JBC ALE-908VA Automatic Feed Soldering Station User Manual

: June 13, 2024
: JBC

Table of Contents

ALE-908VA Automatic Feed Soldering Station
Product Information
Product Usage Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ALE-908VA Automatic Feed Soldering Station

Product Information

The ALE Automatic-Feed Soldering Station is a plug-and-play
soldering station that comes in two variations: one with solder
wire perforation and one without. The station is available in
different voltage options (100V, 120V, and 230V) to suit different
electrical systems.

The station with solder wire perforation is available in various
models, including ALE-908VA, ALE-108VA, ALE-208VA, ALE-910VA,
ALE-110VA, ALE-210VA, ALE-912VA, ALE-112VA, ALE-212VA, ALE-915VA,
ALE-115VA, and ALE-215VA. It includes a control unit with the
reference number ALE-908UVA, ALE-108UVA, ALE-208UVA, ALE-910UVA,
ALE-110UVA, ALE-210UVA, ALE-912UVA, ALE-112UVA, ALE-212UVA,
ALE-915UVA, ALE-115UVA, or ALE-215UVA.

The station without solder wire perforation is available in
various models, including ALE-904A, ALE-104A, ALE-204A, ALE-910A,
ALE-110A, ALE-210A, ALE-905A, ALE-105A, ALE-205A, ALE-912A,
ALE-112A, ALE-212A, ALE-906A, ALE-106A, ALE-206A, ALE-915A,
ALE-115A, ALE-215A, ALE-907A, ALE-107A, ALE-207A, ALE-916A,
ALE-116A, ALE-216A, ALE-908A, ALE-108A, ALE-208A, and ALE-918A. It
includes a control unit with the reference number ALE-904UA,
ALE-104UA, ALE-204UA, ALE-905UA, ALE-105UA, or ALE-205UA.

Both variations of the station come with an automatic-feed
soldering iron with the reference number ALE250-A. The station with
solder wire perforation also includes a solder wire guide kit for
ALE250 with perforation, while the station without solder wire
perforation is suitable for solder wires listed as ALE-905UA,
ALE-105UA, and ALE-205UA.

Product Usage Instructions

Choose the appropriate model of the ALE Automatic-Feed
Soldering Station based on your voltage requirements and whether
you need solder wire perforation or not.
If you have purchased the station with solder wire perforation,
ensure that the solder wire guide kit for ALE250 is included inside
the control unit package. The guide wheels should already be
installed in the control unit.
If you require additional solder wire guide kits for different
solder wire diameters, they can be purchased separately from
www.jbctools.com/solder-wire-guide-product-2098.html.
Unpack the purchased station and ensure that all the items
listed in the packing list are included.
If applicable, assemble the ALES Stand for the ALE250
Automatic-Feed Soldering Iron using the provided instructions.
Connect the ALE Automatic-Feed Soldering Station to a power
source that matches the voltage rating of your purchased
model.
Refer to the user manual for detailed instructions on operating
the ALE Automatic-Feed Soldering Station and using the
automatic-feed soldering iron.

ALE
Automatic-Feed Soldering Station
This Plug & Play Guide corresponds to the following references:

1
Station with Solder Wire Perforation
Ref.
ALE-908VA (100 V) ALE-108VA (120 V) ALE-208VA (230 V)
ALE-910VA (100 V) ALE-110VA (120 V) ALE-210VA (230 V)
ALE-912VA (100 V) ALE-112VA (120 V) ALE-212VA (230 V)
ALE-915VA (100 V) ALE-115VA (120V) ALE-215VA (230 V)
ALE-916VA (100 V) ALE-116VA (120 V) ALE-216VA (230 V)

2

Station without Solder Wire Perforation

Ref.
ALE-904A (100 V) ALE-104A (120 V) ALE-204A (230 V)

Ref.
ALE-910A (100 V) ALE-110A (120 V) ALE-210A (230 V)

ALE-905A (100 V) ALE-105A (120 V) ALE-205A (230 V)

