HEALTHCARE LIGHTING HPC7 Ceiling Mount Instruction Manual

HEALTHCARE LIGHTING HPC7 Ceiling Mount

Product Information

• Product Name: Healthcare Lighting HPC7
• Manufacturer: HealthCare Lighting
• Revision: B
• Model Number: I-HPC7
• Revision Date: 10112021
• Contact Information:
  • Phone: 800-315-4963,
  • Website: www.acuitybrands.com.

Product Usage Instructions

Important Safety Instructions:

• Read and follow all safety instructions.
• Save these instructions and deliver to the owner after installation.
• Disconnect or turn off power before installation or servicing.
• Verify that the supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved recognized wire connectors.
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing, or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed the maximum wattage marked on the luminaire label.
• Follow all manufacturer’s warnings, recommendations, and restrictions for driver type, burning position, mounting locations/methods, replacement, and recycling.
• Keep combustible and other materials that can burn away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials, or substances affected by heat or drying.

Additional Usage Instructions

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must be checked for compatibility with the luminaire prior to installation.
• LED fixtures must be powered directly off a switched circuit.
• Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture.
• Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
• Do not exceed the fixture’s maximum ambient temperature.
• Only use the fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
• Always read the fixture’s complete installation instructions prior to installation for any additional fixture-specific instructions.

SAFETY INSTRUCTIONS

LED IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, andother hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operationand any hazards involved. Regular fixture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambientdirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warmwater and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assemblybecome dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
  • DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have beendamaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
  • Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingencyto meet in connection with installation, operation, or maintenance.
• Should further information be desired or shouldparticular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should bereferred to Acuity Brands Lighting, Inc.

WARNING RISK OF ELECTRIC SHOCK

• Disconnect or turn off power beforeinstallation or servicing.
• Verify that supply voltage is correct bycomparing it with the luminaire labelinformation.
• Make all electrical and groundedconnections in accordance with the NationalElectrical Code (NEC) and any applicablelocal code requirements.
• All wiring connections should be cappedwith UL approved recognized wireconnectors.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all timeswhen removing luminaire from carton,installing, servicing or performingmaintenance.
• Avoid direct eye exposure to the light sourcewhile it is on.

WARNING RISK OF BURN

• Allow lamp/fixture to cool before handling.Do not touch enclosure or light source.
• Do not exceed maximum wattage marked onluminaire label.
• Follow all manufacturer’s warnings,recommendations and restrictions for: drivertype, burning position, mountinglocations/methods, replacement andrecycling.

CAUTION RISK OF FIRE

• Keep combustible and other materials thatcan burn, away from lamp/lens.
• Do not operate in close proximity to persons,combustible materials or substancesaffected by heat or drying.

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to theluminaire must be checked for compatibility with the luminaire prior to installation. LED fixtures must bepowered directly off a switched circuit.
• Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for somevolume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material thatwill prevent convection or conduction cooling.
• Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambienttemperature.
• Only use fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be wornduring all installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alterperformance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may requireservice, stop using the unit immediately and contact an ABL representative for assistance.
• Always read the fixtures complete installation instructions prior to installation for any additional fixturespecific warnings.
• Always ensure that the electrical distribution system is up to NEC (and any applicable local code)requirements.
• Verify that power distribution system has proper grounding. Lack of proper earth ground can lead to fixturefailure and may void warranty.

Choose either Part 15 OR Part 18 and move to Page 3 Installation Instructions under Delivery. Lithonia Outdoor will always use Part 15. All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation

This device complies with Part 18 of the FCC Rules but may cause interference with cordless and cell phones, radios, televisions, and other electronic devices. To correct the problem, move the device away from the luminaire or plug into a different outlet. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communications equipment operating between 0.45-30MHz.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

The HPC7 is designed to mount to a 2-1/8” deep octagon box, flush mounted to the ceiling surface. *Do not install this luminaire outdoors unless equipped with the ‘WL’ Wet Location option!

Installation Steps

1. Refer to the wiring diagrams on the next page to determine the appropriate connections for the project.
2. Connect supply wires to driver input wires (A) per wiring diagram.
3. Attach mounting plate (B) to octagon box so that driver (A) is located within the box.
4. Connect polarized plug (D) from luminaire to socket on driver (A).
5. Align threaded studs (E) with sockets (C) on mounting plate. Wet Label: Ensure gasket (F) is fully seated around canopy.
6. Install luminaire by guiding studs (E) into sockets (C) and pressing firmly until the luminaire is flush with the ceiling surface.
7. Thread acrylic diffuser (I) onto fitter (H) being careful to avoid touching the LED module. Do not over-tighten.
   • Wet Label: Ensure Gasket (F) is pressed firmly against wall. Use silicone sealant between luminaire and wall to make switchbox water-tight.

Maintenance & Cleaning

No regular maintenance is required. The LED module & driver are non- serviceable components with a 50,000 hours operating life to 70% initial output. At 100,000 hours light output will be approximately 50% of initial. Clean the fixture with a soft cloth moistened with mild soap and water.

Wiring:
POWER SUPPLY / DIMMING
This model is available with Dimming driver in both 120V and 277V input versions. Dimming drivers require a 0-10V fluorescent-type dimming control. For non-dimming installations, cap the purple and pink wires

INSTALLATION

NON-DIMMING INSTALLATIONS

• Connect WHITE wire to power NEUTRAL.
• Connect BLACK wire to power HOT.
• Connect GREEN wire to power GROUND.

Read all instructions before installation. Do not make live connections !

DIMMING INSTALLATIONS

• The integral dimming driver is designed to the 0-10V IC dimming specification 60929 and is compatible with common 0-10V dimmers and dimming systems. Do NOT connect line voltage to dimming input wires.
• Connect WHITE wire to power NEUTRAL
• Connect BLACK wire to power HOT.
• Connect VIOLET wire to POSITIVE INPUT of Dimming Control.
• Connect PINK wire to NEGATIVE INPUT of Dimming Control.

CONTACT

• HealthCare Lighting One Lithonia Way,
• Conyers, GA 30012
• Phone: 800-315-4963
• www.acuitybrands.com.
• Revision B I-HPC7
• Revision Date 10112021

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• U.S. Environmental Protection Agency | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>