DEERC D10 Foldable Drone with Camera for Adults Instruction Manual

: June 15, 2024
: DEERC

DEERC D10 Foldable Drone with Camera for Adults Instruction Manual

DISCLAIMER & WARNING

Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product. This product is not recommended for people under the age of 14. By using this product you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damages caused while using this product, and its consequences You agree to only use this product for it’s designed purposes and in accordance with local laws, regulations and all applicable policies and guidelines that Deerc may provide
When using this product, please be sure to strictly abide by the specifica tion requirements and safety guidelines stated in this document. Any personal injury, property damage legal disputes and all other adverse events caused by the violation of any of the safety instructions or due to any other factor, WILL NOT be Deerc’s responsibility

SAFETY GUIDELINES

Check Before Use

This product is a high precision drone that integrates various electronic stability and control mechanisms. Please be sure to configure this drone carefully and correctly to ensure safe, accident-free operation
Ensure that the batteries of the drone and transmitter are clean, undam aged and fully charged before every use
Ensure that all the propellers are undamaged and are installed in the correct orientation.
Ensure that all the propellers are undamaged and are installed in the correct orientation.
@ Ensure to do a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear of the propeller, battery power and effectiveness of the indicator, etc. If after doing a complete check of the drone any problems are found, please refain from using it until the problem has been resolved

Flight Environment

Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airports or bodies of water. DO NOT fly near strong electromagnetic sources such as power lines and base stations as it may affect the onboard compass.

DO NOT use this drone in adverse weather conditions such as rain, snow, fog, and wind.
Flight Environment

Operation Requirements

DO NOT use this product to follow ary moving vehicles.
During the fiight. turn off the motors only in case of an emergency.
Fly the drone back to you as soon as you are notified that the battery is running low,
This product should not be used while drinking alcohol or consuming drugs, if you are feeling fatigued, taking medicine, or feeling any physical discomfort
Be aware of the volume of noise that the drone produces. Please ensure to keep your distance to avoid ear damage.
stay away from the rotating propellers and motors.
DO NOT fly in any spaces where drones are prohibited. Please respect people’s right to privacy by not flying your drone close to others.

Use of Battery

Please ensure batteries are fitted in the correct orientation as shown in the instruction manual.
Avoid short circuits by fitting the batteries correctly, and do not crush or squeeze the batteries as this could cause the risk of a fire or explosion.
DO NOT mix new and old batteries as this can lead to a poor perfor- mance of the product
Please dispose of used batteries carefully, do not litter and recycle where ever possible
DO NOT expose dead batteries to heat o fire or they may explode
If the device is not going to be used for an extended period of time, please remove batteries to prevent potential damage from to the drone battery leakage.
Only use the USB charging cable that comes with the drone to charge the battery.
DO NOT connect the battery directly to wall outlets or car cigarette lighter sockets as this will damage your battery as they are a different voltage.
DO NOT attempt to disassemble or modiify the battery in any way
DO NOT use the battery if it gives off an odor, generates heat, becomes discolored, deformed or appears abnormal in any way. If any of these situations occur while the battery is in use or being charged, remove it from the device or charger immediately and discontinue use.
DO NOT pierce the battery casing with a nail or any other sharp object, break it open with a hammer, or step on ifl Dispose or recycle this battery as it may cause personal injury or damage to your drone.
Aways charge the batteries on a fireproof surface and away from combustible materials. DO NOT charge on surfaces that can catch fire. This includes: wood, cloth, carpet, or on the application’s device.
DO NOT immerse the battery in water or get it wet.
DO NOT solder battery terminal in any way.
Keep batteries out of reach of children or pets
DO NOT short-circuit the battery by connecting wires or any other metal object to the positive|+) and negative[-| terminals.

Li-Po Battery Disposal & Recycling
Waste Limsum polymer batteries must not be placed with household rush Proine contact local environment or waar agering of the waste agency or the suppiler of your model or your nearest LiPo battery recycling conter

MAINTENANCE

Clean the product after each se with a clean, soft cloth,
Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone or batteries.
This device is not waterproof and must not be submerged or subjected in water under any circumstance. Failure to keep the device completely dry will result in the failure and permanent damage to the unit. Be aware that although it might be dry where you are, droplets of rain or mist from a river or waterfall could be damaging your drone where itis fiing
Frequently Check the charging plug and other accessories for sigrs of damage. If any part of the device or cables are damaged, avoid use or charging unti the device can be serviced.