ALE-912A (100 V) ALE-112A (120 V) ALE-212A (230 V)

ALE-906A (100 V) ALE-106A (120 V) ALE-206A (230 V)

ALE-915A (100 V) ALE-115A (120 V) ALE-215A (230 V)

ALE-907A (100 V) ALE-107A (120 V) ALE-207A (230 V)

ALE-916A (100 V) ALE-116A (120 V) ALE-216A (230 V)

ALE-908A (100 V) ALE-108A (120 V) ALE-208A (230 V)

ALE-918A (100 V) ALE-118A (120 V) ALE-218A (230 V)

Station
Take a look at the product
web page

Video Guide
Watch the product assembly
video.

1 With Solder Wire Perforation Packing List:

Purchased Station Ref.
ALE-908VA (100 V) ALE-108VA (120 V) ALE-208VA (230 V)
ALE-910VA (100 V) ALE-110VA (120 V) ALE-210VA (230 V)
ALE-912VA (100 V) ALE-112VA (120 V) ALE-212VA (230 V)
ALE-915VA (100 V) ALE-115VA (120V) ALE-215VA (230 V)
ALE-916VA (100 V) ALE-116VA (120 V) ALE-216VA (230 V)

Content*

Control Unit Ref.
ALE-908UVA (100 V) ALE-108UVA (120 V) ALE-208UVA (230 V)
ALE-910UVA (100 V) ALE-110UVA (120 V) ALE-210UVA (230 V)
ALE-912UVA (100 V) ALE-112UVA (120 V) ALE-212UVA (230 V)
ALE-915UVA (100 V) ALE-115UVA (120V) ALE-215UVA (230 V)
ALE-916UVA (100 V) ALE-116UVA (120 V) ALE-216UVA (230 V)
One of the listed control unit references is included according
to the purchased station reference.

Suitable for Solder Wire: Ø 0.8 mm / Ø 0.032 in
Ø 1.0 mm / Ø 0.040 in
Ø 1.2 mm / Ø 0.047 in
Ø 1.5 mm / Ø 0.060 in
Ø 1.6 mm / Ø 0.063 in

Note: A solder wire guide kit is included inside the control unit package and the guide wheels are already installed in the control unit. Other soler wire guide kits for other solder wire diameters are available at www.jbctools.com/ solder-wire-guide-product-2098.html
GALExxV Solder Wire Guide Kit for ALE250
with perforation
GALExxD Solder Wire Guide Kit for ALE250

The following items are included in all purchased station references (1 unit of each item):

C250403

XXXXXX

ALE250 Automatic-Feed Soldering Iron Ref. ALE250-A
2

ALES Stand for ALE250 Automatic-Feed Soldering Iron
Ref. ALE-SA

C250403 Conical Bent Cartridge Ø 1 Ref. C250403

2 Without Solder Wire Perforation Packing List

Station Ref.
ALE-904A (100 V) ALE-104A (120 V) ALE-204A (230 V)
ALE-905A (100 V) ALE-105A (120 V) ALE-205A (230 V)
ALE-906A (100 V) ALE-106A (120 V) ALE-206A (230 V)
ALE-907A (100 V) ALE-107A (120V) ALE-207A (230 V)
ALE-908A (100 V) ALE-108A (120 V) ALE-208A (230 V)
ALE-910A (100 V) ALE-110A (120 V) ALE-210A (230 V)
ALE-912A (100 V) ALE-112A (120 V) ALE-212VA (230 V)
ALE-915A (100 V) ALE-115A (120 V) ALE-215A (230 V)
ALE-916A (100 V) ALE-116A (120 V) ALE-216A (230 V)
ALE-918A (100 V) ALE-118A (120 V) ALE-218A (230 V)

Content*

Control Unit * Ref.
ALE-904UA (100 V) ALE-104UA (120 V) ALE-204UA (230 V)

