STEiNEL HL 2020 E Professional Heat Guns Instruction Manual

STEiNEL HL 2020 E Professional Heat Guns

Product Information

• The product is a hot air tool manufactured by STEINEL. It is available in different models, including HG 2320 E, HL 2020 E, HL 1920 E, HL 1820 S, and HL 1620 S. The tool can be used for various applications such as soldering, welding PVC, shaping, drying, shrink-fitting, and stripping paint.
• All STEINEL hot air tools are manufactured to the highest standards and undergo strict quality control processes to ensure safety and reliability.
• The tool is double insulated, marked with the words “Double Insulated,” and equipped with a two-prong plug. It has a special insulation system that complies with applicable UL standards and does not require grounding. The tool can use either a two or three-prong extension cord.
• The appliance has a polarized plug, with one blade wider than the other. It is intended to fit in a polarized outlet only one way to reduce the risk of electric shock. If the plug does not fit fully in the outlet, it should be reversed. If it still does not fit, a qualified electrician should be contacted. Modifying the plug in any way is not recommended.

Product Usage Instructions

1. Read and follow the important safety instructions provided in the user manual before using the tool.
2. Do not use the tool near flammable liquids or in an explosive environment.
3. Always hold the tool by its plastic enclosure. The metal nozzle requires approximately 20 minutes to cool down before it can be touched. Do not touch the nozzle or accessory tips until they are cool.
4. Do not store the tool until the nozzle has cooled to room temperature. Place the tool in a clear area away from combustible materials while it cools.
5. Do not cut off airflow by placing the nozzle too close to the workpiece. Keep the intake vents clean and clear of obstructions.
6. Do not use the tool in a bath or over water.
7. Safety glasses should be worn when using the tool.
8. It is recommended to wear leather gloves when using the hot air tool.
9. Always unplug the tool after use.
10. Extreme care should be taken when stripping paint. Follow the provided guidelines, including moving the workpiece outdoors or ensuring a well-ventilated work area, removing or covering any carpets, rugs, furniture, clothing, cooking utensils, and air ducts, placing drop cloths to catch any residue, and working in one room at a time.

MODELS

IMPORTANT SAFETY INSTRUCTIONS

READ THESE INSTRUCTIONS

WARNING: Read this instruction book before using. To reduce risk of fire or electric shock, do not expose to rain or moisture. Store indoors. Double insulated. When servicing, use only identical replace-ment parts. When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock and personal injury. This hot air gun operates at 1200°F with no visual indication of temperature (no flame). Never leave device unattended. Otherwise risk of fire. The heat stream at the outlet nozzle will burn flesh. Do not turn on hot air tool with hand in front of nozzle.

DO NOT USE NEAR COMBUSTIBLE LIQUIDS. DO NOT USE FOR:

• Heating gas engines
• Heating car batteries
• Thawing refrigerator equipment.
• WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects, or other repro-ductive harm.
• Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber.
• Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

WARNING!

• This tool is capable of producing temperatures up to 1200° F of flameless heat at the nozzle. ALWAYS:
• Direct the heat away from yourself and others.
• Prevent ignition of combustible materials on or near the workpiece.
• Prevent blockage of intake and nozzle openings.
• Keep a fully charged fire extinguisher on hand.
• Allow the nozzle and accessory tips to cool to room temperature before storage.

