DEERC YUNGCHOI1988 Remote Control Car Instruction Manual

DEERC YUNGCHOI1988 Remote Control Car

Preface

WARNING: PLEASE READ THE INSTRUCTION MANUAL CLEARLY BEFORE OPERATING THE PRODUCT

To make your experience with this remote control car as easy and convenient as possible, please read me instructions provided before using my product. enjoy and have fun with the product while Keeping the manual or future maintenance and reference.

1. In order to protect the legitimate rights and interests of users, please be sure to carefully read the contents of this manual before using this product.
2. When using this product, please be sure to strictly observe and perform the requirements which includes but not limited to the instructions and safety guidelines. For any personal injury, accident, property loss, legal dispute, or any other adverse event causing a conflict of interest resulting from the use of the product or any irresistible factors that are in violation of the safety instructions, the user shall bear the related responsibilities and losses. DEERC will not take any responsibility.
3. Once you start using the product, you are deemed to have read, understood, recommended, and accepted all terms and contents of the instructions (including disclaimers, safety instructions, warning instructions, etc.) included with this product.
4. In case you are having challenges on any aspect of the product, may it be operation or maintenance, please contact your local sales agent or contact customer support at DEERC.

Contents

Charging

The battery isn’t fully charged when you first get it. When the car battery low, the car will start the LVC (Low Voltage Cutoff) protection function to protect the battery, the car can only turn, not forward and backward. Please charge the battery.

1. Plug the USB charging cable into the USB charging port of the computer, power bank or US adapter (5V@ 0.5-2.0A).
2. Connect the battery wire to the USB charging cable.
3. Charging time: about 120 minutes.
4. The green indicator light on the USB charging cable will flash when it is charging and will turn sol once fully charged.

ATTENTION:

• Cool the battery for 10 to 15 minutes before charging.
• Please keep the battery in sight when charging. DO NOT put the battery on a flammable surface.
• If battery pack and USB charging cable are damaged, immediately stop using it and replace the accessories as soon as possible.

Vehicle And Transmitter Parts

Battery Installation

RC Car Battery

1. Put the battery into the battery compartment and hold it in place with velcro.
2. Connect the battery outlet to the cable in the battery compartment If the car will not be used for a long time. make sure to turn it off and remove the battery.

Remote Battery:

1. Push the battery cover out.
2. Insert 2 AA batteries ( not included) in the correct direction.
3. Push the battery cover in.

If the remote will not be used for a long time, make sure to turn it off and remove the batteries. When the battery of the remote control is low, the indicator light of the remote control will flash slowly.

Battery Installation

1. Make sure the battery is charged.
2. Insert batteries to the car and the remote.
3. Turn on the remote power switch, then press and hold the car power switch to turn on the car. (DO NOT pull the throttle trigger during pairing)
4. Both will automatically pair. (The remote power indicator and the car power indicator will flash while waiting for the pairing process and will turn solid once pairing has been successful)

Forward/Reverse/Turn Left/ Turn Right

Pull the throttle trigger backward, the car goes forward. Push the throttle trigger forward, the car brakes, then push the throttle trigger forward again, the car goes reverse. (The throttle controls the speed )
Turn the steering control wheel counterclockwise, the car turns left. Turn the steering control wheel clockwise, the car turns right. (Control the Steering Wheel Rotation Angle can control the degree of turing).

Maximum Speed Control

Steering Trim

If while the car is moving forward and veering to left then turn the steering trim konb to the right until the car is moving straight. If while the car is moving forward and veering to right then turn the steering trim konb to the left until the car is moving straight.

Specifications

Frequent Asked Questions

Assembly Exploded Diagram

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following so conditions: This device may not cause harmful interference, and This device must accept any interference received. including interference that may cause undesired.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency eneray and. if not installed and used in accordance with the instructions, may cause harm interference to radio communications. However, there is no guarantee that interference will no occur in a particular installation. If this equipment does cause harm interference to radio or television reception. which can be determined by turning the equipment of and on, the user is encouragod to try to correct the interference by one or more of the following *content or relocate the receiving antenna Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected consult the dealer or an experienced radio y technician for help.
cause harm interference Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC Notice

This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference. Including interference that may cause undesired operation of the device.

BATTERY WARNING:

1. Failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion.
2. Always check the battery’s condition before charging or using it.
3. Replace the battery if it has been dropped, or in case of odor, or overheating. discolouration, deformation or leakage.
4. Never use anything other than the approval charger the battery. Always use a balancing charger for battery. It is recommended that you do not to use any other charger than the one provided with the product.
5. The battery temperature must never exceed 60°C (140’F) otherwise the battery could be damaged or ignited.
6. Never charger on a flammable surface, near flammable products or inside a vehicle (preferably place the battery in a non-flammable and nonconductive container).
7. Never leave the battery unattended during the charging process. Never disassemble or modify the housing’s wiring, or puncture the cells. Always ensure that the charger output voltage corresponds to the voltage of the battery. Do not short circuit the batteries.
8. Never expose the battery to moisture or direct sunlight, or store it in a place where temperatures could exceed 60°C(car in the sun, for example).
9. Always keep it out of reach of children.
10. Improper battery use may result in a fire, explosion or other hazard.
11. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are only to be charged under adult supervision.
12. Different types of batteries or new and used batteries are not to be mixed.
13. Batteries are to be inserted with the correct polarity.
14. The supply terminals are not to be short-circuited. Regular examination of transformer or battery charger for any damage to their cord, plug, enclosure and other parts and they must not be used until the damage has been repaired.
15. The packaging has to be kept since it contains important information.
16. The toy is only to be connected to Class Il equipment bearing the symbol.

MANUFACTURER INFORMATION Manufactured by SHANTOU PENGXIANG TOYS FACTORY Pengxiang Building.Gangxia Road.Bumei Industrial Zone,Chenghai Area,Shantou 1 City Guano Don Province CHINA Please do not hesitate to contact us if you need further
supportusa@edeerc.com (America)
eu@deerc.com (Europe)
prodeerc.com Japan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>