R V R TX03KSS TX-KSS Plug In Series FM Stations Owner’s Manual
- June 13, 2024
- R V R
Table of Contents
TX03KSS TX-KSS Plug In Series FM Stations
Owner’s Manual
TX03KSS TX-KSS Plug In Series FM Stations
TX-KSS PLUG-IN
MID/HIGH POWER HOT PLUG
from 3000W to 60.000W
Developed for the most demanding FM Radio Networks, this line of products has
been conceived for all stations that needs to ensure broadcast continuity and
simplify any maintenance operation. All hot pluggable transmitters exceed
ETSI/CCIR/FCC standards on RF harmonics and spurious, performing high
efficiency and ensuring the clients in investing in product with a high life
span.
MODELS
| TX03KSS | TX04KSS | TX05KSS |
|---|---|---|
| TX06KSS | TX08KSS | TX10KSS |
| TX12.5KSS | TX20KSS | TX25KSS |
| TX32KSS | TX40KSS | TX50KSS |
| TX60KSS |
FM STATIONS
- The most reliable FM broadcasting solution on the market designed for 24/7 nonstop operation.
- Capable of Analog and Digital transmission depending on the configuration.
- Reduced failure rate thanks to hot plug-in connectors replacing most of the classical wiring.
- Over-dimensioned amplifiers modules.
- In case of fail, the total power output will not go below -3dB.
- Independent and hot-swap amplifier’s modules.
- Intelligent stand alone hot-swap fan arrays.
- Overall efficiency up to 76% depending on the configuration.
- N+1 Configuration available for 24/7 business continuity.
- Built-in exciter’s automatic or manual changeover.
- Simplified maintenance: common spare parts on the entire series from 3.000W to 60.000W.
- Tunable over the entire FM band 87.5 – 108 MHz, without tuning. Other bands on equest.
- Remote controls: WEB, SNMP2, GSM, Serial and Complete FM monitoring (option).
- Exceeds ETSI/CCIR/FCC requirements regarding RF harmonics and RF spurious.
- Single phase or three phase power configuration.
Exciters:
- TEX, PTX Series depending on client’s requirements and budget. Single and
- Dual Drive with automatic or manual changeover.
- Programmable Timing & Priority of all audio inputs depending on configuration.
- Fold-back control for effective “VSRW” protection.
- Including IAMLC: Intelligent Automatic Modulation Level Control.
- Low distortion and intermodulation values.
Amplifiers:
- Hot Plug-in modules available in 2.300W or 2.500W depending on system’s configuration.
- Independent power supply per each amplifier’s module.
- Independent fan array per each amplifier’s module.
- Automatic Power Control.
- Advanced protections against high VSWR, overdrive, overcurrent and overtemperature.
- Ease of maintenance.
ORDERING INFORMATION
| Model | Description |
|---|---|
| TX03KSS | Plug-in transmitter, 3kW (composed of PJ3KPS-CA + 2x PTX30DDS). |
| TX04KSS/60D44 | Plug-in transmitter, 4kW (composed of PJ4KPS-CA + 2x PTX30DDS). |
| TX05KSS | Plug-in transmitter, 5kW (composed of PJ5KPS-CA + 2x PTX30DDS). |
| TX06KSS/60D42 | Plug-in transmitter, 6kW (composed of PJ6KPS-CA + 2x PTX30DDS). |
| TX08KSS/60D43 | Plug-in transmitter, 8kW (composed of PJ8KPS-CA + 2x PTX30DDS). |
| TX10KSS/60D41 | Plug-in transmitter, 10kW (composed of PJ10KPS-CA + 2x |
PTX30DDS).
TX12.5KSS/60D41| Plug-in transmitter, 12.5kW (composed of PJ12.5KPS-CA + 2x
PTX30DDS).
TX20KSS/61D412| Plug-in transmitter, 20kW (composed of 2x PJ10KPS-CA + 2x
PTX100DDS).
TX25KSS/60D451| Plug-in transmitter, 25kW (composed of PJ20KPS-CA + 2x
PTX30DDS).
TX32KSS/60D472| Plug-in transmitter, 32kW (composed of 2x PJ16KPS-CA + 2x
PTX30DDS).
TX40KSS/61D414| Plug-in transmitter, 40kW (composed of 4x PJ10KPS-CA + 2x
PTX30DDS).
TX50KSS| Plug-in transmitter, 50kW (composed of 5x PJ10KPS-CA + 2x PTX30DDS).
TX60KSS| Plug-in transmitter, 60kW (composed of 6x PJ10KPS-CA + 2x PTX30DDS).
TX10KSS/60D41
Plug-in transmitter, 10kW (composed of PJ10KPS-CA + 2x PTX30DDS).
TX20KSS/61D412
Plug-in transmitter, 20kW (composed of PJ20KPS-CA + 2x PTX30DDS).
TX60KSS
Plug-in transmitter, 60kW (composed of PJ60KPS-CA+ 2x PTX30DDS).
TX10KSS/60D41
Parameters U.M.
