HEALTHCARE LIGHTING HPCG Textures Ceiling Mount Instruction Manual

: June 13, 2024
: HEALTHCARE LIGHTING

Table of Contents

HEALTHCARE LIGHTING HPCG Textures Ceiling Mount
Product Information
Important Safety Instructions
Product Usage Instructions
SAFETY INSTRUCTIONS
Installation Steps
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HEALTHCARE LIGHTING HPCG Textures Ceiling Mount

HEALTHCARE-LIGHTING-HPCG-Textures-Ceiling-Mount-
PRODUCT

Product Information

Product Name: Healthcare Lighting HPCG
Manufacturer: HealthCare Lighting
Manufacturer Address: One Lithonia Way, Conyers, GA 30012
Manufacturer Phone: 800-315-4963
Manufacturer Website: www.acuitybrands.com.
Revision: B
Revision Date: 10/11/2021

Important Safety Instructions

Disconnect or turn off power before installation or servicing to avoid the risk of electric shock.
Verify that the supply voltage is correct by comparing it with the luminaire label information.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
All wiring connections should be capped with UL-approved recognized wire connectors.
Wear gloves and safety glasses at all times when removing luminaire from the carton, installing, servicing, or performing maintenance to avoid the risk of injury.
Avoid direct eye exposure to the light source while it is on.
Allow the lamp/fixture to cool before handling. Do not touch the enclosure or light source. Do not exceed the maximum wattage marked on the luminaire label. Follow all manufacturer’s warnings, recommendations, and restrictions for driver type, burning position, mounting locations/methods, replacement, and recycling to avoid the risk of burn.
Keep combustible and other materials that can burn away from the lamp/lens. Do not operate in close proximity to persons, combustible materials, or substances affected by heat or drying to avoid the risk of fire.
Never connect components under load. Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation. Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must be checked for compatibility with the luminaire prior to installation. LED fixtures must be powered directly off a switched circuit.
Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
Do not exceed the fixture’s maximum ambient temperature. Only use the fixture in its intended location.
LED products are Polarity Sensitive. Ensure proper Polarity before installation.
Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit. Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
Some components inside the fixture may not be serviceable. In the unlikely event, that your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.

Product Usage Instructions

Before installation or servicing, ensure that the power is disconnected or turned off.
Verify the supply voltage by comparing it with the information on the luminaire label.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
Cap all wiring connections with UL-approved recognized wire connectors.
When removing, installing, servicing, or performing maintenance on the luminaire, always wear gloves and safety glasses.
Avoid direct eye exposure to the light source when it is turned on.
Allow the lamp/fixture to cool before handling. Do not touch the enclosure or light source. Ensure that the maximum wattage marked on the luminaire label is not exceeded. Follow all manufacturer’s warnings, recommendations, and restrictions regarding driver type, burning position, mounting locations/methods, replacement, and recycling.
Keep combustible materials away from the lamp/lens and avoid operating the luminaire in close proximity to persons, combustible materials, or substances affected by heat or drying to prevent the risk of fire.
Never connect components under load. Mount and support the fixtures in a manner that does not cut the outer jacket or damage wire insulation. Check the compatibility of controls for dimming,auto-sensing, or remote control with the luminaire before installation. Power LED fixtures directly off a switched circuit.
Ensure proper ventilation around the fixture by allowing for some volume of airspace. Do not cover LED fixtures with insulation, foam, or any material that hinders convection or conduction cooling.
Do not exceed the maximum ambient temperature specified for the fixture. Use the fixture only in its intended location.
Pay attention to polarity when installing LED products.
Use personal grounding equipment during installation or servicing to prevent electrostatic discharge (ESD). Avoid touching individual electrical components to avoid ESD, shorten lamp life, or alter performance.
Some components inside the fixture may not be serviceable. If your unit requires service, stop using it immediately and contact an ABL representative for assistance.
Read the complete installation instructions provided with the fixture for any additional information specific to the product.

SAFETY INSTRUCTIONS

LED IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
Installation and service of luminaires should be performed by a qualified licensed electrician.
Maintenance of the luminaires should be performed by a person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
It will occasionally be necessary to clean the outside of the refractor/lens. The frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to the user. The refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water, and wiped dry. Should the optical assembly become dirty on the inside, wipe the refractor/lens and clean in the above manner, replacing damaged gaskets as necessary.
- DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
- Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise that are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING RISK OF ELECTRIC SHOCK

Disconnect or turn off power before installation or servicing.
Verify that the supply voltage is correct by comparing it with the luminaire label information.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
All wiring connections should be capped with UL-approved recognized wire connectors.

CAUTION RISK OF INJURY

Wear gloves and safety glasses at all times when removing luminaire from cartons, installing, servicing, or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

WARNING RISK OF BURN

Allow lamp/fixture to cool before handling. Do not touch the enclosure or light source.
Do not exceed the maximum wattage marked luminaire label.
Follow all manufacturer’s warnings, recommendations, and restrictions for driver type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

Keep combustible and other materials that can burn, away from lamp/lens.
Do not operate in close proximity to persons, combustible materials, or substances affected by heat or drying.

CAUTION: RISK OF PRODUCT DAMAGE

Never connect components under load.
Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must be checked for compatibility with the luminaire prior to installation. LED fixtures must be powered directly off a switched circuit.
Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
Unless individual product specifications deem otherwise: Do not exceed fixtures’ maximum ambient temperature.
Only use the fixture in its intended location.
LED products are Polarity Sensitive. Ensure proper Polarity before installation.
- Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
Some components inside the fixture may not be serviceable. In the unlikely event, that your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
Always read the fixture’s complete installation instructions prior to installation for any additional fixture-specific warnings.
Always ensure that the electrical distribution system is up to NEC (and any applicable local code)requirements.
Verify that the power distribution system has proper grounding. Lack of proper earth ground can lead to fixture failure and may void the warranty.

Choose either Part 15 OR Part 18 and move to Page 3 Installation Instructions under Delivery. Lithonia Outdoor will always use Part 15. All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation

This device complies with Part 18 of the FCC Rules but may cause interference with cordless cell phones, radios, televisions, and other electronic devices. To correct the problem, move the device away from the luminaire or plug into a different outlet. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communications equipment operating between 0.45 and 30MHz. Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

Installation Steps

Route black & red wires from the lamp assembly through the center hole on the ceiling plate and out the top of the fixture.
Mount the stem with the canopy to the lamp assembly using (4) hex nuts provided.
Loosen the set screw on a slip ring to lower the canopy spinning. Raise the fixture and attach it to the contractor-supplied j-box with (2) 8-32 screws (by others).
Make all necessary wire connections. Raise the canopy spinning and secure in place with a slip ring set screw.
Raise shade and secure with (4) hex nuts provided. Raise the bottom lens and secure it in place by screwing a decorative knob onto the bottom nipple. $HEALTHCARE-LIGHTING-HPCG-Textures-Ceiling-Mount-FIG-1 $2$$

Wiring Input Power to Remote Dimming Box:

Black, White – Line Voltage (120/277V0 Green – Ground Purple – 0-10V Dimming (+) Pink – 0-10V Dimming (-) For non-dimming installations, cap the purple and pink wires.

Wiring From Remote Box to Fixture:

Run (1) 18 AWG black & (1) 18 AWG red wire from remote box to fixture wires.
Wires between remote box and fixture are supplied by others.
Connect black wire from fixture to black wire from remote box.
Connect red wire from fixture to red wire from remote box $HEALTHCARE-LIGHTING-HPCG-Textures-Ceiling-Mount-FIG-1 $3$$