Cautions

1. WARNING: Hidden areas such as behind walls, ceilings, floors, soffit boards and other panels may contain flammable materials that could be ignited by the hot air tool when working in these locations. The ignition of these materials may not be readily apparent and could result in property damage and injury to persons. Do not use if in doubt about this hazard. When working in these locations, keep the hot air tool moving in a back-and-forth motion. Lingering or pausing in one spot could ignite the panel or the material behind it.
2. This hot air tool can produce up to 1200° F of flameless heat at the nozzle. Do not direct airstream at clothing, hair or other body parts. Do not use as a hair dryer.
3. Do not use near flammable liquids or in an explosive environment (fumes, gases or dust). Remove materials or debris, that may become ignited from work area.
4. Always hold tool by plastic enclosure. The metal nozzle requires approximately 20 minutes to cool to where it can be touched. Do not touch nozzle or accessory tips until cool.
5. Do not store tool until nozzle has cooled to room temperature. Place tool in a clear area away from combustible materials while cooling.
6. Do not cut off airflow by placing nozzle too close to work piece. Keep intake vents clean and clear of obstructions.
7. Place tool on a level surface when tool is not hand held. Place cord in a position that won’t cause tipping.
8. Do not leave tool unattended while running or cooling down. Otherwise risk of fire.
9. Keep a fully charged fire extinguisher nearby.
10. Do not direct airflow directly on glass.
11. Shield materials around the heated area to prevent damage or fire.
12. Use only with 120 V AC voltage.
13. Do not use in wet conditions.
14. Not to be used by children. This is not a toy and should be respected.
15. Do not use in bath or over water.
16. Safety glasses should be worn when using this tool.
17. It is recommended that leather gloves be worn when using a hot air tool.
18. Always unplug after use.
19. WARNING: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint may contain lead, which is poisonous. Any pre-1977 paint may contain lead and paint applied to homes prior to 1950 is likely to contain lead. Once deposited on surfaces, hand to mouth contact can result in the ingestion of lead. Exposure to even low levels of lead can cause irreversible brain and nervous system damage; young and unborn children are particularly vulnerable. Before beginning any paint removal process you should determine whether the paint you are removing contains lead. This can be done by your local health department or by a professional who uses a paint analyzer to check the lead contact of the paint to be removed. LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL AND SHOULD NOT BE REMOVED USING A HOT AIR TOOL.
20. Do not allow dust, debris or other contamination to enter the heat blower air intake.
    They may ignite or cause damage to the tool.

Persons removing materials should follow these guidelines.

1. Move the work piece outdoors. If this is not possible, keep the work area well ventilated. Open the windows and put an exhaust fan in one of them. Be sure the fan is moving the air from inside to outside.

2. Remove or cover any carpets, rugs, furniture, clothing, cooking utensils and air ducts.

3. Place drop cloths in the work area to catch any residue. Wear protective clothing such as extra work shirts, overalls and hats.

4. Work in one room at a time. Furnishings should be removed or placed in the center of the room and covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths.

5. Children, pregnant or potentially pregnant women and nursing mothers should not be present in the work area until the work is done and all clean up is complete.

6. Wear a dust respirator mask or a dual filter (dust and fume) respirator mask which has been approved by the Occupational Safety and Health Administration (OSHA), the National Institute of Safety and Health (NIOSH), or the United States Bureau of Mines. These masks and replaceable filters are readily available at major hardware stores. Be sure the mask fits. Beards and facial hair may keep masks from sealing properly. Change filters often.
   DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.

7. Use caution when operating the hot air tool. Keep the hot air tool moving as excessive heat will generate fumes which can be inhaled by the operator.

8. Keep food and drink out of the work area. Wash hands, arms and face and rinse mouth before eating or drinking. Do not smoke or chew gum or tobacco in the work area.

9. Clean up all removed residue and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surface where residue or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate detergent or trisodium phosphate (TSP) to wash and mop areas.

10. At the end of each work session put the residue and debris in a double plastic bag, close it with tape or twist ties, and dispose of properly.

11. Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest of the dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work clothes. Wash hair and body thoroughly with soap and water.

Thank you

• Thank you for choosing a STEINEL hot air tool. This tool can be used for completing a wide range of jobs safely and reliably, such as soldering, welding PVC, shaping, drying, shrink-fitting, stripping paint, etc. All STEINEL tools are manufactured to the highest standards and undergo a strict process of quality control. Used in the proper manner, this hot air tool will give you lasting satisfaction.

Double Insulated Tools

• Tools marked with the words “Double Insulated” are equipped with a two prong plug. These tools have a special insulation system that complies with applicable UL standards They do not require grounding.
• Double Insulated” tools, like this one, have two prong cords and can use either a two or three prong extension cord.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

Extension Cords

• As the distance from the supply outlet increases, heavier gauge extension cords are required. The use of extension cords of inadequate size wire causes a serious drop in voltage and loss of power. Protect the cord from damage. Keep cords away from excessive heat, sharp edges and damp or wet areas. Repair or replace damaged extension cords before using.