Suitable for Solder Wire:
wire Ø 0.38 – 0.4 mm / 0.015 – 0.016 in

ALE-905UA (100 V) ALE-105UA (120 V) ALE-205UA (230 V)

wire Ø 0.45 – 0.56 mm / 0.018 – 0.022 in

ALE-906UA (100 V) ALE-106UA (120 V) ALE-206UA (230 V)

wire Ø 0.6 – 0.64 mm / 0.023 – 0.025 in

ALE-907UA (100 V) ALE-107UA (120V) ALE-207UA (230 V)

wire Ø 0.7 – 0.78 mm / 0.028 – 0.031 in

ALE-908UA (100 V) ALE-108UA (120 V) ALE-208UA (230 V)

wire Ø 0.8 – 0.82 mm / 0.032 – 0.033 in

ALE-910UA (100 V) ALE-110UA (120 V) ALE-210UA (230 V)

wire Ø 0.9 – 1.1 mm / 0.036 – 0.044 in

ALE-912UA (100 V) ALE-112UA (120 V) ALE-212UA (230 V)

wire Ø 1.14 – 1.27 mm / 0.045 – 0.051 in

ALE-915UA (100 V) ALE-115UA (120 V) ALE-215UA (230 V)

wire Ø 1.5 – 1.57 mm / 0.06 – 0.063 in

ALE-916UA (100 V) ALE-116UA (120 V) ALE-216UA (230 V)

wire Ø 1.6 – 1.63 mm / 0.063 – 0.065 in

ALE-918UA (100 V) ALE-118UA (120 V) ALE-218UA (230 V)
*One of the listed control unit references is included according to the purchased station
reference.

wire Ø 1.8 mm / 0.073 in

The following items are included in all purchased station references (1 unit of each item):

P405 Pedal Ref. P-405

SCH Catridge Holder Ref. SCH-A

PLR195 Cartridge Extractor Plier Ref. PLR195
3

Axis 2
Reel Locking 3
Solder Reel

Tool Stand

Solder Wire

Watch the product assembly video

Reel Locking Screw
1

Solder Wire Guidance

Solder Reel Wheels (inside) Soldering Iron

Solder Wire Guidance

Step 1 Solder Reel Assembly
Loosen the reel locking screw (1) and remove the reel locking from the axis (2). Assemble the solder reel onto the axis (3). Assemble the solder reel in such a way – when viewed from above that the solder wire unwinds on the dispensing mechanism side (4). Then pass the solder wire through the wire guidance (5).

Allen Key Ø 2,5

Allen Key Ø 1,5

Installation
Before you can start working, the solder reel must be attached and the tool stand, the soldering iron and the power cord connected to the control unit. Follow the assembly steps in this P&P Guide. Note: The solder diameter must match the ALE model purchased. Make sure the solder wire diameter is compatible with the wheels already installed in the ALE control unit.
Solder reel is not included.
Tools Needed
The required tools are located on the control unit.

Staon sengs Feeder sengs Tool sengs Counters Reset

Connuous Supplied: 12 mm

Mode

Program

Edit program

Set default programs

Feeder parameters lock

Off

Programs loaded Tin reload process

Connuous

Wire diameter

Backward

Supplied: 12 mm

Back

Mode Speed Feeder parameters lock Tin reload process

Connuous 5.0mm/s Off

Wire diameter Backward

ConnuouNs one

Back Supplied: 12 mm

Mode Speed Feeder parameters lock Tin reload process

Connuous 5.0mm/s Off

Wire diameter Backward

ConnuouNs one

Back Supplied: 12 mm

Edit program

Speed

Connuous Supplied: 12 mm

Tin reload process Place the n on the gears and press:
Forward BackCwonardnuous
Supplied: 12 mm Press ok to exit