Value| Notes
---|---
GENERALS
RF Output Power| kW| 10,5|
Frequency Range| MHz| 87,5 – 108|
Frequency Stability| ppm| > 1|
Frequency programmability| | By software, with 1, 10, 100 , 1000 kHz
steps|
Nominal Frequency Deviation| | ±75 KHz (peak)|
Maximum Frequency Deviation| | ±150 KHz (peak)|
Class of Emission| | 180KF8E Direct to Channel|
Modulation Mode| | Mono, Stereo, Multiplex, SCA, RDS, Aux|
Stereo transmissions| | Acc. to ITU-R / Rec. 450 (Pilot tone)|
RF Output Impedance| | 50 Ω, Unbalanced|
RF Output Connector| | 1-5/8” EIA Flange|
VSWR| | 1.4:1 with automatic fold-back at higher VSWR|
Pre-emphasis Mode| | 0/50 (CCIR) µs,75 (FCC) μs|
Asynchronous AM S/N Ratio| | Typically >70dB|
Synchronous AM S/N Ratio| | Typically > 55dB|
Harmonics suppression and Spurious| | Typically <85db|
Overall efficiency| | Typically > 70%|
RF Harmonics| | Exceeds ETSI/CCIR/FCC requirements|
RF Spurious| | Exceeds ETSI/CCIR/FCC requirements|
Analogue Input level {+75 Khz (peak) deviation
}| | -12,5 dBu – +12,5 dBu (adjustable)|
Digital Input level {+75 Khz (peak) deviation
}| | -20,0 dBFS – 0 dBFS (adjustable)|
MONO OPERATION
S/N ratio| dB| Typically > 83|
Total Harmonic Distortion + Noise| %| Typically <0,03|
Inter Modulation Distortion SMPTE| %| Typically <0,02|
Frequency Response| dB| Typically ±0,2|
Audio Input Impedance| | 600 Ω or 10 kΩ|
MPX OPERATION
Composite S/N ratio| dB| Typically > 80|
Total Harmonic Distortion + Noise| %| Typically <0,05|
Inter Modulation Distortion| %| Typically <0,05|
Frequency Response| dB| Typically ±0,2|
Audio Input Impedance| | 10 kΩ|
STEREO OPERATION
Stereo FM S/N Ratio| dB| Typically > 83|
Total Harmonic Distortion + Noise (L or R)|
%| Typically <0,02|
Inter Modulation Distortion SMPTE (L or R)| %|
Typically <0,02|
Frequency response (L or R)| dB| Typically ±0,2|
Linear Cross Talk| dB| Typically > 50|
Non-linear Cross Talk| dB| Typically > 50|
Stereo Separation (Sine Wave)| dB| Typically > 70|
Audio Input Impedance| | 600 Ω or 10 kΩ|
Digital Input Impedance| | 110 Ω|
TX20KSS/61D412
| Parameters **** U.M. Value | Notes |
|---|
GENERALS
RF Output Power| kW| 21|
Frequency Range| MHz| 87,5 – 108|
Frequency Stability| ppm| ± 1|
Driver power for rated output| W| 20 – 25|
Nominal Frequency Deviation| | ±75 KHz (peak)|
Maximum Frequency Deviation| | ±150 KHz (peak)|
Class of Emission| | 180KF8E Direct to Channel|
Modulation Mode| | Mono, Stereo, Multiplex|
Stereo transmissions| | Ace to ITU-R / Ree 450 (Pilot tone)|
RF Output Impedance| Ω| 50|
RF Output Connector| | 3-1/8” EIA Flange|
VSWR| | 1.4:1 with automatic fold-back at higher VSWR|
Pre-emphasis Mode| | 0/50 (CCIR) µs,75 (FCC) μs|
Asynchronous AM S/N Ratio| dB| Typically >70|
Synchronous AM S/N Ratio| dB| Typically > 55|
Harmonics suppression and Spurious| dB| Typically <85|
Overall efficiency| %| Typically > 72-74|
RF Harmonics| | Exceeds ETSI/CCIR/FCC requirements|
RF Spurious| | Exceeds ETSI/CCIR/FCC requirements|
Analogue Input level {+75 Khz (peak) deviation
}| | -12,5 dBu – +12,5 dBu (adjustable)|
Digital Input level {+75 Khz (peak) deviation
}| | -20,0 dBFS – 0 dBFS (adjustable)|
POWER REQUIREMENTS
AC power input
| AC supply voltage| | 400V ±10% AC Three-Phase 3F-N 230V ±10% AC Three-Phase
3F-N|
Active power consumption| | From 29,1 kW to 28,3 kW|
Overall efficiency| %| Typically > 72-74|
Power factor| dB| > 0,95|
Connector| | Terminal Block Standard|
MECHANICAL DIMENSIONS
Phisical dimensions mm (WxHxD)| | 1370 x 1910 x 1150|
Cooling| | Forced, with internal fan|
Acoustic Noise| dba| <75|
Weight| Kg| About 770|
MONO OPERATION
S/N ratio| dB| Typically > 83|
Total Harmonic Distortion + Noise| %| Typically <0,03|
