SANNCE 55BXYD201 Baby Monitor User Manual

SANNCE 55BXYD201 Baby Monitor User Manual

SAFETY INSTRUCTIONS

• Keep cord out of the reach of children (more than 3ft/0.9m away) in case of STRANGULATION.
  

• NEVER place the camera or cord in or near the crib or playpen.

• NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.

• Only use the AC adapters provided.

• Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement, etc.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce heat.

• Only use attachments and accessories specified by the manufacturer.

• Unplug this device when unused for long periods of time.

• Do not insert anything into the upgrade pinholes. This operation is only intended for professionals.

CAUTION

• NOT toys. Do not allow children to play with them. The lens and lens hood are smalll parts, keep them out of your baby’s reach at all times.
• This product is NOT intended to replace the proper supervision of children. You MUST check your child’s activity regularly.
• This product is not intended for use as a medical camera and its use should not replace adult supervision.
• Unplug the product during lightning storms.
• Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after that. Check the reception regularly. Test the camera before use and after changing the camera’s location.
• For indoor use only.
• Clean the camera with a dry cloth only.
• Do not block any ventilation openings.
• Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m/4.9ft apart.

PACKAGE CONTENTS

• 1x Baby Camera
  

• 1x LCD Monitor
  

• 1x Wall Mount

• 2x Power Adapter

• 2x 2m Type-C Power Cable

• 1x Mounting Screw Bag

• 1x User Manual

The power adapters may vary based on the specific countries’ adapter specifications.

PRODUCT DIAGRAM

LCD Monitor Introduction

1. Power/Sleep Button: Long press to turn on/off the monitor; short press to turn on/off the screen.
2. Menu/Back Button: Press to enter menu page or press as a Back 2 button.
3. Camera Switch: Switch cameras if connected with two or more cameras.
4. Charging Indicator: It gives off yellow light while the monitor is being charged.
5. Left Button: Press to pan the camera leftward or to change your selection leftward.
6. Up Button: Press to tilt the camera upward or to change your selection upward.
7. Confirm/Zoom Button: Press to Zoom in/out or to confirm your selection.
8. Right Button: Press to pan the camera rightward or to change your selection rightward.
9. Down Button: Press to tilt the camera downward or to change your selection downward.
10. Power Indicator: The green light turns on if connected to electricity.
11. Talk Button: Press to talk to your baby in the monitoring image.
12. Sound Level LED: Low/high level shows low/high sound detected by the camera.
13. Horn/Brightness Button: Press to adjust the monitor’s volume or brightness in the monitoring image.
14. Microphone
15. Antenna
16. Support Stand
17. Speaker
18. Power Input
19. Reset Hole

Camera Introduction

1. Microphone
2. Night Vision Sensor
3. Cameralens
4. LeDs
5. Nightlight
6. Pair Button
7. Power nput
8. Temperature Sensor
9. Wall Mounting Threaded Holes
10. Speaker
11. LEDButton
12. +Button
13. – Button
14. Lullabies Button

GETTING STARTED

Charging & Powering Baby Monitor

1. Connect one end of the power cable to the 5V 2A power adapter, and then link the other end of the power cable (the Type-C end) to the monitor.
2. Plug the power adapter into the outlet.
3. Unplug the unit when its power indicator turns off, indicating a full charge.Of course, if you have been plugged in, it will not affect the use, but it may affect the battery life.
4. Press the Power button on the monitor to power on with the power indicator lighting green.
   

Powering Camera

1. Connect one end of the power cable to the 5V 2A power adapter, and then link the other end of the power cable (the Type-C end) to the camera.
2. Plug the power adapter into the outlet.
   

Only use the power adapters included in the package.

• Do not place the camera and power cord within the reach of your baby.

How to Add the Camera to the LCD Monitor
By default, one camera has been paired with the monitor when manufactured. When you power on the monitor and camera, the two will automatically pair. To add more cameras.

1. Press to enter menu page, Choose and press button.
   

2. select then press button.
   

3. Selec and press button TWICE. See Camera is NOT paired, Press button to start pairing.
   

4. Press button on the back of the camera, Then see the prompted Paired.
   

• Once they’re paired successfully, the camera number with \’con@ will be shown at the top left.
• Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m/4.9ft apart.
• It is recommended to pair in the baby’s room, or wherever you intend to place the camera.
• Four cameras at most can be connected to one monitor.

Placing the Camera
For safety reasons and better vision in night vision mode, if the camera is placed on a 0.75m/2.5ft table top, the distance from the baby is at least 1.5m/4.9ft. (If the position of the camera is increased by 0.1m/0.3ft, the distance from the baby to the camera will be increased by 0.2m/0.7ft. The effective distance between the camera and the baby is within 6m/19.7ft. In the meantime, please ensure that the camera power cord cannot be touched by the baby.)

