GEORGE KOVACS P1551-66A-L Trizay 24 in 1 Light Black LED Vanity Light

Product Information

The product is a light fixture with three different models : P1551-66A-L, P1552-66A-L, and P1553-66A-L. It comes with a set of mounting hardware and a glass shade. The fixture is dimmable with ELV and/or LED compatible wall dimmer switches.

Package Contents

• Mounting plate
• Junction box screw (2 pcs)
• Ground Screw
• Outlet box
• Glass Shade (#PG1551 for P1551-66A-L, #PG1552 for P1552-66A-L, #PG1553 for P1553-66A-L)

Additional Tools Needed (Not Included)

• Screwdriver

Product Usage Instructions

Preparation

1. Shut off power at the fuse box or circuit breaker box.
2. If necessary, remove the old fixture and mounting hardware.

Mounting the Fixture (Fig. 1)

1. Secure the mounting plate (A) to the outlet box using the outlet box screws (B).
2. The side of the mounting plate marked GND must face out.

Connecting the Wires (Fig. 2)

1. Connect the electrical wires as shown in Fig. 2, ensuring that all wire connectors are secured.
2. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
3. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
4. After wires are connected, tuck them carefully inside the outlet box.

Finishing the Installation (Fig. 1)
Place the back plate (C) over the mounting plate (A) and secure it with screws (D).

Replacing LED Module (Fig. 3)

Note: This step should be performed by a qualified electrician.

1. Shut off the power.
2. To remove the fixture body from the wall, loosen screws (D) and back plate (C) from mounting plate (A).
3. Disconnect wire connectors and place the fixture body on a clean surface.
4. Remove screws (E) and the metal caps (H) from the fixture body and remove the glass (F).
5. Press the button with printed “L” quick connector on the LED module (G) with a screwdriver to disconnect the black wire and then disconnect the white wire from the printed “N” quick connector on the LED module (G).
6. Carefully remove the LED module (G) from the base.
7. Reverse steps a-d for installing the new LED module.

Your installation is now complete. Return power to the outlet box and test the fixture.

PREPARATION

1. Shut off power at the fuse box or circuit breaker box. If necessary, remove the old fixture and mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
   MOUNTING THE FIXTURE (FIG. 1)

3. Secure mounting plate (A) to the outlet box (not included) using outlet box screws (B) (Size: #8-32N*L1”L). The side of the mounting plate marked “GND” must face out.
   CONNECTING THE WIRES (FIG. 2)

4. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After wires are connected, tuck them carefully inside the outlet box.
   FINISHING THE INSTALLATION (Fig. 1)

5. Place back plate (C) over mounting plate (A) and secure with screws (D).

Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.)

• Shut off the power.
• To remove fixture body from wall, loosen screws (D) and back plate (C) from mounting plate (A). Disconnect wire connectors and place fixture body on a clean surface (Fig.1).
• Remove screws (E) and the metal caps (H) from the fixture body and remove glass (F).
• Press the button with printed ”L” quick connector on LED module
• with screwdriver (not included) to disconnect the black wire and then disconnect the white wire from the printed ”N” quick connector on LED module (G). Carefully remove LED module (G) from the base.
• Reverse steps a-d for installing the new LED module.

Your installation is now complete. Return power to the outlet box and test the fixture.

Note: The illustration in figure 1 on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer switches

Fig. 1
Set #A-020-150A for item# P1551-66A-L Set #A-020-300 for item# P1552-66A-L Set

A-020-400 for item# P1553-66A-L

• Mounting plate
• Junction box screw* 2 pcs
• Ground Screw Outlet box

Glass Shade #

• PG1551 for item# P1551-66A-L PG1552 for item# P1552-66A-L
• PG1553 for item# P1553-66A-L

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>