DEERC D11 Drone for Kids Instruction Manual
- June 14, 2024
- DEERC
Table of Contents
D11 Drone for Kids
Product Information
-
Product Name: D11 Drone
-
Version: V 1.0
-
Contact Information:
- USA: usa@deerc.com, +1(855)777-8866
- EU: eu@deerc.com
-
Package Contents:
- Drone
- Transmitter
- Drone Battery
- USB Charging Cable
- Propeller
- Propeller Spanner
- Screwdriver
-
Diagram of Drone:
- Propeller A
- Propeller B
- Propeller B
- Power Switch
- Propeller A
- Drone Indicator
- Drone Battery
- Front LED
-
Diagram of Transmitter:
- Left Joystick
- Right Joystick
- Power Switch/Indicator
- Forward Trimmer
- Left Trimmer
- Backward Trimmer
- Right Trimmer
- Speed Switch
-
Joystick Modes:
-
MODE 2 (Left hand throttle MODE 2 will be the default
setting.) -
MODE 1
-
Product Usage Instructions
Safety Guidelines
Before using the drone, please read and follow the safety
guidelines:
-
Fly in open areas.
-
Maintain line of sight.
-
Fly below 131 ft (40 m).
-
Avoid flying over or near obstacles, crowds, high voltage power
lines, trees, airports, or bodies of water. Do not fly near strong
electromagnetic sources as it may affect the onboard compass. -
Do not use the drone in adverse weather conditions such as
rain, snow, fog, and wind. -
Stay away from the rotating propellers and motors.
Operation Requirements
To prevent potential damage to the drone from battery leakage,
please remove batteries when not in use.
Li-Po Battery Disposal & Recycling
Waste lithium-polymer batteries must not be placed with
household trash. To dispose of waste batteries, please contact the
local environmental or waste agencies, the supplier of your model,
or your nearest Li-Po battery recycling center.
Maintenance
No specific maintenance instructions provided in the manual.
Preparation Before Flight
Before flying the drone, follow these steps:
-
Charge the drone battery using the USB Charging Cable and a USB
adapter (5V/1A). -
When the battery is fully charged, the indicator light on the
USB Charging Cable will turn green. -
Low Battery Signal: The drone indicator will flash continuously
and the transmitter will beep during the flight. -
Before charging, read the instructions in the Use of Battery
section of the Safety Guidelines carefully. -
Use the original charging cable to charge the battery.
-
Do not charge the drone battery immediately after a flight as
the temperature of the battery may be too high. Wait until it cools
down to room temperature before charging again.
Instructions For Use
Gebrauchsanweisungen
V 1.0
D11
usa@deerc.com (USA) +1(855)777-8866
eu@deerc.com (EU)
English Deutsch
01-31 32-56 57-84
Contents
Disclaimer & Warning …………………………………………………………………….. 1 Safety Guidelines
…………………………………………………………………………….. 1 Maintenance
……………………………………………………………………………………. 5 Package Contents
……………………………………………………………………………. 6 Diagram Of Drone
………………………………………………………………………….. 7 Diagram Of
Transmitter………………………………………………………………….. 8 Joystick Mode
………………………………………………………………………………….. 9 Preparation Before Flight
Charging Drone Battery……………………………………………………………. 10 Changing Transmitter
Batteries……………………………………………….. 11 Drone Battery
……………………………………………………………………………..12 Propellers …………………………………………………………………………………….
13 Flight Pairing ………………………………………………………………………………………….14 Calibrate The Gyro
……………………………………………………………………. 15 Unlock The Motors …………………………………………………………………….
15 Takeoff …………………………………………………………………………………………16 Landing
………………………………………………………………………………………. 17 Functions Details Speed Switch
……………………………………………………………………………… 18 High-Speed Rotation
………………………………………………………………….18 Circle Fly ………………………………………………………………………………………19
360° Flip ……………………………………………………………………………………… 19 Emergency Stop
………………………………………………………………………… 20 Headless Mode …………………………………………………………………………..
