX.YYK.RMT &.EU, 69455.XXXX.YYK.RMT &.EU, 694XXWWHH-KKLL00M, and 694SHWWHH-KKWW004.
- The mirror comes with all the necessary installation parts and tools, including the power supply, mounting hardware (purchased separately), tape measure, and electric drill.
- It is important to read and follow all the instructions provided in this manual before using the mirror. Installing the mirror incorrectly may void the warranty and pose risks of burns, fire, electric shock, or injury to persons.
Product Usage Instructions
- Before installation, mark the location of the mounting holes according to the individual product specifications. Ensure that the bottom edge of the reflecting surface is no higher than 40 inches (1015mm) above the finished floor. For lit mirrors, measure to the innermost edge of the lit portion.
- Using the provided #14 round slotted wood mounting screws, install them into the pre-marked holes. Note that all mirrors must be installed in contractor-supplied blocking.
- Slide the mirror assembly onto the screws and ensure that each screw sits securely at the top of the keyhole slot.
Troubleshooting:
If you encounter any issues with the mirror, follow these troubleshooting steps:
- If the mirror doesn’t light up, check the connection between the mirror and the building’s wiring. Also, verify that there is power coming out of the power supply and 120V power coming out of the building’s junction box. Additionally, ensure that the tape light has not been unplugged from the power supply.
- If only part of the mirror won’t light up, it may be due to a bad LED. However, before assuming this, follow the previous steps to ensure all connections are done correctly.
Note: The above mirror image is for reference only. Refer to the dimensional drawings provided for each individual mirror for specific details on size, power supply placement, keyhole slots, and more.
PARTS/TOOLS NEEDED
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
- Read all instructions before using this mirror.
- MIRRORS SHOULD ONLY BE INSTALLED USING THE FOLLOWING INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID THE WARRANTY.
- WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
- Unplug the power before putting on or taking off parts.
- Close supervision is necessary when this mirror is used by, or near children, invalids, or disabled persons.
- Use this mirror only for its intended use as described in these instructions. Do not use attachments not recommended by ITC Architectural
- Never operate this mirror if it has a damaged cord, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact ITC Architectural for a replacement mirror.
- Keep the cord away from heated surfaces.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Exposing the mirror edges to liquids may cause permanent discoloration to the mirror etching which is NOT covered by the ITC warranty.
- WARNING: Risk of electric shock – Connect this mirror to a properly grounded outlet only. See grounding instructions.
CLEANING INSTRUCTIONS
- Clean mirrors with warm water and a soft, lint-free cloth, do not allow liquids to seep under the edges. Don’t use abrasive, acid, or alkali cleaners or products with ammonia or vinegar.
- Apply mild cleaners directly to a cloth, do not spray directly on the mirror. Applying liquids directly to the mirror’s surface may allow the liquid to seep/wick between the layers on the edge of the mirror.
- If this occurs there may be a permanent discoloration on the mirror etching which is NOT covered by ITC warranty.
- Dry the mirror immediately following cleaning and make sure all joints and edges are dry.
- Mark the location of the mounting holes. See individual product specifications for mounting hole locations.
- ADA requires that “Mirrors shall be mounted with the bottom edge of the reflecting surface no higher than 40 in (1015mm) above the finished floor1.”
- For lit mirrors, this means the dimension is to the innermost edge of the lit portion.
- Install included #14 round slotted wood mounting screws into pre-marked holes. Note, that all mirrors must be installed in contractor-supplied blocking.
- Slide the mirror assembly onto the screws.
- Slide the mirror assembly onto the screws.
TROUBLESHOOTING
The mirror doesn’t light:
- A. Check the connection between the mirror and building’s wiring.
- B. Verify that there is power coming out of the power supply.
- C. Verify that there is 120V power coming out of the building’s junction box.
- D. Verify that the tape light has not been unplugged from the power supply.
Part of the mirror won’t light:
- E. This is mostly likely due to a bad LED, however, follow the previous steps to make sure all connections are done correctly.
- Note: The above mirror image is to be used for reference only, see dimensional drawings for each individual mirror for details on size, power supply placement, keyhole slots, etc.
- 3030 Corporate Grove Dr. Hudsonville, MI 49426 Phone: 616.396.1355 itc-us.com
- For warranty information please visit www.itc-us.com/warranty-return-policy DOC #: 710-00009 Rev M 06/14/23
- 2010 ADA Standards 603.3 https://www.ada.gov
Documents / Resources
| LOOK
69455.XXXX.YYK.RMT Backlit
Mirror
[pdf] Instruction Manual
69455.XXXX.YYK.RMT Backlit Mirror, 69455.XXXX.YYK.RMT, Backlit Mirror, Mirror
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>