RELIABILT 90180-036 Bragg Matte Black Single Cylinder Electronic Deadbolt Lighted Keypad Instruction Manual

RELIABILT 90180-036 Bragg Matte Black Single Cylinder Electronic Deadbolt

Lighted Keypad

Product Information

• The product is equipped with default codes for programming and user access.
• However, it is highly recommended to replace these default codes with your own personalized codes for enhanced security.

Product Usage Instructions

To replace the default Programming Code and default User Code, follow these steps:

1. Access the programming mode by entering the default Programming Code.
2. Once in programming mode, locate the option to change the codes. This may vary depending on the specific product model.
3. Enter the new code of your choice using the provided keypad or other input method.
4. Confirm the new code by re-entering it to ensure accuracy.
5. Save the changes and exit the programming mode.

By following these instructions, you will be able to replace the default Programming Code and default User Code with your own personalized codes, ensuring enhanced security for your product.

SAFETY INFORMATION

• Please read and understand this entire manual before attempting to assemble, operate, or install the product.

PREPARATION

• Before beginning installation of the product, make sure all parts are present. Compare parts with the package contents list.
• If any part is missing or damaged, do not attempt to assemble, install, or operate the product. ESTIMATED ASSEMBLY TIME: 40 – 60 MINUTES

CARE AND MAINTENANCE

THE FOLLOWING CARE INSTRUCTIONS SHOULD BE FOLLOWED TO ENSURE A LONG-LASTING FINISH:

1. Remove locks, or do not install locks, prior to painting your door
2. Periodically clean with mild soap and a soft cloth only Do not use abrasives or harsh chemicals and avoid sharn open

USER GUIDE

Do not use any chemical liquid or lubricating oil with additives to clean the lock body. It will damage the surface or even the mainboard.

UNIT INTERFACE

1. Programming Button
   • The programming button is for entering codes, clearing errors, and setting functions.
   • It is also used to lock the door.
2. Number Buttons
   • To enter user codes. Each user code is 4-10 digits in length.
3. Cylinder
   • To lock/unlock the lockset from outside
4. Washer
   • Prevents water from permeating into the lockset.
5. Battery Lid
   • Slide the lid to change the batteries.
6. Battery Holder
   • Four AA (1.5 V) alkaline batteries.
7. R Button (Reset)
   • Restore default settings.
8. Turn-piece
   • To lock/unlock the lockset from inside.

OPERATING INSTRUCTIONS

• Keep the door open while programming to avoid being locked out accidentally.
• The lock contains one factory-preset user code but can be programmed to store up to a total of ten additional unique use codes.
• Codes can be added and deleted at any time. For first-time programming, use factory default programming code.
• It’s recommended to change the default programming code and default user code right after you install the lock.

Operation Indicator Sounds and Lights

• Default programming code (PC): 0000 Default user code (UC): 1234
• Your new programming code (PC)———————————————–
• Your new user code (UC)——————————————
• The same programming code and user code cannot be accepted.
• The lock will cease operation if unauthorized codes are entered over 5 times. The system will unfreeze after 45 seconds.

Door Handing Identification Process

• The lock needs to learn if your door is right-handed or left-handed.
• Change Programming Code
• Add New User Code
• Note: Up to 10 sets of user codes can be saved. User codes should be 4-10 digits in length.
• IMPORTANT: It is recommended that you replace the default Programming Code and default User Code with codes of your own.
• Delete an Existing User Code

Delete All User Codes at Once

• Note: Auto-locking and keypad-locking functions will be invalid when user codes are deleted. The lock can only be operated by key during that time.

Toggle Auto-Lock On/Off

• Note: The preset delay time is 30 seconds, you can change the time by following instruction #7. Repeat the steps in #6 to cancel the auto-locking function.

Set Auto-Lock Time Delay

• Note: 10-99 seconds delay-time available.

Toggle Mute On/Off

• Note: Repeat same steps in #8 to turn beeper On/Off. LED illumination is still functioning when it’s in mute, but there will be no warning alarms

Enable/Disable All User Codes

Note: Auto-locking and keypad-locking functions will be invalid when user codes are disabled.

Create a One-Time User Code 4-10 Digits Long

Note: The one-time user code will automatically cancel after it is used one time.

Restore Default Settings

Press

• Note: Press the button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps.
• After restoring default settings, you must run the door-handling identifying process (#1) again before programming any other functions.

TROUBLESHOOTING

LIMITED LIFETIME WARRANTY

The Manufacturer extends a Limited Lifetime Mechanical and Finish Warranty to the original “User” of this product against defects in materials and workmanship as long as the User occupies the residential premises upon which the product was originally installed. Upon return of a defective product to the Manufacturer, the Manufacturer shall either replace, repair or refund the purchase price in exchange for the product. This warranty does not cover abused or misused products or those products used in commercial applications. No other warranties, express or implied are made with respect to the product including but not limited to any implied warranty of merchantability or fitness for a particular purpose. The Manufacturer DOES NOT authorize any person to create for it any obligation or liability in connection with the product. The Manufacturer maximum liability here under limited to the purchase price of the product, and in no event shall the company be liable for any consequential, indirect, incidental or special damages of any nature arising from the sale or use of this product, whether in contract, tort, strict liability or otherwise.

Questions

Call customer service at 1-866-386-7941, 8:00 a.m. – 8:00 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>