21 Altitude-Hold Function ……………………………………………………………. 22 Attitude Adjustment
Trimmer ……………………………………………………………………………………….23 Specification
…………………………………………………………………………………….. 24 Contact Us
……………………………………………………………………………………….. 25 General Information
……………………………………………………………………….. 26
DISCLAIMER & WARNING
1. Please read this Disclaimer & Warning and Safety Guidelines carefully
before using our product. This product is not recommended for people under the
age of 14. By using this product, you hereby agree to this disclaimer and
signify that you have read it fully. You agree that you are responsible for
your own conduct and any damage caused while using this product, and any
consequence. You agree to only use this product for it’s designed purposes and
in accordance with the local laws, regulations and all applicable policies and
guidelines that DEERC may provide. 2. When using this product, please be sure
to strictly abide by the specification requirements and safety guidelines
stated in this document. Any personal injury, property damage, legal disputes
and all other adverse events caused by the violation of any of the safety
instructions or due to any other factor, WILL NOT be DEERC’s responsibility.
SAFETY GUIDELINES
CHECK BEFORE USE
æ This product is a high precision drone that integrates various electronic
stability and control mechanisms. Please be sure to configure this drone
carefully and correctly to ensure safe, accident-free operation ç Ensure that
the batteries of the drone and transmitter are clean, undamaged, and fully
charged before every use. èEnsure that all the propellers are undamaged and
are installed in the correct orientation.
-1-
SAFETY GUIDELINES
é Please perform a thorough check of the product before each use. Inspect the
integrity of the parts, any signs of cracks and wear off on the propellers,
battery power and effectiveness of the indicator, etc. If there is any problem
found after checking the drone, please refrain from using it until the problem
is resolved.
FLIGHT ENVIRONMENT
Fly in Open Areas
Maintain Line of Sight
Fly Below 131 ft (40 m)
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
Avoid flying over or near obstacles, crowds, high voltage power lines, trees,
airports or bodies of water. DO NOT fly near strong electromagnetic sources
such as power lines and base stations as it may affect the onboard compass.
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
DO NOT use this drone in adverse weather conditions such as rain, snow, fog,
and wind.
-2-
SAFETY GUIDELINES
OPERATION REQUIREMENTS
æ DO NOT use this product to follow any moving vehicles. ç During the flight,
turn off the motors only in case of an emergency. è When the battery runs low,
return the drone back to your starting point. é DO NOT use this product if you
feel tired, take medicine or feel unwell and drink alcohol. ê Be aware of the
volume of noise that the drone produces. Please ensure to keep your distance
to avoid ear damage.
Stay away from the rotating propellers and motors.
USE OF BATTERY
ìDO NOT fly in any spaces where drones are prohibited. Please respect people’s right to privacy by not flying your drone close to others.
æ Please ensure batteries are fitted in the correct orientation as shown in the instruction manual. ç Avoid short circuits by fitting the batteries correctly, and do not crush or squeeze the batteries as this could cause the risk of a fire or explosion. è DO NOT mix new and old batteries as this can lead to a poor
performance of the product. é Please dispose of used batteries carefully, do
not litter and recycle
where ever possible. ê DO NOT expose dead batteries to heat or fire or they
may explode. ë If the device is not going to be used for an extended period of
time,
please remove batteries to prevent potential damage to the drone from
battery leakage.
-3-
SAFETY GUIDELINES
ì Only use the USB charging cable that comes with the drone to charge the
battery. í DO NOT connect the battery directly to wall outlets or car
cigarette -lighter sockets as this will damage your battery since they have
different voltages. î DO NOT attempt to disassemble or modify the battery in
any way ï DO NOT use the battery if it gives off an odor, generates heat,
becomes discolored, deformed or appears abnormal in any way. If any of these
situations occur while the battery is in use or being charged, remove it from
the device or charger immediately and discontinue use. 11 DO NOT pierce the
battery casing with a nail or any other sharp object, break it open with a
hammer, or step on it! Dispose or recycle this battery as it may cause
personal injury or damage to your drone. 12 Always charge the batteries on a
fireproof surface and away from combustible materials. DO NOT charge on
surfaces that can catch fire, which includes: wood, cloth, and carpet. 13 DO
NOT immerse the battery in water or get it wet. 14 DO NOT solder the battery
terminal in any way. 15 Keep batteries out of reach of children or pets. 16 DO
NOT short-circuit the battery by connecting wires or any other metal object to
the positive(+) and negative(-) terminals.