PACKAGE CONTENTS

| |
---|---|---
Drone| Transmitter| Drone Battery
| |
USB Charging Cable| Propeller Guard| Propeller
| |
Screwdriver| Instructions For Use|

DRONE DETAILS

TRANSMITTER DETAILS

JOYSTICK MODE

MODE 2: (L&ft hand throttle MODE 2 will be default setting.)
Left Joystick

Right Joystick

MODE 1
To enter MODE 1, turn on the transmitter while holding the “Speed Switch” button. (Please do not release the “Speed Switch” button until the transmitter is powered on.] **Left Joystick

Right Joystick

**

CHARGING

When the drone battery runs low, the indicator lights on the drone will flash continuously.
Remove the battery and connect the USB charging cable to the battery.
Plug the USB charging cable into a USB charging port on power bark or USB adapter (5V/2.0A ) 4]
The red indicator light on the battery will turn on when the battery is charging, and will tun green when the battery is fully charged
Charging time: about 90 minutes A Before charging, please check the contents of the

Use of Battery” section of the “ Safety Guidelines” carefully!

INSTALLATION

Propellers

The drone will not fly unless the correct propeller is installed on the correct motor shaft. See illustration above. An “A” or “B” is printed on the each propeller. Lock the propeller to the motor shaft with screw rotating each screw clockwise.

Drone Battery

Installation: Push the battery into the battery compartment at the rear of the drone. Make sure the battery is in place to ensure that the battery is Jjammed in the battery compartment. **(Pic.1)

Removal: Press and hold the lock on the battery at the same time while pulling backwards to remove the battery. (Pic.2)

Propeller Guard

Installation Instruction Installation : Line up the protruding points on the propeller guard with the sunken grooves on the drone and insert them together. Tightly press both sides of the propeller guard into place after the sunken grooves and protruding points have completely interlocked.
Removal: Lightly pull on the clip on one of the ends of the propeller guard outwards until it has separated from the inside of the drone, at which point the propeller guard can be fully removed.

Transmitter Battery

Installation Instruction

As shown above, insert the battery into the battery compartment. Please pay attention to the positive and negative polarity of the battery to ensure the correct installation of the battery.

Phone Holder

Installation Instruction
As shown above, pull the phone holder down and insert the phone.

OPERATION GUIDE

Download APP
ios

Android APP on Google play

Scan the QR code, corresponding to either App Store ™ or Google Play™ Store and download the Deerc FPV app for free. Required Operating Systems: IOS 12.0 or later/Android 4.4 or later.

Pairing

Press and hold the power button o wn on the done and the indicator lights on the drone begins to flash.
Place the drone on a flat and level surface with the head forward and the tail towards the pilot.
Press the power button on the transmitter to turn it on and you will hear “Di D¥”, then the indicator light on the transmitter will flash.
Push the left joystick up then down to pair the drone with the transmitter. The indicator lights on the drone and the transmitter will turn solid if the drone is paired successfully.

Calibrating the Gyroscope

Push the left and right joystick simultaneously to the lower left corner to calibrate the gyro. When the indicator lights on the drone change from flashing quickly to solid, it indicates that the calibration has been completed.

Tips: To ensure a stable flight, we suggest that the pilot calibrates the gyro every time after pairing the drone and after a crash.

One Key Takeoff/Landing

Short press the One Key Takeoff/Landing button, the drone will automatically take off and hover at 5 feet altitude.
When the drone is flying, short press the same button again, the drone will automatically land on the ground.

UNCTION DETAILS

**Emergency Stop

The Emergency Stop function can be only used in case of emergen- ¢y during the fiight to avoid any of damage or injury.**

Press and hold the Emergency Stop button for about 2 seconds, the motors will stop immediate 1y.

**Speed Switch

** This d {Low/Medium/High). Press the Speed Switch bui mitter to switch the speed e comes with 3 speed
Di” indicates Low Speed, “Di DI” indicates Medium Speed and “Di Di Di” indicates High Speed [The Low Speed is default speed mode.