Conversion °C to °F

Conversion °F to °C

For Your Safety

(HG 2320 E / HL 2020 E / HL 1920 E / HL 1820 S / HL 1620 S)

• First time use, a small quantity of smoke may occur when the tool is used for the first time. This smoke is caused by binding agents released from the heater’s insulating film during the first time of use. To let the smoke escape quickly, the tool should be set down on its standing surface. The area you are working in should be well ventilated when using the tool for the first time. Any smoke coming out of the tool is not harmful!

Residual heat indicator (HL 2320 E / HG 2020 E)

• The residual heat indicator serves as a visual warning to prevent injury from direct contact with the hot nozzle outlet by flashing until the temperature at the nozzle outlet has fallen below 140 degrees F at room temperature. It begins working after the tool has been in use for 90 seconds and also works when the
  tool is unplugged. No indication will be shown if the tool has been in operation for less than 90 seconds. Responsibility always rests with the user and care must be taken at all times when handling hot air tools.

These hot air tools are protected from overheating:

• The thermal cut-out completely shuts down the tool if it is overloaded.

Tool description

Operation

Please note: The distance from the object you are working on depends on material and intended method of working. Always try out the airflow and temperature on a test piece first. Using the attachable accessory nozzles (see accessories page on the cover) the flow of hot air can be controlled with maximum precision. Take care when changing hot nozzles! When using the hot air tool in the self-resting position, make sure it is standing on a stable, non- slip and clean surface.

HG 2320 E

Technical Specifications HG 2320 E

Item No.| 110025598
Temperature| 120°F – 1200°F (49°C – 649°C)
Airflow| Continuously variable 4-13 cfm (+/- 0.5)
Switch| Cool air stage,

variable temperature & airflow

Programs| Four customizable pre-set temperature/airflow programs
Output| 1600 watts
Voltage| 120 VAC / 60 Hz
Amps| 13.3
Power Cord| Industrial grade rubber, length: 6 ft
Nozzle Diameter| 1.30″ (33.02 mm)
Dimensions| 9.96″ x 3.41″ x 7.87″ (l x w x h)
Net Weight| 2.19 Ibs (35.10 oz)
Single Sell Pack| Dimensions: 10.20″ x 3.54″ x 9.33″

Weight: 2.60 Ibs (41.66 oz)

Warranty| One year limited
|

1. Operation
   • The tool is switched on and off at a two-stage switch on the back of the grip handle. The toggle is used for controlling temperature and airflow respectively for speed.
2. Setting temperature
   • The hot air tool is factory set to display the temperature in °F. Stage 1 is the cooling stage, temperature is always 120 °F. Use the cooling function for drying paint, cooling workpieces or for cooling the nozzle before changing the accessory attachment. In stage 2 temperature is continuously variable over a range of 120 °F -1200 °F on the control panel with LCD display. The actual temperature is measured at the nozzle outlet and indicated on the display. The toggle is used as an input button with plus/minus function. The temperature setting range begins at 120 °F and ends at a maximum of 1200 °F. Briefly pressing the “+/–” toggle increas-es or reduces the temperature setting in 10° steps. Keeping the toggle pressed speeds up the temperature setting process. Once the temperature has been set, the tool takes a few seconds to reach temperature (depending on speed/airflow). The temperature setting selected is shown on the display for 3 seconds. The display then shows the current actual temperature. The “°C/°F” symbol continues to flash until the selected temperature is reached. If you want to alter the setting, simply press the toggle again to increase or reduce the temperature. After switching off, the hot air tool stays in the last setting.
3. Setting airflow rate
   • To change the airflow rate, first press the “airflow” button; the fan symbol flashes. Now use the toggle to set the airflow rate. The airflow rate setting mode automatically closes if the airflow rate setting is not changed within 5 sec. Pressing the airflow button again after setting the airflow rate immediately closes the airflow rate setting mode. The airflow rate can be varied from a minimum of 4 cfm to a maximum of 13 cfm (+/- 0.5 cfm).
4. Programming mode [P]
   • Besides normal operating mode, the HG 2320 E also has four factory-set programs for the most frequent jobs. Four programs are factory-set for the most common types of work. Press button “P” for programming mode. Number 1 is displayed for program 1. Continuing to press the program button will take you to programs 2-4. Pressing the button again will return the tool to normal operation.

