GEORGE KOVACS P5601-884-L Topknot 3-Light Black and Brushed Gold Pan Integrated LED Shaded Pendant Light Instruction Manual

GEORGE KOVACS P5601-884-L Topknot 3-Light Black and Brushed Gold Pan

Integrated LED Shaded Pendant Light

Product Information:

• Product Name: P5601-884-L LED Pendant
• Installation Instructions for P5601-884-L For LED Pendant
• Product Set: Set# A-020-225
• Includes: Mounting plate, Ground Screw, Mounting Screw*4, Glass#-PG5601
• Dimmable: Yes, with ELV and/or LED-compatible wall dimmer switches.

Product Usage Instructions

1. Before starting the installation process, make sure to read and save these instructions.
2. Ensure that the power is shut off at the fuse or circuit breaker before proceeding with the installation.
3. Refer to Fig 1 for a visual representation of the product.
4. Connect the electrical wires as shown in Fig 2.
   • Make sure all wire connectors are secured.
   • If your junction box has a ground wire (green or bare copper), connect the ground wire from the fixture to it.
   • If there is no ground wire in the junction box, connect the fixture ground wire directly to the mounting plate (A) using the provided green screw (D).
   • Tuck the wire connections neatly into the junction box.
5. Once the wiring is complete, your installation is now complete.
6. Return power to the junction box.
7. Test the fixture to ensure it is functioning properly.
8. When handling the fixture, do not apply pressure to the LEDs.
9. Hold the fixture by the frame only.
10. It is important to note that fixtures should be installed by a qualified electrician to ensure proper wiring and installation.

INSTALLATION INSTRUCTIONS

FOR P5601-884-L

For LED Pendant
READ AND SAVE THESE INSTRUCTIONS

WARNING ISHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

ASSEMBLING THE FIXTURE

(Fig.1)

1. Shut off power at the fuse box or circuit breaker. Remove the old fixture including the mounting hardware.

2. Carefully remove the fixture from the carton and check that all parts are included as show in Figure 1.

3. Unscrew screws (G) to remove mounting plate (A) from the canopy (F).
   Position mounting plate (A) onto ceiling and mark the location of two plastic anchors (I). Pre-drill the holes for plastic anchors (I). Then insert plastic anchors (I) into ceiling. Attach mounting plate (A) to the junction box (not included) using the mounting screws (B, size 8#-32N 1″). The side of the mounting plate (A) marked “GND” must face out as shown in Fig.1. Secure mounting plate (A) by screwing wood screws (H) through the holes on mounting plate (A) into plastic anchors (I).

4. The length of the power cord can be adjusted by loosening set screw (E), then tighten set screw (E) to secure the cord.

5. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (J) on the end of support cable (K) into a slot located on mounting plate (A). Carefully allow the support cable (K) to support the weight of the fixture while wiring (Fig.1).
   CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wire as shown in Fig 2. Making sure that all wire connectors and secured. If your junction box has a ground wire (green or bare copper), connect the ground wire from the fixture to it. Otherwise connect fixture ground wire directly to mounting plate (A) using green screw (D) provided. Tuck the wire connections neatly into the junction box.

Your installation is now complete. Return power to the junction box and test the fixture.

CAUTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the frame only.

IMPORTANT: Fixtures should be installed by a qualified electrician to ensure proper wiring and installation.
Dimmable with ELV and/or LED-compatible wall dimmer switches.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>