HARBOR FREIGHT 58800 Heavy Duty U Joint Puller Class 6 7 and 8 Trucks Instructions

HARBOR FREIGHT 58800 Heavy Duty U Joint Puller Class 6 7 and 8 Trucks

Product Information

• Product Name: Heavy Duty U-Joint Puller
• Product Type: Tool
• Compatible Vehicles: Class 6, 7 & 8 Trucks
• Model Number: 58800
• Manufacturer: Harbor Freight
• Website: http://www.harborfreight.com
• Email Technical Support: productsupport@harborfreight.com

Product Usage Instructions

1. Ensure that the product is intact and undamaged when unpacking. If any parts are missing or broken, contact customer support at 1-888-866-5797.
2. Gather the necessary tools required for assembly and service. Note that these tools may not be included with the product.
3. Read the entire owner’s manual and safety instructions before using the product. Failure to do so may result in serious injury.
4. Keep children and bystanders away from the product while operating to avoid distractions and potential accidents.
5. Maintain a clean and well-lit work area to minimize accidents caused by clutter or inadequate lighting.
6. Wear ANSI-approved safety goggles, NIOSH-approved dust mask/respirator, and heavy-duty work gloves during use and service.
7. Stay alert and use common sense when operating the product. Avoid using it when tired or under the influence of drugs, alcohol, or medication.
8. Avoid overreaching and maintain proper footing and balance at all times for better control in unexpected situations.
9. Dress properly by avoiding loose clothing, jewelry, and keeping hair, clothing, and gloves away from moving parts to prevent entanglement.
10. Keep the product out of reach of children as it is not a toy.
11. Ensure that the correct product is used for the correct vehicle. Modifying the product or using it for unintended purposes can be unsafe.
12. Regularly check for misalignment, binding of moving parts, breakage, or any other condition that may affect the product’s operation. Have any damages repaired before use.
13. Use the product and its accessories according to the provided instructions and for the intended type of work and working conditions. Using the product for operations different from those intended can be hazardous.
    It is important to follow all safety warnings, instructions, and precautions mentioned in the owner’s manual for safe and proper usage of the Heavy Duty U-Joint Puller.

Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com

INTRODUCTION

• When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2022 by Harbor Freight Tools®. All rights reserved.
• No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

WARNING SYMBOLS AND DEFINITIONS

IMPORTANT SAFETY INFORMATION

WARNING Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.

1. Keep children and bystanders away while operating. Distractions can cause you to lose control.
2. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
3. Wear ANSI-approved safety goggles, NIOSH-approved dust mask/respirator, and heavy-duty work gloves during use and service.
4. Stay alert and use common sense when operating. Do not use when tired or under the influence of drugs, alcohol or medication.
5. Do not overreach. Keep proper footing and balance at all times. This enables better control in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
7. This product is not a toy. Keep it out of reach of children.
8. Use the correct product for the correct vehicle. The correct product will do the job better and safer at the rate for which it was designed. Do not modify this product or use it for a purpose for which it is not intended.
9. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the product’s operation. If damaged, have the product repaired before use.
10. Use the product and accessories etc., in accordance with these instructions and in the manner intended for the particular type of product, taking into account the working conditions and the work to be performed. Use of the product for operations different from those intended could result in a hazardous situation.
11. Have product serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
12. Maintain labels and nameplates on the product. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
13. Use caution when applying a load. Slowly and carefully apply pressure to the vehicle part being pressed. If the workpiece seems unusually hard to press, immediately stop the operation. Carefully disconnect the U-Joint Puller from the workpiece, and adjust the U-Joint Puller to eliminate or diminish an off-center load. Then continue with the procedure.
14. Do not use the U-Joint Puller to compress springs or any other item that could disengage and cause a potential hazard
15. Do not allow any lubricants to make contact between any part of the U-Joint Puller and the part being pressed. Lubricants of any type on the above mentioned parts will diminish the ability of the U-Joint Puller to firmly and safely grip and hold the U-Joint in position.
16. Examine the U-Joint Puller for structural cracks, bends, and any other condition that may affect the safe operation of the tool. Do not use the U-Joint Puller even if minor damage appears.
17. Read and understand all instructions and safety precautions as outlined in the manufacturer’s manual for the vehicle you are servicing.
18. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

Functions

Operating Instructions

Read the ENTIRE WARNING section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Note: Read vehicle service manual to determine how to prepare the ball joint for removal from a specific vehicle make/model. The generic instructions that follow may, or may not apply to your vehicle.
Warning! Follow proper vehicle safety recommendations when lifting vehicle or removing drive shaft from vehicle.

To Remove a U-Joint
CAUTION! Check Forcing Screw to make sure threads are clean of debris and lubricated before usage everytime to prevent damage to the tool.

1. Remove all retainers and fasteners from Bearing Cups.

2. Install the U-Joint Puller over the Yoke and turn the Forcing Screw clockwise using a wrench or socket until the Bearing Cup is loose.

3. Remove the Bearing Cup.

4. Repeat steps 1-3 on each Bearing Cup.

Cleaning, Maintenance, and Lubrication

Do not perform any inspection, maintenance or cleaning procedures when the U-Joint Puller is under a load.

1. BEFORE EACH USE, inspect the general condition of the U-Joint Puller. Check for misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment.
2. PERIODICALLY, use a premium quality and light weight machine oil to lubricate the threads of the Jackscrew.
3. PERIODICALLY, check retaining Screw (5) to make sure it is tight. The screw can loosen from extended use with an impact. Torque to 120 ft lbs.
4. PERIODICALLY, check Washer (4) for any damage or extended wear. Replace as needed.
5. AFTER USE, wipe clean with a damp cloth, using a mild detergent or mild solvent.
6. When storing, keep U-Joint Puller in its Carrying Case.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List & Diagram

Part| Description| Qty|  | Part| Description| Qty
---|---|---|---|---|---|---
1| Screw| 1| 4| Washer| 1
2| Frame| 1| 5| Screw| 1
3| Glove| 1| 6| Dust Cap| 1

Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175446787 when ordering parts

ICON™ TOOL LIMITED LIFETIME WARRANTY

• Harbor Freight Tools makes every effort to assure that its products meet the highest quality and durability standards. Harbor Freight Tools warrants to the original purchaser of this ICON™ Tool that the parts and components of the ICON™ Tool will be free from defects in material and manufacturing workmanship during the ICON™ Tool’s useful life. If the parts or components do not perform in accordance with this warranty, Harbor Freight Tools will provide the parts necessary to put the ICON™ Tool back in working order. Replacement parts may be obtained by calling 1-888-866-5797 or by e-mailing productsupport@harborfreight.com. Proof of purchase (original sales receipt) from the original consumer purchaser must accompany all warranty claims.
• This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, unauthorized repair, improper installation, improper storage, normal wear and tear, neglect, alteration or modification, or to lack of maintenance. This warranty is in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. Harbor Freight Tools is not liable for incidental, indirect, special, consequential, or punitive damages or costs arising from the use of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

ABOUT COMPANY

• 26677 Agoura Road,
• P. O. Box 6009
• Calabasas, CA 91302
• 1-888-866-5797

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>