Gear4music COSMOS-COB-MKII Cosmos COB Party Lighting System User Manual

Gear4music COSMOS-COB-MKII Cosmos COB Party Lighting System

WARNING!
Do not open cover. No user-serviceable parts inside. Refer servicing to qualified service personnel Do not place the product in a location near a heat source such as a radiator, or in an area subject to direct sunlight, excessive dust, mechanical vibration or shock The product must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product No naked flame sources, such as lighted candles, should be placed on the product Allow adequate air circulation and avoid obstructing vents (if present) to prevent internal heat build-up. The ventillation must not be impeded by covering the appliance with items such as newspapers, table-cloths, curtains etc. The mains plug is used to disconnect the appliance from the mains supply. Ensure that the mains outlet is easily- accessible and remove the plug from the mains outlet if you notice any abnormality with the appliance.

INTRODUCTION

Thank you for purchasing the Cosmos COB 4 x 30W Stage Bar by Gear4music. To get the most out of your product, please read this manual carefully.

CONTENTS

• 1 x Cosmos COB 4 x 30W Stage Bar
• 1 x Footswitch remote
• 1 x Stand
• 1 x Case
• 1 x UK IEC Cable
• 1 x EU IEC Cable

FEATURES

• 4 x 30W 4-in-1 LED lights with 120 degree beam angle
• 1, 3, 7, 12 & 16 channel modes available
• Includes Auto And Sound Reactive Modes With A Variety Of Show Modes
• Tripod Stand, Footswitch And Case Included

FUNCTIONS

BACK PANEL

1. AC OUT
   Use these IEC AC outputs to power other lights.
   The total load of the whole chain must not exceed 10A.

2. AC IN
   Connect the included IEC power cable here.

3. DMX OUT
   3-Pin Male XLR output to pass DMX signals on to another light.

4. DMX IN
   3-Pin Female XLR input to receive DMX signals from another light or controller.

5. FOOTSWITCH REMOTE INPUT
   Input port for the included Footswitch Controller

6. CONTROL PANEL
   Used to control various aspects of the COSMOS COB

7. MICROPHONE
   The microphone detects ambient audio for the sound reactive functions

CONTROL PANEL

1. MENU button
2. DOWN button
3. UP button
4. ENTER button

BACK PANEL

1. MENU
   Cycles through MENU options.

2. UP Cycles
   through the settings chosen by the MENU button.

1. Synchronous strobe (White)
2. Sound reactive strobe (White) 3.Sound reactive strobe (Colour)

| 1. Red| Show 1| Speed 1
2. Green| Show 2| Speed 2
3. Blue| Show 3| Speed 3
4. Red + Green| Show 4| Speed 4
5. Red + Blue| Show 5| Speed 5
6. Green + Blue| Show 6| Speed 6
7. Red + Green + Blue| Show 7| Speed 7
8. Sound reactive| Show 8| Speed 8
3. SUSPEND
Pauses operation of the COSMOS COB (black out).

BASIC OPERATION

Press the MENU button to bring up the menu system on the LCD Display. Use the DOWN and UP BUTTONS to navigate to your desired choice and the ENTER button to select.
Please note, if you wish to use SHOW mode then you must first set the light as a master (see the Menu Flow Diagram as to how).

MENU ITEMS

1. – DMX 512 Address
   Select the ADDR option with the ENTER button.
   Use the UP & DOWN buttons to choose the address. Press the ENTER button to save your selection. Once saved, press and hold MENU button to return to the main menu.

2. – Channel Mode
   Select the CHMD option with the ENTER button.
   Use the UP & DOWN buttons to choose your mode, such as 1, 3, 7, 12 & 16 channel modes.
   Press the ENTER button to save your selection.
   Once saved, press and hold the MENU button to return to the main menu.

3. – Slave Mode
   Select the SLMD option with the ENTER button.
   Use the UP & DOWN buttons to choose between Master, Slave 1 or Slave 2 modes. Press the ENTER button to save your selection. Once saved, press and hold the MENU button to return to the main menu.

4. – Show Mode
   Select the SHMD option with the ENTER button.
   Use the UP & DOWN buttons to choose between shows 1-8. Show 0 will play shows at random.
   Press the ENTER button to save your selection.
   Once saved, press and hold the MENU button to return to the main menu.

5. – Sound Reactivity
   Select the SOUN option with the ENTER button.
   Use the UP & DOWN buttons to choose between the sound reactive functionality being on or off.
   Press the ENTER button to save your selection.
   Once saved, press and hold the MENU button to return to the main menu.

6. – Microphone Sensitivity
   Select the SENS option with the ENTER button.
   Use the UP & DOWN buttons to adjust the sensitivity of the onboard microphone from 0 to 100. Press the ENTER button to save your selection. Once saved, press and hold the MENU button to return to the main menu.

7. – Standby Mode
   Select the BLMD option with the ENTER button.
   Use the UP & DOWN buttons to choose between the standby mode (YES) or normal mode (NO).
   Press the ENTER button to save your selection.
   Once saved, press and hold the MENU button to return to the main menu.

8. – LED Screen on/off
   Select the LED option with the ENTER button.
   Use the UP & DOWN buttons to choose between the display being ON or OFF. Press the ENTER button to save your selection. Once saved, press and hold the MENU button to return to the main menu.