Edit program

Speed

Connuous Supplied: 12 mm

Mode Connuous Disconnuous Program
Back Connuous
Supplied: 12 mm

Staon sengs Feeder sengs Tool sengs Counters Reset

Connuous Supplied: 12 mm

Connuous Supplied: 0 mm

English Deutsch Español
Français Italiano
Português P

Connuous Supplied: 12 mm

Disconnuous mm/s

Program version

Maximum temp

Minimum temp

Off

Sound

Temp units

Connuous

Length units

Staon reset

Supplied: 12 mm

Back

4 Solder Wire Unwinding Direction

Mode

Disconnuous

Speed

20.0mm/s

Length

Feeder parameters lock

Off

Tin reload process Wire diameter

Connuous

Backward

BackSupplied: 12 mm

5

Updang
Your staons is being updated Connuous
Supplied: 12 mm

Do you want to update firmware?

Solder Wire

Spanner

4

Updang
Step 2 Reel Locking Assembly Your staons is being updated Connuous To assSeupmplbielde: 1t2hmemreel locking, its conical side must be pointing downwards (1). Reel Locking Do you want to update firmware?
Reel Locking

1
Conical Side

Align the flat side of the axis (2) with the inner flat side of the reel locking (3). Make sure that the reel locking screw is slightly backed out and does not collide with the axis. Reassemble the reel locking to the axis (4).
Note: To prevent the solder reel from spinning freely or binding, gently press the reel locking down, but only enough to allow the solder reel to rotate freely, before tightening the reel locking screw (5).

Flat Side of the

Reel Locking

4

3

5

Reel Locking

Screw

Flat Side 2 of the Axis

Reel Locking Top View

Flat Side (Reel Locking)
3

Step 3 Cartridge Assembly
For a safe cartridge assembly/change, make sure that the tool is unplugged and the cartridge has cooled down.
Loosen the cartridge set screw (1) and insert the cartidge up to its mark (2). Important: It is essential to insert the cartridge completely for a good connection.
Adjust the tip direction (3) and tighten the cartridge set screw (1).

Cartridge Set Screw

1

Mark

3
2

5

Step 4 Guide Tube Set Assembly

Open the guide tube set screw (1) and insert the guide tube set.

Adjust the guide tube length (2). Leave a gap of 5 to 7 mm (0.197 to 0.276 in) between the tip and the outlet nozzle (3).

If necessary adjust the cartridge tip direction (4) to match the point where the wire will come out. To do this, open the cartridge set screw and tighten it when it is done (5).

Once the guide tube set position is adjusted tighten the guide tube set screw (1).

For a better handling use the clips (6) to band

meters lock

Connuous the guide tubTinerealonaddprotcheses tool cable together.

5.0mm/s Off

Place the n on the gears and press:

ocess er

ConnuouNs one

Forward BackCwonardnuous

Back Supplied: 12 mm

Supplied: 12 mm Press ok to exit

Cartridge Set 5 Screw

4

1

2 5-7 mm 0.197-0.276 in 3

Guide Tube Set Screw

Mode Connuous Disconnuous Program
Back Connuous
Supplied: 12 mm

Connuous Supplied: 0 mm

Guide Tube Set

6 Clips

Disconnuous mm/s

Edit program

Speed Step 5 Tool AsseSpmeed bly

Staon sengs Feeder sengs

Connuous Supplied: 12 mm

Tool sengs

Connect the tool to the conCotnronul ouusnit following thesCoeunters

steps:

Supplied: 12 mm

Reset

Loosen the set screw (1), insert and push the guide nozzle until it stops (2) and tighten the set screw (1).

Connuous Supplied: 12 mm

Then plug in the tool connector (3).

English Deutsch Español
Français Italiano
Português P

Program version

Maximum temp

Minimum temp

Off
ALESo2un5d0

Connuous Automatic-FeeTdemSp uoniltds ering IroConnnuous Length units

Supplied: 12 mm

Staon reset

Supplied: 12 mm

Back

1
Guide Nozzle
2

Tool Connector 3

6

Step 6 Stand, Pedal and Power Cord Installation
At the rear side of the control unit plug in the stand cable, the pedal cable and power cord.