Trimmer Function Installation Instruction F/B Sideways Drift Trim: If the drone tends to drift forward, hold down the “Speed Switch” button and do not release it while pushing the direction joystick down to re-balance the drone. If the drone tends to drift backwards, hold down the Speed Switch” button and do not release it while pushing the direction joystick up to re- balance the drone.
Installation Instruction

L/R Sideways Dip Trim: If the drone tends to drift left, hold down the “Speed Switch” button and do not release it while pushing the direction joystick right to re-balance the drone. If the drone tends to drift right, hold down the “Speed Switch” button and do not release it while pushing the direction joystick left to re-balance the drone.

Take Photo/Video Installation Instruction
Take Photo: Short press the Photo button on the transmitter to take pictures. One beep can be heard from the transmitter, indicating the camera has successfully taken one photo.
Record Video: Short press the Video button on the transmitter, two beeps

from the transmitter will be heard. This tells you that the camera has started recording video. You can exit the recording by pressing the same button again.
Do not take photos during the recording, which will interrupt the recording.

Altitude-Hold Function

The drone is designed with altitude-hold function so the drone can maintain its altitude after you release the left joystick the left joystick will automatically spring back to the middle ).

360° Flip

Installation Instruction When you get familiar with all the functions of the drone, you can try this amazing flip mode. When you fly the drone at least 10 feet, press the 360° Flip button on the transmitter, then push the right joystick Forward/ Backward or Left/Right, and the drone will do a flip towards the corresponding direction.
If you are in MODE 1. push the right joystick Left/Right or push the left joystick Forward/Backward, and the drone will do a flip towards the corresponding direction.
4 This function will perform better when the battery is fully charged.

Circle Fly

Installation Instruction Press and hold the Photo button for about 3 seconds, the drone will enter the Circle Fly mode. Exit the Circle Fly mode by long pressing the same button again or pushing the direction joystick.

Auto-Rotation

Press and hold the Video button for about 3 seconds, the drone will enter the Auto- Rotation mode. Exit the Auto-Rotation mode by long pressing the same button again or pushing the direction joystick.

Headless Mode

After pairing/calibration, or during the flight of the drone, short press the Headless Mode button to enter Headless Mode. In Headless Mode, the indicator lights of the drone will flash continuously, and the transmitter will send out alarm sound continuously.
Short press the Headless Mode button again, and you will hear one beep, which indicates the drone exits the Headless Mode

Installation Instruction
lease make sure the pilot stays in the same orientation as the drone head faces when the drone is takeoff.

Under Headless Mode, the forward direction is the direction that the head of drane faces when the drone is take-off. In order to make sure the pilot
can tell drone’s direction, we recommend that pilots to stay in the same orientation as the drone’s head faces when the drone takeoff. When the pilot pushes the direction joystick forward, the drone wil fly forward, If the pilot pushes the direction joystick backward, the drone will fly towards
him/her. If the pilot moves the right stick left/right, the drone will move lefyfight refative to you

SPECIFICATIONS

DRONE
Model: D10
Weight: 164g/5.7802
Max Flight Time : 12 minutes {per battery)
Operating Temperature Range: 32″ to 104°F [0 ta 40°C)
Size: 340%340%65 mm [Unfolded) 18014265mm [Folded)

DRONE BATTERY
Capacity: 1000mAh
Voltage: 3.7V
Energy: 3.70 Wh
Battery Type: Lithium-ion Polymer Battery
Charging Temperature Range: 41° to 104°F (5″ to 40°C)
Charging Time: 90 minutes [depends on charging power and remaining battery power)

TRANSMITTER

Operating Frequency: 2452-2474MHz
Max Flight Distance: 328 feet/ 100m (outdoors and unobstructed)
Operating Temperature Range: 32″ to 104°F (0 t0 40°C)
Battery Type: 1.5 AA Battery (not included)

CAMERA
Operating Frequency: 5500-5700MHz
Photo Resolution: HD2048x | 152P
Transmission Distance Range: 196~262feet/60~80m [outdoors and unobstructed)
Transmission Frame Rate: 25 fps
Photo Formats: JPEG
Video Formats: AVI/MP4 Operating Temperature Range: 32° to 104°F {0 to 40°C)