How to Install the Camera to the Wall

1. Unscrew bracket’s nut and adjust the bracket to an appropriate angle. Screw the nut again tightly.
   

2. Place the bracket on the wall, and then mark the positions on the wall.
   

3. Drill holes at the marked positions, and put anchors into the holes.
   
   Note: Anchors are not needed in the wooden wall.

4. Fix the bracket to the wall with the screws.
   

5. crew up the top bolt of bracket with the nut at the bottom of the camera.
   

6. To better match the proper viewing field, Please unscrew the nut on the side of the bracket, adjust the angle of the bracket downwards, until the baby appears in the monitoring range, tighten the nut on the side of the bracket again, and the installation is complete.
   

Don’t release the camera until you’re sure it is firmly mounted.

FUNCTIONS & OPERATIONS

Top Status Indications

| No signal connection| | Temperature alarm enabled
---|---|---|---
| Signal strength| | VOX mode is on
| Live video loop (Multiple cameras switch screens every 10 seconds)| | VOX mode is on
| Camera| | Night mode
| Current Time| | 2 times magnification
| Lullabies enabled| | 4 times magnification
| Sreen sleep enabled| | Current room temperature
| Sound detection enabled|  Battery Level
| Press and hold Button 1o talk to your baty, relecss 1t to 2xt the talking mode.
| In a standalone live stream, you can rotate the camera up & down, left & right by controlling the direction button on the monitor.

In a certain single monitoring screen, press the sub menu button to use the up/down button to adjust the brightness, the left/right button to adjust the sound volume.

Notifications Icons

| No camera connected
---|---
| Sound Alarm
| Temperature Alarm
| Feeding Notification

Short press the button for Live-Video-Loop function, then you can see on the status bar. When this function is on, the connected cameras will automatically switch every 10 seconds. And if there is a sound/temperature alarm, the camera-switch function will pause temporarily.

Baby Monitor Setting Menu
Press the power turn on the monitor, and then press . ” menu button to go to the setting menu.

Setting Menu Introduction

MEDIUM(65dB) and HIGH(60dB).LOW means the sound can be detected if it reached78dB, and so on for MEDIUM and HIGH.VOX Note: When the sound detected by the camera islower than 65dB, the display enters the standby stateat the set sleep time. The detection sound is greaterthan 65dB, the display lights up, and the alarm soundwill not be triggered. The “Screen Sleep” setting isturned off, and the VOX function is disabled.
| Temperature Alarm: indicates that the temperaturevalue for high and low temperature alarms can be set.
| Language: There are seven languages built in yourdevice, you can choose your language here.
| Lullabies: This function is to comfort baby whenneeded.
| Screen Sleep: This function is to prolong your monitor’sruntime by shutting down the screen.
| Feed: This function is to remind you of feeding yourbaby. OFF means you shut down the function; 2.5 hourmeans it reminds you every 2.5 hours and so on for theother options.
| Settings: This function is to set Date/Time, turn on/offOSD, restore factory settings and provide servicesupport information.

TROUBLESHOOTING

Q1. Baby monitor can’t connect with the camera?

• Check whether the camera is near the monitor (recommended to keep within 1.5-2m/4.9-6.6ft) Check whether the monitor is of low battery. Charge it in time to restore good connection. Check whether the camera is well connected to power. Check whether there are any large metallic objects including doors, refrigerators, mirrors, etc., are placed between the camera and monitor thus blocking the radio signals. Check whether there’s any other 2.4GHz product is used nearby like WiFi routers, microwave ovens, which may interfere the connection. “ If nothing above is involved, please retry to pair.

Q2. Product not powering on?

• Check that the camera and monitor are turned on. Check the camera is connected to power properly (it cannot be charged:; it's power off once disconnected from power). Check that the monitor is of enough battery (When the battery level icon flashes red slowly on the display, it will automatically turn off in about 15 minutes).

Q3. Nothing shown when | view a camera?

• Check all connections to the camera (power cable plugging and pairing). Check whether the screen is in sleep mode. Press any button to awake it. Check whether the camera is within range of the monitor. * Adjust the monitor antenna to vertical position for better signal transfer.

Q4. Black and white pictures?

• Night vision LED may be ON. Please turn on room lights to force it out of the night mode.

@5. No sound from the monitor?

• Check whether the system sound volume is set High or Low. It'll be mute if set so.

Q6. Too much noise?

• Volume may be set too high. Press Shortcut Button -> Left Button to volume down. * The camera and monitor may be put too close; keep them at least 1.5m/4.9ft apart.

Q7. Choppy videos?

• Check whether the camera is near the monitor and that there are no obstacles between them. * Adjust the monitor antenna to vertical position for better signal transfer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>