P405 Pedal

ALE Automatic-Feed Control Unit

Power Cord included in JTSE Control Unit

ALES Stand for ALE250 Automatic-Feed
Soldering Iron

Step 7 Station Set Up
Hold up the tool or leave it in the tool holder and switch the station on.

Tin reload process Feeder sengs Tool sengs Staon sengs Counters
Be carefull, cartrige tip will get very hot.

Mode Speed Feeder parameters lock Tin reload process Backward Wire clogging detecon
Back

Connuous None

Important:

Mode

Program

For correct operation, the diameter of the choosen solder wire must match thatEodfittphroegrgamuide kit and its components

(wheels, clamps and nozzles) assembled to the ALE. Guide kits for different wiSreet ddefiaaumlt perotegrrasmsare available at www.

jbctools.com/solder-wire-guide-kit-product-2098.html

Feeder parameters lock

Programs loaded

Edit program

Speed

Change the wire diameter by accessing to main menu pressing value to the current solder wire diameter.

Backward

None

, select “FeWeirde celorgSginegtdteintegcso”n(1) and then “Wire Diameter” (2) to adjust the

Back

Tin reload process

1

Feeder sengs

Tool sengs

Staon sengs

Counters

Language

Reset

Mode

Connuous

Speed

5.0mm/s

Feeder parameters lock

Off

2

Wire diameter

1.00mm

Backward Wire clogging detecon

None On

Back

Disconnuous

Temp adjust

Tot

Temp level set

Off

Plug hrs

7

Sleep delay

Working hrs

Updang

parameters lock

Sleep temp Hibernaon delay

Sleep hrs Hiber hrs

Your staons is being updated Connuous

DisconnTuoooul ssengs

Connuous

Counters

Connuous

m

mm/s

Reset

Supplied: 12 mm

Italiano
Português P

Backward Connuous
Supplied: 12 mm

ConSnouuonuds Temp units
BackSupplieLde:n1g2thmumnits Staon reset

Backward Connuous
Supplied: 12 mm Back

ConTninuroeulosad process

Back

Wire diameter

Connuous

SupplieBda:c1k2wmarmd

BackSupplied: 12 mm

Program version

Mode

Disconnuous

Temp adjust

Part

Tot

Maximum temp

Speed

20.0mm/s

Temp level set

Off

Plug hrs

Step 8 Solder Wire Loading Minimum temp Off

Length

Feeder parameters lock

Off

Sound

Tin reload process

Sleep delay Sleep temp Hibernaon delay

Wheels

Working hrs
Sleep hrs Solder Wire Hiber hrs Guidance

m

TLSeetamngpotMdhnunuareaintsnistekstcees(u1r)S.eupCIpotnlnihetdnar:uo1to2udtmshumecesothldeersowldireerpWBwaaicrkeiswrdseaiaredmiesntetrtohBratcohkSueupgCpoihlninednlt:euh1ot2uemsnmsoozlzdleer

Peripher.
wire gui(2) until it

Connuous Back
Supplied: 12 mm

No tools hrs Sleep cyc Fed cyc

Connuous Supplied: 12 mm

Back
reaches the wheels (3).

Fed mm
3

2

Inlet

1

Nozzle

Select “Tin Reloaded Process” (1) and then press and hold

to

feed the solder wire and advance until it comes out through the

outlet nozzle.

If needed, carefully push the wire until it gets locked in between the

rotating wheels for the wire to start moving forward.

Keep

pressed and after a while the wire will advance faster.

1

Tin reload process

Feeder sengs

Tool sengs

Staon sengs

Counters

Language

Reset

Hibernao Peripher.
Mod Spe Fee Tin Bac Wir

Make sure the wire passes through the intermediate nozzle (4) and enters the guide tube (5).

Solder Wire Outlet

Mode

Program

Edit

Edit program

Set default programs Feeder parameters lock

Solder Wire Inlet

Programs loaded

5 Guide

BackwInartedrm4ediate

Tube Wire clogNgoinzgzldeetecon

Back

SolderNone Wire

Solder Wire Feeding

Mode Speed Feeder parameters lock

Forward the solder wire by pushing the dragging button (1) until the wire comes out of the tip (2).