Inter Modulation Distortion SMPTE| %| Typically <0,02|
Frequency Response| dB| Typically ±0,2|
Audio Input Impedance| | 600 Ω or 10 kΩ|
MPX OPERATION
Composite S/N ratio| dB| Typically > 80|
Total Harmonic Distortion + Noise| %| Typically <0,05|
Inter Modulation Distortion| %| Typically <0,05|
Frequency Response| dB| Typically ±0,2|
Audio Input Impedance| kΩ| 10|
STEREO OPERATION
Stereo FM S/N Ratio| dB| Typically > 83|
Total Harmonic Distortion + Noise (L or R)|
%| Typically <0,02|
Inter Modulation Distortion SMPTE (L or R)| %|
Typically <0,02|
Frequency response (L or R)| dB| Typically ±0,2|
Linear Cross Talk| dB| Typically > 50|
Non-linear Cross Talk| dB| Typically > 50|
Stereo Separation (Sine Wave)| dB| Typically > 70|
Audio Input Impedance| | 600 Ω or 10 kΩ|
Digital Input Impedance| Ω| 110|
TX60KSS
| Parameters **** U.M. Value | Notes |
|---|
GENERALS
RF Output Power| kW| 65|
Frequency Range| MHz| 87,5 – 108|
Frequency Stability| ppm| ± 1|
Driver power for rated output| W| 100|
Nominal Frequency Deviation| | ±75 KHz (peak)|
Maximum Frequency Deviation| | ±150 KHz (peak)|
Class of Emission| | 180KF8E Direct to Channel|
Modulation Mode| | Mono, Stereo, Multiplex|
Stereo transmissions| | Ace to ITU-R / Ree 450 (Pilot tone)|
RF Output Impedance| Ω| 50|
RF Output Connector| | 3-1/8” EIA Flange|
VSWR| | 1.4:1 with automatic fold-back at higher VSWR|
Pre-emphasis Mode| | 0/50 (CCIR) µs,75 (FCC) μs|
Asynchronous AM S/N Ratio| dB| Typically >70|
Synchronous AM S/N Ratio| dB| Typically > 55|
Harmonics suppression and Spurious| dB| Typically <85|
Overall efficiency| %| Typically > 72-74|
RF Harmonics| | Exceeds ETSI/CCIR/FCC requirements|
RF Spurious| | Exceeds ETSI/CCIR/FCC requirements|
Analogue Input level {+75 Khz (peak) deviation
}| | -12,5 dBu – +12,5 dBu (adjustable)|
Digital Input level {+75 Khz (peak) deviation
}| | -20,0 dBFS – 0 dBFS (adjustable)|
POWER REQUIREMENTS
AC power input
| AC supply voltage| | 400V ±10% AC Three-Phase 3F-N 230V ±10% AC Three-Phase
3F-N|
Active power consumption| | From 29,1 kW to 28,3 kW From 58,3 kW to 56,7 kW
From 90 kW to 92 kW|
Overall efficiency| %| Typically > 72-74|
Power factor| dB| > 0,95|
Connector| | Terminal Block Standard|
MECHANICAL DIMENSIONS
Phisical dimensions mm (WxHxD)| | 3425 x 1910 x 1150|
Cooling| | Forced, with internal fan|
Acoustic Noise| dba| <75|
Weight| Kg| About 1150|
MONO OPERATION
S/N ratio| dB| Typically > 83|
Total Harmonic Distortion + Noise| %| Typically <0,03|
Inter Modulation Distortion SMPTE| %| Typically <0,02|
Frequency Response| dB| Typically ±0,2|
Audio Input Impedance| | 600 Ω or 10 kΩ|
MPX OPERATION
Composite S/N ratio| dB| Typically > 80|
Total Harmonic Distortion + Noise| %| Typically <0,05|
Inter Modulation Distortion| %| Typically <0,05|
Frequency Response| dB| Typically ±0,2|
Audio Input Impedance| kΩ| 10|
STEREO OPERATION
Stereo FM S/N Ratio| dB| Typically > 83|
Total Harmonic Distortion + Noise (L or R)|
%| Typically <0,02|
Inter Modulation Distortion SMPTE (L or R)| %|
Typically <0,02|
Frequency response (L or R)| dB| Typically ±0,2|
Linear Cross Talk| dB| Typically > 50|
Non-linear Cross Talk| dB| Typically > 50|
Stereo Separation (Sine Wave)| dB| Typically > 70|
Audio Input Impedance| | 600 Ω or 10 kΩ|
Digital Input Impedance| Ω| 110|
All pictures are RVR’s property and they are only indicative and not binding. The pictures can be modified without notice. These are general specifications. They show typical values and are subject to change without notice.
R.V.R. Elettronica S.r.l.
Via del Fonditore 2/2
40138 Bologna – ltaly
Phone +39 0516010506
sales@rvr.it
www.rvr.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>