Li-Po Battery Disposal & Recycling
Waste Lithium-polymer batteries must not be placed with household trash. To
dispose of waste batteries, please contact the local environmental or waste
agencies, the supplier of your model, or your nearest Li-Po battery recycling
center.
-4-
MAINTENANCE
æ Clean the drone after each use with a clean, soft cloth. ç Avoid prolonged
exposure to direct sunlight and avoid buildup of heat on the drone or
batteries. è This device is not waterproof and must not be submerged or
subjected to water under any circumstance. Failure to keep the device
completely dry may likely damage the unit permanently. Be aware that although
it might be dry where you are, droplets of rain or mist from a river or
waterfall could damage your drone where it is flying. é Frequently check the
charging plug and other accessories for signs of damage. If any part of the
device or cables are damaged, avoid using or charging until the damaged parts
are replaced.
-5-
PACKAGE CONTENTS
Drone
Transmitter
Drone Battery
USB Charging Cable
Propeller
Instructions For Use
Gebrauchsanweisungen V 1.0
D11
usa@deerc.com (USA) +1(855)777-8866
eu@deerc.com (EU)
Propeller Spanner
Instructions For Use
Screwdriver
-6-
DIAGRAM OF DRONE
1
2
4
3
5
6
1 Propeller A 2 Propeller B
3 Propeller B 4 Power Switch
5 Propeller A 6 Drone Indicator
7
8
7 Drone Battery
8 Front LED
· The front LED glows solid white to display the orientation of the drone. ·
The drone indicator displays the status of the flight control system.
-7-
DIAGRAM OF TRANSMITTER
1 3
2
5 4
1 Left Joystick 2 Right Joystick
3 Power Switch/Indicator 5 Takeoff/Landing
4 Forward Trimmer Left Trimmer
Backward Trimmer Right Trimmer
67
89
6 Speed Switch
7 Short press-High Speed Rotation Long press-Circle Fly
8 Headless Mode 9 360° Flip
-8-
JOYSTICK MODE
MODE 2 (Left hand throttle MODE 2 will be the default setting.)
Left Joystick
Right Joystick
Up
Ascend
Up
Forward
Down
Descend
Down
Backward
Left Right Rotate Left
Rotate Left Right
Right Fly to Left
Fly to Right
MODE 1
To enter MODE 1, turn on the transmitter while holding the ( ) button. (Please
do not release the ( ) button until the transmitter is powered on.)
Left Joystick
Up
Forward
Right Joystick
Up
Ascend
Down
Backward
Down
Descend
Left
Right
Rotate
Left
Rotate Left Right
Right Fly to Left
Fly to Right
-9-
PREPARATION BEFORE FLIGHT
CHARGING DRONE BATTERY
USB Adapter (5V/1A)
Power Bank æConnect the the drone’s battery with the USB Charging Cable. çPlug
the USB Charging Cable into a USB charging port on the power bank or USB
adapter (5V/1A). èCharging time: about 60 minutes. éa. When the battery is
charging, the indicator light on the USB Charging Cable is Red.
b. When the battery is fully charged, the indicator light on the USB Charging
Cable will turn Green. * Low Battery Signal: The drone indicator will flash
continuously and the transmitter will beep during the flight.
– Before charging, please read the instructions in the “Use of Battery”
section of the “Safety Guidelines” carefully! – Please use the original
charging cable to charge the battery. – DO NOT charge the drone battery
immediately after a flight as the temperature of the battery may be too high.
Please wait until it cools down to room temperature before charging again.
-10-
PREPARATION BEFORE FLIGHT
CHANGING TRANSMITTER BATTERIES
3*AAA Batteries (NOT included)
Battery Cover
Open the battery cover on the back of the transmitter, insert the three AAA
batteries (Not included) into the battery compartment, and close the battery
cover to complete the installation. – Please read the instructions in the “Use
of Battery” section of the “Safety Guidelines” carefully! – When installing
the batteries, please pay attention to the positive and negative polarity of
the battery to ensure the correct installation of the batteries.