USB CHARGING CABLE
Input: 5V/2 A Rated
Power. ≤10W

13.0 CONTACT US
Please do not hesitate to contact us if you need further support.
4:00 PM 7:00 AM (PST)
usa@deerc.com (USA)
jp@deerc.com (JP)
eu@deerc.com (EU)
+1(855)777-8866

For online support, please scan this code with Live Chat

GENERAL INFORMATION
FCC Notice
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions

This device may not cause harmful interference
This device must accept any interference received, including interfer ence that may cause undesired operation
The Supplier’s Declaration of Conformity is available at the following address
https://www.deerc.com/Download/US/D10_FCC_sDoCpdf

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are set to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and ran radiate radio frequency energy, if not installed and used in accordance with the instruc- tions, it may cause harmful interference to radio communications. Howev er, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can not be determined by turning the equipment off and on, the user is encouraged to try one or more of the following measures

Reorient or relocate the receiving antenna
Separation more distance between the equipment and receiver
Connect the equipment to an outlet on a circuit different from the receiver.
onsult the dealer or an experienced radio/TV technician for help.

WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
RF Exposure
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.

IC Notice
This device is restricted to indoor use when operating in the 5150 to 5250
MHz frequency range
This device complies with Canada Industry licence-exempt RSS standard(s)
Operation is subject to the following two conditions

this device may not cause interference; and
this device must accept any interference Including interference that may cause undesired operation of the device

HOW TO RECYCLE THIS PRODUCT

This symbol on the product or its documentation indicates that it MUST not be disposed of together with household waste

Uncontrolled waste disposal may harm the environment or human health. Please separate your device from other types of waste for recycling it responsibly.

This will help to foster the sustainable re-use of material resources We suggest you contact your retailer, inquire at your local town hall or business store to find out where and how the drone can be recycled.

BATTERY WARNING

Failure to follow all the instructions may result in serious injury, irreparable damage to the battery may cause a fire, smoke or explosion as well
Always check the battery’s condition before charging or using it
Please replace the battery if the battery is dropped or has any peculiar smell, overheating, discolouration, deformation o leakage happens
Never use anything other than the approved LiPo charger to charge the battery. Always Use a balancing charger for LiPo cells or a LiPo cell balancer. Itis recommended that you use the one provided with the product
The battery temperature must never exceed 60°C(140F) otherwise the battery could be damaged o ignited.
Never charge the battery on a flammable surface, near flammable products or inside a vehicle{preferably place the battery on a non-flammable and non conductive surface].
Never leave the battery Unattended during the charging process. Never disassernble or modify the housing’s wiring, or puncture the cells. Always ensure that the charger output voltage corresponds to the voltage of the battery. DO NOT short circuit the batteries.
Never expose the L-Po battery to moisture or direct sunlight, or store it in
place where temperatures could exceed 60°Clcar in the sun, for example)
Always keep it out of reach of children
Improper battery use may result in a fire, explosion or other hazards
Non-rechargeable batteries are not allowed to be recharged. Rechargeable batteries should be charged under adults’ supervision,
DO NOT mix different types of batteries including the new and used ones.
13, Batteries MUST be inserted with the correct polary.
The supply terminals MUST not to be short-circuited. Regular examination of transformer or battery charger for any damage to their cords, plugs, enclosures and other parts MUST be done. If there is damage, they MUST not be used until the damage has been repaired.
Thee packaging has to be kept since it contains important information.
This toy is only can be connected to the equipment with symbol Class I

Caution

The max operating of the EUT is 45°C. and shouldn’t be lower than -10°C.
The device complies with RF specifications when the device used at Omm form your body.
eclaration of Conformity.

We, Xiamen Huoshiquan Import & Export CO,LTD
hereby, declare that the compliance of the essential requirements with the
Directive 2014/53/EU, the RoHS Directive 2011/65/EU and Safety
Directive 2009/48/EC have been fully fulfiled on our product with
indication below:
Product Name: Remote control four axis series
Model/Mark: D10/DEERC
The Statement of compliance is available at the following address:
hitpy//wwww.deerc.com/Download/CE/D10_EU_DOC pdf

This product can be used among EU member states

MANUFACTURER INFORMATION
Manufactured by
Xiamen Huoshiquan Import & Export CO,LTD,
Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming
District, Xiamen, China
+1(855/777-8866