Backward

Solder Wire Dragging Button

Wire clogging detecon

1

Back

Connuous Off
None

2

Alternatively solder wire can also be fed using the pedal P405. The pedal should be plugged in at theUrepadr aoftnhegfeeder control unit into the

pedal connector.

Your staons is being updated
Connuous

Supplied: 12 mm

8

Do you want to update firmware?

Speed Connuous Supplied: 12 mm

Feeder sengs Tool sengs Counters Reset

Connuous Supplied: 12 mm

Español Français Italiano
Português P

Connuous Supplied: 12 mm

Minimum temp

Off

Sound

Temp units

Connuous

Length units

Staon reset

Supplied: 12 mm Back

Length

Feeder parameters lock

Off

Tin reload process Wire diameter

Connuous

Backward

BackSupplied: 12 mm

Sleep delay Sleep temp Hibernaon delay Peripher.
Bac

Step 9 Solder Wire Unloading

With Solder Wire Perforation
To unload perforated solder wire that has already passed through the guide tube, cut the wire between the wire guidance and the inlet nozzle (1).

Wire Guidance

To extract the wire out of the tool and the guide tube, hold the tool

on your hand and press

until the wire stops mov Mode ing forward. Connuous

Staon sengs

Speed

5.0mm/s

Feeder sengs

Feeder parameters lock

Off

Tin reload process

Tool sengs

Wire diameter

Grasp

the

wire

coming

out

of

the outlet nozzle Counters

Connuous

with

a pliers and Backward

ConnuouNs one

pull

Reset

Supplied: 12 mm

Back Supplied: 12 mm

from it until it is completely out.

Tin reload process Place the n on the gears and press:
Forward BackCwonardnuous
Supplied: 12 mm Press ok to exit

Mode Connuous Disconnuous
InletProNgramozzle Back Connuous
Supplied: 12 mm

1
Connuous Supplied: 0 mm

Disconnuous mm/s

Mode

Program

Edit program

Set default programs

Feeder parameters lock

Off

Programs loaded Tin reload process

Connuous

Wire diameter

Backward

Supplied: 12 mm

Back

Edit program

Speed

Connuous Supplied: 12 mm

Edit program

Speed

Connuous Supplied: 12 mm

Staon sengs Feeder sengs Tool sengs Counters Reset

Connuous Supplied: 12 mm

Without

Solder

Wire

Per

foration Mode Speed

Connuous 5.0mm/s

Feeder parameters lock

Off

Tin reload process

Wire diameter

When

using

a

kit

without

solder Backward

wire perforation, ConnuouNs one
Back

press

Supplied: 12 mm

until the wire is completely wound to unload the solder wire.

It is best to rotate the reel by hand as the wire is being pulled back

in order to keep it neatly arrangedUpdoanng the reel. Your staons is being updated Connuous

Supplied: 12 mm
Or, if prefered, proceed as described above for perforated solder

wire unloading.

Do you want to update firmware?

Solder Reel

English Deutsch Español
Français Italiano
Português P

Connuous Supplied: 12 mm

Program version

Maximum temp

Minimum temp

Off

Sound

Temp units

Connuous

Length units

Staon reset

Supplied: 12 mm Back

Wire Winding Direction

Mode

Discon

Speed

20.0

Length

Feeder parameters lock

Tin reload process Wire diameter

Connuou

Backward

BackSupplied: 12

Solder Wire

Step 9 Control Process
Feeder Setting Modes Depending on the selected mode, different parameters are available for “Feeder Settings”. Choose between “continuous”, “discontinuous” and “program” mode. Access to Main Menu by pressing , select “Feeder Settings” (1) and then “Mode” (2). For mor details see ALE control Unit Manual or JBC Web www.jbctools.com/auto-feed-stations.html