-11-
PREPARATION BEFORE FLIGHT
DRONE BATTERY
1
2
Installation: As shown in the figure above, install the battery to the buckle
on the back of the drone and push it forward. Please make sure the battery is
securely installed.
2 1
Removal: As shown in the figure above, hold down the two sides of the battery
and pull it back, then remove the battery upwards.
-12-
PREPARATION BEFORE FLIGHT
PROPELLERS
A
HEAD
B
B
A
Installation: See illustration above, connect each propeller to its
corresponding motor shaft. Install the propeller to the motor shaft and press
into place.
– The propeller is installed before the drone is packaged at the factory. –
The drone will not fly unless the correct propeller is installed on the
correct motor shaft.
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
Removal: First turn the bottom of the drone up and unscrew the bottom screws.
Then insert the propeller spanner between the propeller and the motor. Be sure
to hold the motor while detaching the propeller.
-13-
FLIGHT
All of the following operations in this manual use MODE 2.
PAIRING
æ Long press the Power Switch Button to turn on the drone. The drone indicator
start flashing.
ç Place the drone on a flat and level surface, with its head facing forward and its tail pointing towards the pilot.
HEAD
è Long press the Power Switch to turn on the transmitter. Once the transmitter
sends out a long beep and the indicator changes from blinking to solid, the
drone will be paired with the transmitter.
-14-
FLIGHT
CALIBRATE THE GYRO
Push the left and right joysticks simultaneously to the outer, lower corners
to calibrate the gyro. The drone indicator will blink and turn solid, the
transmitter beeps one time, indicating that the calibration is completed.
To ensure a stable flight, we suggest that the pilot calibrates the gyro every
time after pairing the drone and after a crash.
UNLOCK THE MOTORS
Simultaneously push the left joystick to the bottom right corner and the right
joystick to the bottom left corner. The motors will rotate, and the drone is
unlocked.
Pull the left joystick down to the bottom for 2 seconds, and the motors will
stop spinning. The drone is thus locked.
-15-
FLIGHT
TAKEOFF
There are two methods to take off the drone. Method 1:
Short press the ( ) button again, the drone will automatically take off and
hover at 4 ft. At this time, you can control this drone by using the
joysticks. Method 2:
Takeoff Pick up the drone and lay it flat on your palm. Gently toss the drone
into the air, and it will hover in place.
-16-
LANDING
FLIGHT
When the drone is flying, short press the ( ) button, and the drone will
automatically land on the ground.
You must keep your drone in visual line of sight all the time. If you can’t
see it, you can’t control it.
-17-
FUNCTIONS DETAILS
SPEED SWITCH
short press
This drone comes with 3 speed modes (Low/Medium/High). Short
press the (
) button to switch between low, medium, and high
speed. The transmitter beeps once to indicate Low Speed, beeps twice
to indicate Medium Speed and beeps three times to indicate High
Speed. (The Low Speed is the default speed mode.)
HIGH SPEED ROTATION
short press
Short press the ( ) button, the transmitter will beep once, the drone begins to rotate quickly. Push the right joystick in any direction to stop the rotation.
-18-
FUNCTIONS DETAILS
CIRCLE FLY
long press
Long press the ( ) button, the transmitter will make a long beep, which
indicates that the drone has entered the Circle Fly function. Push the right
joystick in any direction to exit Circle Fly.
360° FLIP
10 ft
short press
When you get familiar with all the functions of the drone, you can try this
amazing flip mode. When the drone is at least 10ft from the ground. Short
press the ( ) button, then push the right joystick forward/backward or
leftward/rightward. The drone will do a flip toward the corresponding
direction.
360°Flip functions better when the battery is fully charged.
-19-
FUNCTIONS DETAILS
EMERGENCY STOP
The Emergency Stop function should only be used in case of emergency during
the flight to avoid any damage or injury.
æ Simultaneously long press the left and right joysticks, the motors will stop
immediately. Be aware that you risk breakage of the drone if it falls a large
distance or hits anything at a high rate of speed.
çAfter the drone hits the ground, The drone indicator will keep on flashing.
Please put the drone on a level surface again, and push the left joystick
downward. The drone indicator then turn from flashing to solid, which
indicates that you can use the drone now.
