Knightsbridge LPANKIT LPAN30 LED Panel Installation Guide
- June 13, 2024
- Knightsbridge
Table of Contents
Knightsbridge LPANKIT LPAN30 LED Panel
Product Information
The LPAN30 / LPANRC / LPANS / LPANKIT are products that require installation and maintenance. These instructions should be read carefully and kept for future reference and maintenance. The products include the following:
- LPAN30
- LPANRC
- LPANS
- LPANKIT
The products have safety precautions and guidelines that should be followed during installation and operation.
Safety
During installation and maintenance, it is important to follow safety
precautions to ensure the well-being of the user and the proper functioning of
the product.
Installation
- Refer to Fig. 1 for the correct wiring connections: L (Live – Brown) and N (Neutral – Blue).
- Identify the appropriate location for installation, ensuring that there are no gas/water pipes or electrical cables that could be infringed upon.
- Drill the fixing holes in the designated location, taking care not to damage any existing infrastructure.
- Securely fix the anchors to the ceiling as shown in Fig. 3.
- Use the provided corner brackets (Fig. 5) to position and secure the product.
Refer to the provided figures for visual guidance during installation.
Maintenance
Follow the general guidelines below for proper maintenance of the product:
- Check local authorities for available facilities related to maintenance.
- Refer to the warranty section for information on product coverage.
Warranty
The product comes with a warranty. For detailed warranty information, refer to
the warranty section in the user manual.
International Contact Details
If you have any further questions or need assistance, you can contact ML
Accessories Limited using the following contact details:
TA 72, ML Accessories Limited, LU5 4LT, www.mlaccessories.co.uk.
GENERAL INSTRUCTIONS
- These instructions should be read carefully and retained after installation by the end-user for future reference and maintenance.
- These instructions should be used to aid the installation of the following products: LPAN30 / LPANRC / LPANS / LPANKIT
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
- Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
- This product is for indoor use only
- Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
- This product is Class II double insulated
- This product is IP20 rated
INSTALLATION
Note
If this luminaire is being used in conjunction with an external PIR or sensor,
please confirm with the manufacturer of the sensors that they are compatible
with LED luminaires
Recessed installation into a grid ceiling
- Remove a ceiling tile
- Provide power to the required point of installation
- Remove the terminal cover on the primary side of the driver with the aid of a slotted screwdriver
- Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 1): L – Live (Brown) and N – Neutral (Blue)
- Refit the terminal cover
- Insert the panel into the ceiling and ensure it is firmly fixed
- Switch on and check for the correct operation
Recessed installation into a plasterboard ceiling using LPANRC
- Cut a 570x570mm hole in the mounting surface ensuring not to infringe with any joists, gas/water pipes or electrical cables
- Add the 4 x spring clips (LPANRC, sold separately) to the panel (see Fig. 2)
- Connect the luminaire to the mains supply as detailed above
- Lift both spring clips on one side of the luminaire and push into the ceiling, then repeat on the other side
- Switch on and check for the correct operation
Suspended installation using LPANS
- Using the anchors of the suspension kit (LPANS, sold separately) as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any gas/water pipes or electrical cables. Fix the anchors to the ceiling (see Fig.3)
- Add the 4 x brackets to the panel (see Fig. 4) and adjust the length of the steel wires
- Connect the luminaire to the mains supply as detailed above
- Switch on and check for the correct operation
Surface-mounted installation using LPANKIT
- Assemble the surface-mounted frame (LPANKIT, sold separately) with the screws and corner brackets provided (see Fig. 5)
- Using the frame as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any gas/water pipes or electrical cables (see Fig. 6)
- Remove one side of the frame and insert the panel (see Fig. 7)
- Connect the luminaire to the mains supply as detailed above
- Reattach the side of the frame
- Switch on and check for the correct operation
WARNING
This luminaire must be disconnected from the circuit if subjected to any
high voltage or insulation resistance testing. Irreparable damage will occur
if this instruction is not followed.
GENERAL
- This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015.
- This product contains a non-replaceable LED light source and a control gear that can be replaced by a professional.
- Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents that may damage the product.
- This product is dimmable when used with the LPAND dimmable driver, sold separately.
- This product should be dismantled for disposal when it reaches the end of its life. Please see the website for dismantling instructions.
- This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 3 years from the date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free-of-charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice.
INTERNATIONAL CONTACT DETAILS
ML Accessories Limited LU5 4LT www.mlaccessories.co.uk.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>