9. – LED Screen Invert
   Select the DISP option with the ENTER button.
   Use the UP & DOWN buttons to choose between DISP and PSID options. Press the ENTER button to save your selection. Once saved, press and hold the MENU button to return to the main menu.

10. – Test Mode
    Select the TEST option with the ENTER button.
    The COSMOS COB will run through a built-in test program. Press and hold the MENU button to end the test and return to the main menu.

11. – Length of Operation
    Select the HOUR option with the ENTER button.
    The display will show the operating time of the COSMOS COB. Press and hold the MENU button to return to the main menu.

12. – Firmware Version
    Select the VER option with the ENTER button.
    The display will show firmware version of the COSMOS COB. Press and hold the MENU button to return to the main menu.

MASTER/SLAVE MODE

The COBMOS COB can be used in either master or slave modes allowing you to control a large ranges of lights with just a few control changes.

In master mode the COSMOS COB will transmit its settings and data via the DMX OUT connector to any other lights connected in slave mode.

In slave mode the COSMOS COB will react to incoming signals and data received via the DMX IN connector, allowing it to be controlled by external hardware such as a DMX controller or other light.

DMX CONTROL

1 CHANNEL MODE
CH1| 000-007| None
008-037| Show 1
038-067| Show 2
068-097| Show 3
098-127| Show 4
128-157| Show 5
158-187| Show 6
188-217| Show 7
218-247| Show 8
248-255| Cycle through show 1-8
3 CHANNEL MODE
CH1| 000-255| RED brightness 0-100%
CH2| 000-255| GREEN brightness 0-100%
CH3| 000-255| BLUE brightness 0-100%
7 CHANNEL MODE
CH1| 000-255| RED brightness 0-100%
CH2| 000-255| GREEN brightness 0-100%
CH3| 000-255| BLUE brightness 0-100%
CH4| 000-255| Overall brightness 0-100%
CH5| 000-007| No change
008-247| Strobe speed, slow to fast
248-255| Sound reactive strobe mode
CH6| 000-007| No change
233-247| LED colour change, 1-16
248-255| Sound reactive show mode, show 1-16
CH7| 000-007| No change
008-255| Speed, slow to fast
Channel| 12 CHANNEL| 12 CHANNEL| Function
---|---|---|---
12/16 CHANNEL MODE
CH1| CH1| 000-255| PAR 01 RED brightness 0-100%
CH2| CH2| 000-255| PAR 01 GREEN brightness 0-100%
CH3| CH3| 000-255| PAR 01 BLUE brightness 0-100%
CH4| CH4| 000-255| PAR 02 RED brightness 0-100%
CH5| CH5| 000-255| PAR 02 GREEN brightness 0-100%
CH6| CH6| 000-255| PAR 02 BLUE brightness 0-100%
CH7| CH7| 000-255| PAR 03 RED brightness 0-100%
CH8| CH8| 000-255| PAR 03 GREEN brightness 0-100%
CH9| CH9| 000-255| PAR 03 BLUE brightness 0-100%
CH10| CH10| 000-255| PAR 04 RED brightness 0-100%
CH11| CH11| 000-255| PAR 04 GREEN brightness 0-100%
CH12| CH12| 000-255| PAR 04 BLUE brightness 0-100%
 | CH13| 000-255| Overall brightness 0-100%
CH14| 000-007| No change
008-247| Strobe speed, slow to fast
248-255| Sound reactive strobe mode
CH15| 000-247| No change
248-255| LED colour change, 1-16
CH16| 000-255| Sound reactive show mode, show 1-16

SPECIFICATIONS

POWER CONSUMPTION. . . . . . . . . . . . . . . 130W
PAR LED . . . . . . . . . . . . . . . . . . . . . 4 x RGB 30W
LED . . . . . . . . . . . . . . . . . . . . . . . . . R – 360nm / 310lm, G – 515nm / 450lm, B – 460nm / 160lm
BEAM ANGLE. . . . . . . . . . . . . . . . . 120 degrees
POWER LINKING. . . . . . . . . . . . . . 5 x COSMOS-COB or 10A max total load
DMX CHANNEL MODES. . . . . . . . . . . . . . . . . . . . . . 1, 3, 7, 12, 16
POWER INPUT. . . . . . . . . . . . . . . . 220-240V AC 50/60Hz
FUSE. . . . . . . . . . . . . . . . . . . . . . . . . T 3.15A 250V
STAND SIZE. . . . . . . . . . . . . . . . . . . 1.5-2m adjustable
WEIGHT. . . . . . . . . . . . . . . . . . . . . . 11.2kg

KETTLESTRING LANE | YORK | YO30 4XF | UNITED KINGDOM METALLVÄGEN 45A | 195 72 ROSERSBERG | STOCKHOLM | SVERIGE LAHNSTRAßE 27 | 45478 MÜLHEIM AN DER RUHR | DEUTSCHLAND

If you have any more questions about this product, please do not hesitate to contact the Gear4music Customer Service Team on: +44 (0) 330 365 4444 or info@gear4music.com

Documents / Resources

| Gear4music COSMOS-COB-MKII Cosmos COB Party Lighting System [pdf] User Manual
COSMOS-COB-MKII, Cosmos COB Party Lighting System, Party Lighting System, Lighting System, Party Lighting
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>