dji RC Motion 2 Immersive Smart Controller User Guide

: June 13, 2024
: DJi

Table of Contents

dji RC Motion 2 Immersive Smart Controller
Lock Button
Accelerator
Activation
Disclaimer
Specifications
Compliance Information
Environmentally friendly disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

dji RC Motion 2 Immersive Smart Controller

dji-RCM-otion-2-Immersive-Smart-Controller-PRODUCT

Check battery level: press once.

dji-RCM-otion-2-Immersive-Smart-Controller-FIG-1
Power on/off: press then press and hold.

Power on the aircraft and the goggles
Make sure that the aircraft is linked with the goggles.

Press and hold the power button of the aircraft until the battery level indicators blink in sequence.
Press and hold the power button of the controller until it beeps continually and the battery level indicators blink in sequence.
The controller stops beeping when linking is successful and the battery level indicators turn solid and display the battery level.

Lock Button

dji-RCM-otion-2-Immersive-Smart-Controller-FIG-5

Takeoff: press twice to start the aircraft motors and then press and hold to make the aircraft take off. The aircraft will ascend to approximately 1.2 m and hover.

Landing: while the aircraft is hovering, press and hold to land the aircraft and stop the motors.

Brake : press during flight to make the aircraft brake and hover in place. Press again to unlock the attitude.

Joystick
Toggle up or down to make the aircraft ascend or descend. Toggle left or right to make the aircraft horizontally move left or right.

Mode Button
Press to switch between Normal and Sport mode. Press and hold to initiate RTH.

FN Dial
Press the dial to open the camera settings panel in the FPV view of the goggles. Scroll the dial to navigate the settings menu or adjust the parameter value, then press the dial to confirm the selection. Press and hold the dial to exit the current menu. Use the FN dial to control the camera tilt before takeoff or during RTH and landing. Press and hold the FN dial from the FPV view and then scroll up or down to tilt the camera. Release the dial to stop the camera tilt.

Shutter/Record Button
Press once: take a photo or start/stop recording.
Press and hold: switch between the photo and video modes.

Accelerator

Press to fly the aircraft in the direction of the circle in the goggles. Push forward to fly the aircraft backward. Apply more pressure to accelerate. Release to stop and hover.

Activation

When all devices are powered on and linked, connect the USB-C port of the goggles to the mobile device and run the DJI Fly app. The app will automatically identify the DJI RC Motion 2 and activate it in silent
mode. Activate the device as soon as possible after purchase to avoid affecting the after-sales service.

Disclaimer

By using this product, you signify that you have read, understand, and accept the terms and conditions of this guideline and all instructions at https://www.dji.com/rc-motion-2. EXCEPT AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT THE PRODUCT AND ALL MATERIALS AND CONTENT AVAILABLE THROUGH THE PRODUCT ARE PROVIDED “AS IS” AND ON “AS AVAILABLE BASIS” WITHOUT WARRANTY OR CONDITION OF ANY KIND. This product is not intended for children.

Specifications

Model Number RM220
Weight Approx. 170 g

Operating

Temperature -10° to 40° C (14° to 104° F)
Frequency 2.4000-2.4835 GHz 5.725-5.850 GHz (not available in some countries or regions)

Transmitter

Power (EIRP) 2.4 GHz: <30 dBm (FCC), <20 dBm (CE/SRRC/MIC)
5.8 GHz: <30 dBm (FCC), <23 dBm (SRRC), <14 dBm (CE)

Compliance Information

FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI RC Motion 2
Model Number: RM220
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declare that the above- mentioned model was tested to demonstrate compliance with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
This remote controller device complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions to satisfy RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 4 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the limbs.

ISED Compliance Notice
CAN ICES-003 (B) / NMB-003(B)
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two
conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with RSS‐102 radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions to satisfy RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI RC Motion 2) is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro- compliance contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI RC Motion is in compliance with the essential requirements and other relevant provisions of Radio Equipment
Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is free. The owner of old appliances is responsible for bringing the appliances to these collection points or to similar collection points. With this little personal effort, you contribute to recycling valuable raw materials and the treatment of toxic substances. Copyright © 2023 DJI All Rights Reserved.