-20-
FUNCTIONS DETAILS
HEADLESS MODE
The Headless Mode is a great training tool for beginner pilots. It is also
useful when the drone is too far from the pilot (which makes it difficult to
tell its orientation). It keeps the drone traveling forward, backward, left,
or right when you move the right joystick in those directions, regardless of
which way the front of the head of the drone points to.
The pilot should stay facing the same direction that the drone’s head points
to when it takes off.
short press
Entering: Short press the ( ) on the transmitter. The drone Indicator keeps
flashing, indicating that the drone is in Headless Mode. Exiting: Short press
the ( ) on the transmitter again. It then beeps 1 time, indicating that the
drone has exited the Headless Mode.
-21-
FUNCTIONS DETAILS
- Why is the orientation of the drone important? In normal flying mode, the control of the drone movement can sometimes be counter-intuitive for beginners. For instance, when the drone is in the air with its head pointing to your right, if you push the right joystick forward, the drone will fly to your right, instead of flying forward. With the headless mode, the drone has a fixed “head.” In Headless Mode, the drone always remembers the side its head points to during takeoff as the front side. This means that if the drone takes off with its head pointing forward, it doesn’t matter how the drone is oriented in the air, when you push the right joystick forward, the drone will fly forward. Or, when its head is pointing to you, if you push the right joystick to the left, the drone will fly to your left.
AlTITUDE-HOLD FUNCTION
The drone is designed with altitude-hold function so the drone can maintain its altitude after you release the left joystick (the left joystick will automatically spring back to the middle).
-22-
ATTITUDE ADJUSTMENT
TRIMMER
The Forward Trim
short press
If the drone tends to drift forward:
1. Press the ( ) button one time.
2. Wait 2 seconds to watch the drone’s movement. If it still drifts, press
the button again.
3. Depending on how the drone drifts, it may take several presses to
balance the drone.
4. Repeat STEP 1 & 2 until the drone drifts forward no more.
- You can also fix the Backward/Sideward Trim using a similar method, i.e., pressing the trim button whose direction is opposite to the direction the drift.
Trim adjustments are designed to counter drifts not caused by airflow.
-23-
SPECIFICATIONS
DRONE Model: D11 Weight: 31g Max Flight Time: 8 minutes (per battery) Motor
Model: 615 Operating Temperature Range: 14° to 104°F (-10° to 40°C) Size:
928032mm
DRONE BATTERY Capacity: 390mAh Voltage: 3.7V Battery Type: Lithium-ion Polymer Battery Charging Temperature Range: 41° to 104°F (5° to 40°C) Charging Time: 60 minutes (depends on charging power and remaining battery power)
TRANSMITTER Operating Frequency: 2452-2474 MHz Flight Distance: 131 ft (outdoors and unobstructed) Operating Temperature Range: 14° to 104°F (-10° to 40°C) Battery Type: 3*1.5V AAA Battery (Not included)
USB CHARGING CABLE Input: 5V/1A Rated Power: 5 W
-24-
CONTACT US
Please do not hesitate to contact us if you need further support. 4:00 PM ~
7:00 AM (PST) usa@deerc.com (USA) eu@deerc.com (EU) +1(855)777-8866
For online support, please scan this code with Live Chat.
-25-
GENERAL INFORMATION
FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
The Supplier’s Declaration of Conformity is available at the following
address: https://www.deerc.com/Download/US/D11_FCC_sDoC.pdf.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
set to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy, if not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can not be determined by turning the
equipment off and on, the user is encouraged to try one or more of the
following measures: —Reorient or relocate the receiving antenna. —Separation
more distance between the equipment and receiver. —Connect the equipment to an
outlet on a circuit different from the receiver. —Consult the dealer or an
experienced radio/TV technician for help.
-26-
GENERAL INFORMATION
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
RF Exposure The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This device should be installed and
operated with minimum distance 20cm between the radiator & your body.
IC Notice: This device complies with Canada Industry licence-exempt RSS
standard (s). Operation is subject to the following two conditions: (1) this
device may not cause interference; and (2) this device must accept any
interference. Including interference that may cause undesired operation of the
device.
