Pepperl Fuchs VIM62PP Vibration Sensor User Manual

Pepperl Fuchs VIM62PP Vibration Sensor

Product Information

• Product Name: Vibration sensor VIM62PP-E1V16-0PE-I420V15
• Extended temperature range
• Screw-in thread for simple installation
• Simple electrical commissioning
• Rugged stainless steel housing
• Vibration velocity in mm/s via root mean square formation (rms)
• Suitable for use in hazardous area up to Zone 1/21 with type of protection intrinsic safety
• Vibration sensor with analog current output, increased temperature resistance, suitable up to Zone 1/21 with type of protection intrinsic safety

Product Usage Instructions

To use the Vibration sensor VIM62PP-E1V16-0PE-I420V15, follow the instructions below:

1. Make sure the ambient temperature is within the permissible range.
2. Install the sensor by screwing it in using the provided thread.
3. Connect the sensor to a power source with an operating voltage between 10 and 30 V DC.
4. Ensure the maximum current consumption does not exceed 25 mA.
5. Connect the output of the sensor to the desired device using a connector.
6. For use in hazardous areas, follow the specified connection instructions and ensure compliance with the applicable approvals and certificates.
7. To measure vibration velocity, set the measuring range to 0-16 mm/s.
8. Monitor the vibration velocity output through the analog current output ranging from 4 to 20 mA.
9. Take into account the measurement accuracy and cross-sensitivity of the sensor.
10. Ensure the sensor is properly protected against shocks and vibrations according to the specified standards.

For further information and support, refer to the product manual or contact Pepperl+Fuchs Group.

Vibration sensor

VIM62PP-E1V16-0PE-I420V15

• Extended temperature range
• Screw-in thread for simple installation
• Simple electrical commissioning
• Rugged stainless steel housing
• Vibration velocity in mm/s via root mean square formation (rms) < Suitable for use in harzadous area up to Zone 1/21 with type of protection intrinsic safety

Vibration sensor with analog current output, increased temperature resistance, suitable up to Zone 1/21 with type of protection intrinsic safety

Function

The vibration sensor determines the vibration quantity using rms (root meas square) averaging. This form of quadratic averaging or pre-filtering enables precise trend statements about the condition of the application.
The sensor’s design is impressively robust against tough environmental conditions.
The stainless steel housing provides optimal protection against corrosion. The wide temperature range of the sensor enables reliable measured values even in harsh conditions.
The simple mounting allows for commissioning in any application.

Dimensions

Technical Data

General specifications

Type|  | Vibration sensor
Measuring technology|  | MEMS
Series|  | Performance Plus Line
---|---|---
Measured variable|  | Vibration velocity
Measurement range|  |
Vibration velocity| v- rms| 0 … 16 mm/s
Measurement accuracy|  | ± 0.1 mm/s (calibration point: 90% of the measuring range; 159.2 Hz)

Complies with the tolerance requirements of DIN ISO 2954 for measurement range greater than 8 mm/s

Cross-sensitivity|  | < 5 % of the partial lateral acceleration, which acts exactly 90° to the measuring axis
Frequency range|  | 10 … 1000 Hz
Averaging time|  | for v-rms: 2 s
Electrical specifications
Fusing|  | external fuse is required: 3 A , semi-time-lag , 30 V DC
Operating voltage| UB| 10 … 30 V DC
Current consumption|  | max. 25 mA
Power consumption| P0| max. 750 mW
Time delay before availability| tv| 10 s (rms filter is calculated intially with measurement data before they are available at the output)
Surge protection|  | up to 2 kV
Output 1
Output type|  | analog output, current

output of the vibration variable

Output rated operating current|  | 4 … 20 mA
Load resistor|  | ≤ 500 Ω
Standard conformity
Degree of protection|  | DIN EN 60529, IP66, IP67
Shock resistance|  | DIN EN 60068-2-27, 60 g , 6 ms
Vibration resistance|  | DIN EN 60068-2-6, 16.5 g, 10 … 1000 Hz
Approvals and certificates
IECEx approval
Equipment protection level Gb|  | IECEx CSAE 22.0042X
Equipment protection level Db|  | IECEx CSAE 22.0042X
ATEX approval|  |
Equipment protection level Gb|  | CSANe 21 ATEX 1074 X
Equipment protection level Db|  | CSANe 21 ATEX 1074 X
UL approval|  |
Ordinary Location|  | E468231 cULus Listed, Class III Power Source and limited energy , if UL marking is marked on the product. For use in NFPA 70 Applications only.

adapters providing field wiring on request

Maximum permissible ambient temperature|  | max. 60 °C (max. 140 °F)
Ambient conditions
Ambient temperature|  | -40 … 60 °C (-40 … 140 °F)
Measuring head temperature|  | -40 … 125 °C (-40 … 257 °F) directly at the mounting point
Storage temperature|  | -40 … 60 °C (-40 … 140 °F)
Mechanical specifications
Connection type|  | plug
Housing material|  | Stainless steel 1.4305 / AISI 303
Housing length|  | 82.35 mm
Housing diameter|  | 31 mm
Degree of protection|  | IP66 / IP67 only in connected state
Connector|  |
Threading|  | M12
Number of pins|  | 5
Mass|  | approx. 200 g
General information

• Use in the hazardous area
  see instruction manuals Only use accessories specified by the manufacturer.

Connection

Connection Assignment

Installation

Further Documentation
The sensor manual is also available as detailed overall documentation. Among other things, installation, grounding concepts and mounting are described there in detail.
You can access the manual via the product detail page at www.pepperl- fuchs.com.

Note
The correct electrical connection and the selection of the appropriate grounding concept are crucial for malfunction-free operation of the sensor. For detailed information you may refer to the manual of the sensor.

Accessories

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
Pepperl+Fuchs Group www.pepperl-fuchs.com
USA: +1 330 486 0001
fa-info@us.pepperl-fuchs.com
Germany: +49 621 776 1111 fa-info@de.pepperl-fuchs.com
Singapore: +65 6779 9091 fa-info@sg.pepperl-fuchs.com

References

• Pepperl+Fuchs International. Industrial Sensors, Factory Automation, Process Automation, Intrinsic Safety, Explosion Protection
• Pepperl+Fuchs International. Industrial Sensors, Factory Automation, Process Automation, Intrinsic Safety, Explosion Protection

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>