CROUZET 88983903 Kit Millenium Slim User Guide

88983903 Kit Millenium Slim
User Guide

88983903 Kit Millenium Slim

| Without terminal blocks| With terminal blocks
---|---|---
CB8R 24 VDC
CB8S 24 VDC
CB8R 110-240 VAC| 88 983 001
88 983 002
88 983 003| 88 983 901
88 983 902
88 983 903
Alternate products range

Software minor changes| 88 983 700…799
Cosmetic or minor changes| 88 983 800…899

IMPORTANT: This document provides installation instructions only.
See the software’s help section for its operation and programming.
Those responsible for the application, implementation, or use of this product must ensure that the necessary design considerations have been incorporated into each application,
completely adhering to applicable laws, performance and safety requirements, regulations, codes, and standards.
The customer is responsible for all consequences of the application.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Turn the power off before installing, removing, wiring or maintaining.

Failure to follow this instruction will result in death or serious injury.
WARNING
EXPLOSION HAZARD

• Confirm that the product power supply voltage and its tolerances are compatible with those of the network.
• Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.

UNINTENDED EQUIPMENT OPERATION

• This product is not intended for use in safety-critical machine functions. Where personnel and or equipment hazards exist, use appropriate hard-wired safety interlocks.
• Do not disassemble, repair or modify the controllers.
• This controller is designed for use within an enclosure (closed with a key or a tool) according to specifications described in these instructions in the paragraph on installation conditions.
• Install the controller in the operating environment conditions described below.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

General

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Crouzet for any consequences arising out of the use of this manual.
-For more technical details on the characteristics and intended use of the product, please refer to the datasheet available on the CROUZET website

is marked
| Recyclable materials
| Refer to the product recycling instructions
| This product is not disposable in a conventional trash can. This must be brought to a collection point

-The product should be cleaned with a damp cloth

Description

1. Power supply terminals
2. Input terminals
3. Output terminals
4. Spring for DIN rail| 5. Green LED – Status
6. Blue LED – Bluetooth
7. Mounting holes
8. Bluetooth antenna
---|---

Installation conditions

A switch or circuit-breaker must be included in the installation; it must be suitably located and easily reached;
it must be marked as the disconnecting device for the equipment
DIN rail mounting

Screw mounting

Front panel mounting
Enclosure Type 1 mounting instruction

****Position of the Bluetooth antenna.
Front panel mounting is recommended for communicating outside a metal enclosure

Installation

Inputs and power supplies **

**

AC Inputs

|
---|---

DC Inputs

|
---|---
|
|
|
(1) 1 A (UL248) quick-blowing fuse, circuit-breaker, or circuit protector (US)| Isolating source

Outputs

Relay outputs

|
---|---

Static outputs

|
---|---
(1) 1 A (UL248) quick-blowing fuse, circuit-breaker, or circuit protector (US| (2) Isolating the source

Operation of LEDs

Bluetooth interface

Compatibilities:

• A 88 980 124 dongle facilitates communication with the Bluetooth interface. It is compatible with Windows 7 and the most recent Windows operating systems.

• Frequency bands used by the transmitter/receiver: 2402 – 2480 MHz.
  Maximum radio-frequency power transmitted on the frequency bands used by the transmitter /receiver: + 3dBm

• This device complies with part 15 of the FCC Rules. Operation is subject to the following 2 conditions:

Caution: the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure
This device complies with FCC RF radiation exposure limits set forth for the general population.
This device must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
SIMPLIFIED EU DECLARATION OF CONFORMITY
The simplified EU declaration of conformity referred to in Article 10(9) shall be provided as follows:
Hereby, Crouzet declares that the radio equipment type BLUETOOTH INTERFACE is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://automation.crouzet.com/get- help/techdatabase/
**Operation
Allows wireless communication**

Software Workshop (on PC):

• Read/write the customer application
• Update the firmware
• Debug data
• Read the data logs

Virtual display on PC, tablet, Android, and IOS smartphone:

• Visualization of the front panel of the base Millenium Slim
• Forcing the buttons

Installation
Download installation sheet, datasheet:www.automation.crouzet.com/support
Crouzet Soft workshop’s installation on computer:

1. Download software: www.automation.crouzet.com
   Firmware update or application loading:

2. Power on the logic controller

3. Pair the product with the Bluetooth connection

4. Do the transfer
   

Connection

889830XX: Without terminal blocks
Compatible references of connectors:
Screw version:

• Phoenix Contact MSTBT 2,5/ 6-ST-5,08 (Green – Order N° 1781027)
• Phoenix Contact MSTBT 2,5/ 6-ST-5,08 GY (Grey – Order N° 1147774)
• Phoenix Contact MSTBT 2,5/ 6-ST-5,08 BK (Black – Order N° 1800921)

Push-in spring connection :

• Phoenix Contact FKCN 2,5/6-ST-5,08 (Green – Order N° 1754607)
• Phoenix Contact FKCN 2,5/ 6-ST-5,08 BK (Black – Order N° 1710112)

889839XX: With terminal blocks MSTBT

mm
……
inch

| | | | |
---|---|---|---|---|---
mm2| 0.25….2.5| 0.25….1| 0.5….1.5| 0.2….2.5| 0.21
AWG| 24…12
UL: Cu, 80°C min|
|

03 mm
(0.12 in)

---|---
C| N.m|  0.5
lb-in| 4.5

Contact information
www.automation.crouzet.com/contact
FR – 26000 Valence

All rights of reproduction, modification or reprinting and translation reserved for all countries – © CROUZET

References

• CROUZET products catalog & media files
• Crouzet Automation, Automation for Everyone
• Crouzet Automation, Automation for Everyone
• CROUZET products catalog & media files

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>