CAN ICES-003 (B) Avis d’Industrie Canada Le présent appareil est conforme aux
CNR d’industrie Canada applicables aux appareils radio exem pts de licence
L’exploitation est autorisée aux deux conditions suivantes: 1) I’appareil ne
doit pas produire de brouillage; et 2) I’utillsateur de I’appareil doit
accepterbrouillage radioélectrique subi meme si le brouillage est susceptible
d’encompromettre le fonctionnement. mauvais fonctionnement de I’appareil. Cet
appareil numériquie de la classe B est conforme à la norme NMB-003 du Canada.
-27-
GENERAL INFORMATION
CAN NMB-003 (B) RF Exposure Radiation Exposure Statement: This equipment
complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator & your body.
Déclaration d’exposition aux radiations: Cet équipement est conforme aux
limites d’exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre lasource de rayonnement et votre corps.
HOW TO RECYCLE THIS PRODUCT This symbol on the product or its documentation
indicates that it MUST not be disposed of together with household waste.
Uncontrolled waste disposal may harm the environment or human health. Please
separate your device from other types of waste for recycling it responsibly.
This will help to foster the sustainable re-use of material resources. We
suggest you contact your retailer, inquire at your local town hall or business
store to find out where and how the drone can be recycled.
-28-
GENERAL INFORMATION
BATTERY WARNING: 1. Failure to follow all the instructions may result in
serious injury, irreparable damage to the battery may cause a fire, smoke or
explosion as well. 2. Always check the battery’s condition before charging or
using it. 3. Please replace the battery if the battery is dropped or has any
peculiar smell, overheating, discoloration, deformation or leakage happens. 4.
Never use anything other than the approved LiPo charger to charge the battery.
Always use a balancing charger for LiPo cells or a LiPo cell balancer. It is
recommended that you use the one provided with the product. 5. The battery
temperature must never exceed 60°C(140°F) otherwise the battery could be
damaged or ignited. 6. Never charge the battery on a flammable surface, near
flammable products or inside a vehicle (preferably place the battery on a non-
flammable and non-conductive surface). 7. Never leave the battery unattended
during the charging process. Never disassemble or modify the housing’s wiring,
or puncture the cells. Always ensure that the charger output voltage
corresponds to the voltage of the battery. DO NOT short circuit the batteries.
8. Never expose the Li-Po battery to moisture or direct sunlight, or store it
in a place where temperatures could exceed 60°C(car in the sun, for example).
9. Always keep it out of reach of children. 10. Improper battery use may
result in a fire, explosion or other hazards. 11. Non-rechargeable batteries
are not allowed to be recharged. Rechargeable batteries should be charged
under adults’ supervision. 12. DO NOT mix different types of batteries
including the new and used ones.
-29-
GENERAL INFORMATION
13. Batteries MUST be inserted with the correct polarity. 14. The supply
terminals MUST not to be short-circuited. Regular examination of transformer
or battery charger for any damage to their cords, plugs, enclosures and other
parts MUST be done. If there is damage, they MUST not be used until the damage
has been repaired. 15. The packaging has to be kept since it contains
important information. 16. This toy should only be connected to the equipment
with symbol Class II.
EU RF Power(EIRP): 10 dBm (2452MHz ~ 2474 MHz)
Caution 1. The max operating of the EUT is 45°C, and shouldn’t be lower than
-10°C. 2. The device complies with RF specifications when the device used at
0mm from your body. 3. Declaration of Conformity.
-30-
GENERAL INFORMATION
We, Xiamen Huoshiquan Import & Export CO.,LTD hereby, declare that the
compliance of the essential requirements with the Directive 2014/53/EU, the
RoHS Directive 2011/65/EU and Safety Directive 2009/48/EC have been fully
fulfilled on our product with indication below: Product Name: Remote control
four axis series Model/Mark: D11/DEERC The Statement of compliance is
available at the following address:
http://www.deerc.com/Download/CE/D11_EU_DOC.pdf
This product can be used among EU member states.
MANUFACTURER INFORMATION Manufactured by Xiamen Huoshiquan Import & Export
CO.,LTD. Address: Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road,
Siming District, Xiamen, China +1(855)777-8866
MADE IN CHINA(CN) -31-
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>