Mode Speed Feeder parameters lock Tin reload process Backward Wire clogging detecon
Back

ConnuMouosde Speed Feeder parameters lock TWinirreedloiaamd eptreorcess
NoBnacekward Wire clogging detecon

TiCnornelonaudopursocess

5.0Pmlamce/sthe n on the gears On and press:

1.00mm None On

Forward Backward

Back Press ok to exit

Tin reload process

Mode

Place the n on the geCaornsnuous and press: Disconnuous

ForwardProgram

Backward

Back

Press ok to exit

Mode Connuous Disconnuous Program
Back

EdPitropgrroagmram None

Edit program

For more details see ALE control unit instruction manual,

Speed download at www.jbSpcetoedols.com/ale-produSpcet-e2d037.html

Tin reload process FeedeAcrocsencternsogsl sutonitALE ToolSspepereodndgus ct page
Staon sengs
Counters

Tin reload process Feeder sengs Tool sengs Staon sengs Counters

English Deutsch Español
9 Italiano
Português

Notes
10

Notes
11

Specifications
ALE Automatic-Feed Soldering Station
With Solder Wire Perforation
for wire Ø 0.8 mm / Ø 0.032 in
ALE-908VA (100 V) ALE-108VA (120 V) ALE-208VA (230 V)
for wire Ø 1.0 mm / Ø 0.040 in
ALE-910VA (100 V) ALE-110VA (120 V) ALE-210VA (230 V)
for wire Ø 1.2 mm / Ø 0.047 in
ALE-912VA (100 V) ALE-112VA (120 V) ALE-212VA (230 V)
for wire Ø 1.5 mm / Ø 0.060 in
ALE-915VA (100 V) ALE-115VA (120V) ALE-215VA (230 V)
for wire Ø 1.6 mm / Ø 0.063 in
ALE-916VA (100 V) ALE-116VA (120 V) ALE-216VA (230 V)
For all ALE Stations: – Package Dimensions / Weight: (L x W x H)
Complies with CE standards. ESD safe.

Without Solder Wire Perforation
for wire Ø 0.38 – 0.4 mm / Ø 0.015 – 0.016 in
ALE-904A (100 V) ALE-104A (120 V) ALE-204A (230 V)
for wire Ø 0.46- 0.56 mm / Ø 0.018 – 0.022 in
ALE-905A (100 V) ALE-105A (120 V) ALE-205A (230 V)
for wire Ø 0.6 – 0.64 mm / Ø 0.023 – 0.025 in
ALE-906A (100 V) ALE-106A (120 V) ALE-206A (230 V)
for wire Ø 0.7 – 0.78 mm / Ø 0.028 – 0.031 in
ALE-907A (100 V) ALE-107A (120 V) ALE-207A (230 V)
for wire Ø 0.80 – 0.82 mm / Ø 0.032 – 0.033 in
ALE-908A (100 V) ALE-108A (120 V) ALE-208A (230 V)
545 x 345 x 275 mm / 6.72 Kg 21.46 x 13.58 x 10.83 in / 14,82 lb

for wire Ø 0.90 – 1.10 mm / Ø 0.036 – 0.044 in
ALE-910A (100 V) ALE-110A (120 V) ALE-210A (230 V)
for wire Ø 1.14 – 1.27 mm / Ø 0.045 – 0.051 in
ALE-912A (100 V) ALE-112A (120 V) ALE-212A (230 V)
for wire Ø 1.5 – 1.57 mm / Ø 0.06 – 0.062 in
ALE-915A (100 V) ALE-115A (120 V) ALE-215A (230 V)
for wire Ø 1.6 – 1.63 mm / Ø 0.063 – 0.065 in
ALE-916A (100 V) ALE-116A (120 V) ALE-216A (230 V)
for wire Ø 1.8 mm / Ø 0.073 in
ALE-918A (100 V) ALE-118A (120 V) ALE-218A (230 V)

Warranty
Get 2 year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.
This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

0030444 -040523