MONSTER 2MNTW0395 DNA Go In Ear Bluetooth Earbuds User Manual

: June 13, 2024
: Monster

Table of Contents

MONSTER 2MNTW0395 DNA Go In Ear Bluetooth Earbuds
FCC STATEMENT
Product Specs
Monster DNA GO
Bluetooth® Pairing
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MONSTER 2MNTW0395 DNA Go In Ear Bluetooth Earbuds

FCC STATEMENT

This Bluetooth® earpiece shall be charged by the supplied charging unit only.

Caution: The batteries in this product are not replaceable. During use, storage or transportation the battery should not be subjected to extremely low temperatures or low air pressure at high altitudes. If the battery is exposed to extremely high temperatures it could result in an explosion or the leaking of ﬂammable liquid or gas. Please take care when disposing of the unit; disposal in a ﬁre, oven, mechanically crushing or cutting machine could cause an explosion.

Warning: Do not dispose of the unit in ﬁre or water. Never attempt to disassemble and reassemble. Waste electrical products should not be disposed of with household waste, please recycle where facilities exist. Check with your local authority for recycling advice. Keep your device and all accessories out of the reach of children and animals. Small parts may cause choking or serious injury if swallowed. Avoid exposing your device to very cold or very hot temperatures (Below 0° or above 45° C). Extreme temperatures can cause the deformation of the device and reduce the charging capacity and life of your device. Do not allow your device to get wet, liquids can cause serious damage. Do not handle your device with wet hands. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc., iPhone, iPad, and Mac is a trademark of Apple Inc., registered in the U.S. and other countries. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a wireless power charger, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.

Product Specs

Model No: Monster DNA GO
Version: 5.2 Bluetooth® Chipset
Support proﬁles: HSP/HFP/A2DP/AVRCP Frequency response: 20hz-20kHz
Impedance: 32Ω
Driver size: 12mm
Sensitivity: 110±3dB
Eﬀective range: up to 10 meters
Earbud battery capacity: 2 x 50mAh Playing time: 7-8 hours
Charging case battery capacity: 400mAh Earbud charging time: Max. 1.5 hour Charging case charge time: Approx. 1.5 hours Charging port: Type-C™
Input voltage: DC5.0V / 1A
Ingress protection: iPX5 (Earbuds only) Wireless charging: Yes, QI™ standard

Monster DNA GO

Earbud Operation

Power on
Take both earbuds out of the charging case and they will automatically power ON. Alternatively, if the earbuds are powered oﬀ, press and hold the (MFB) button for 2 seconds.

Power oﬀ:
Place the earbuds back in the charging case, ensure that the case is powered, the earbuds will be automatically powered OFF. Or you can press and hold the (MFB) button on either earphone for 9 seconds.

Play/Pause:
Press either “MFB” button once.

Volume Down:
Press and hold the left “MFB” decrease volume incrementally.

Volume Up:
Press and hold the right “MFB” increase volume incrementally.

Previous Track:
Double press the Left “MFB”.

Next Track:
Double press the Right “MFB”.

Answer Call:
Press either “MFB” button once. (if answering a call while on another call, then the ﬁrst call will be placed on hold).

Reject Call:
Double press either “MFB”.

End Call:
Press either “MFB” button. Activating Phone Assistant: Triple press either “MFB”. (does not work during a call)

Pairing:
When the earbuds are removed from the charging case for the ﬁrst time, they will enter Bluetooth pairing automatically. To pair to a new device, disconnect from the DNA GO or turn oﬀ Bluetooth pairing on your original device.

Bluetooth® Pairing

Go to the “Bluetooth” Setting on your Bluetooth® device (Phone, Tablet, etc.). Turn the Bluetooth® ON, on your device. Open the charging case, and take the earbuds out, they will turn on automatically. If this is your first time using your earbuds, they will automatically enter Bluetooth Pairing mode. On your device’s Bluetooth menu, select the ‘Monster DNA Go’ earbuds from the list of available devices. To pair your earbuds to a different Bluetooth® device, disconnect from the DNA GO or turn off Bluetooth® pairing on your original device. Remove the earbuds from the case and they will enter pairing mode automatically.

Troubleshoot tip: If the earbuds do not connect to your device, place the earbuds back in their charging case, turn your device’s Bluetooth OFF and then back ON again, then repeat the pairing process. Your earbuds are designed to automatically sync to each other when they are turned ON, however if they ever fail to sync, please put both earbuds back into the charging case and try a factory reset.

Factory Reset: Before resetting your earbuds, go to your paired device’s Bluetooth list and remove (forget) the ‘Monster DNA Go’ earbuds.

Place both earbuds in the charging case and make sure that they are both placed securely and are charging (the Earbud LED indicator should be ON)
Press and hold the “Charging Case” button for 15s until the Charging Case LED indicator flashes red and white. The Earbud LED indicator will blink twice, then turn OFF.
Once the Charging Case LED Indicator stops flashing, remove both earbuds from the case and hold them near each other. The Earbud LED Indicator on both earbuds should flash quickly or 5s-10s, then turn off, followed by intermittent flashing of the Left Earbud LED Indicator only. If this does not happen, repeat the Factory Reset steps.
The Factory Reset is complete, and the earbuds will forget any previously paired devices. Follow the Bluetooth Pairing Instructions from the beginning to pair to a new device.

Charging the Case:
Connect the USB-C™ charging cable into the socket on the charging case. Plug the cable into a standard USB-C™ 5V / 1A output. (LED indicator will flash red or green depending on the battery level.) To check the charging case’s battery level, single press the Charging Case Button.

0-10% – The first LED is blinking red.
10-33% – The first LED is breathing; the others are OFF.
33-66% – The first LED is ON, the second is breathing, the third is OFF.
66-99% – The first and second LEDs is ON, the third LED is breathing.
100%- All three LEDs are ON.

You can also charge your case via any Qi™ compatible wireless charger (not included); a full charge should take approximately 2.5 hours.

Warning: To avoid damage to the charging case, please only use a 5V / 1A charger.

Charging the Earbuds:
To charge your earbuds, place them the charging case. The earbud LED indication will light up while they are charging and will turn oﬀ once they are fully charged. It’s recommended to fully charge your earbuds and charging case before ﬁrst use.

Warning: The earbuds can only be used with the provided charging case.

Responsible Party:

Company name: LIFEWORKS TECHNOLOGY GROUP LLC
Address: 530 7th Ave, 21st Floor | New York, NY 10018
Tel: 212.221.1863 ext. 1534
E-mail: slee@golifeworks.com

AN ICES-3 (B) / NMB-3 (B)
This Class B digital apparatus complies with Canadian ICES-003.

For French, Spanish and Portuguese instructions scan here: www.monsterforever.com

MONSTER-2MNTW0395-DNA-Go-In-Ear-Bluetooth-Earbuds-
fig-2

Package Includes:
Package Includes: (1) pair of wireless earbuds, (1) charging case, (1) charging cable, (12) pairs of ear tips, (1) user manual Warranty: 2 Year Limited Lifetime Warranty See more at www.monsterforever.com 2022 © The M Monster logo and Pure Monster Sound are trademarks or registered trademarks that are used under license of Monster, Inc. 2022 © All rights reserved. Manufactured, marketed, and distributed by Lifeworks Technology Group LLC. under license. New York, NY 10018. All other trademarks are the property of their respective owners.