Preset Programs

Memory function [S]

The values selected for the four programs can be changed and memorized at any time. To do this, first press the program button “P” until the display shows the program you wish to change. Set the temperature
and airflow rate you require. Memory symbol on the LCD flashes to indicate that the user program selected has been changed. To memorize this setting in the user program selected, press and hold down the program selector button. The memory symbol continues to flash for approx. 2 sec. The settings entered are saved once the memory symbol stays on all the time. To return to normal operation, press the program button until the program symbol disappears from the display.

Technical Specifications HL 2020 E

Item No.| 110025597
Temperature| 120°F – 1150°F (49°C – 621°C)
Airflow| 4 / 4-8 / 6-13 cfm (+/- 0.5)
3 Stage Switch| Cool air stage 120°F / 4 cfm Variable temperature 4-8 cfm Variable temperature 6-13 cfm
Output| 1600 watts
Voltage| 120 VAC / 60 Hz
Amps| 13.3
Power Cord| Industrial grade rubber, length: 6 ft
Nozzle Diameter| 1.30″ (33.02 mm)
Dimensions| 9.96″ x 3.37″ x 7.87″ (l x w x h)
Net Weight| 2.19 Ibs (35.10 oz)
Single Sell Pack| Dimensions: 10.20″ x 3.54″ x 9.33″

Weight: 2.60 Ibs (41.66 oz)

Warranty| One year limited

The tool is switched on and off at the three-stage switch on the back of the grip handle. In addition to three-stage speed/airflow control, temperature can be continuously adjusted over a range of 120 °F to 1150 °F in settings 2 and 3 at the toggle. The tool is factory set to display the temperature in °F. The target temperature can be increased in 10 °F steps by pressing the right-hand “+” side of the toggle or reduced in 10 °F steps by pressing the left-hand “–” side of the toggle. Pressing the toggle briefly increases or reduces the target temperature by one 10 °F step. Keeping the toggle pressed will continue to increase or reduce the tem-perature in steps of 10 °F until the toggle is released or the minimum or maximum temperature is set. The temperature setting is shown on the display for 3 seconds. On lowering or increasing the temperature, the actual temperature at the nozzle outlet is displayed. The °C/°F symbol flashes during this period. As soon as the selected temperature is reached, this symbol stops flashing and is displayed all the time. Blower switch 1 delivers a temperature of 120 °F. When the tool has been operating at high temperatures on blower switch 2 or 3 it will take a short while to cool to 120 °F after switching down to blower stage 1. While the tool is cooling down, the LCD display shows the actual temperature at the nozzle outlet. After switching off, the tool stays in the last setting that was selected. The protection tube detaches from the housing allowing accessor-ies to be attached. Please see page 10 for the procedure to change the power cord.

Technical Specifications HL 1920 E

Item No.| 110025596
Temperature| 120°F – 1100°F (49°C – 593°C)
Airflow| 4 / 4-8 / 6-13 cfm (+/- 0.5)
3 Stage Switch| Cool air stage 120°F / 4 cfm Variable temperature 4-8 cfm Variable temperature 6-13 cfm
Output| 1500 watts
Voltage| 120 VAC / 60 Hz
Amps| 12.5
Power Cord| Industrial grade rubber, length: 6 ft
Nozzle Diameter| 1.30″ (33.02 mm)
Dimensions| 9.96″ x 3.33″ x 7.87″ (l x w x h)
Net Weight| 1.9 Ibs ( 30.37 oz)
Single Sell Pack| Dimensions: 10.20″ x 3.54″ x 9.33″

2.31 Ibs (36.93 oz)

Warranty| One year limited

The tool is switched on and off at the three-stage switch on the back of the grip handle. In addition to three-stage speed/airflow control (stage 1 is a cool-air stage at 120 °F), temperature can be continuously adjusted over a range of 120 °F – 1100 °F in settings 2 and 3 at the thumbwheel. The numbers 1-9 on the thumbwheel serve as a guide only. Whereas “1” means 120 °F, the maximum temperature of 1100 °F is attained at setting “9”. Airflow can be adjusted to the three stages of 4 / 4-8 / 6-13 cfm. The protection tube detaches from the housing allowing accessories to be attached.

Thumbwheel Temperature Guide

| Air flow stage II| Air flow stage III
Setting wheel|

Temperature approx.

1| 80 °C / 175 °F| 80 °C / 175 °F
2| 100 °C / 210 °F| 100 °C / 210 °F
3| 180 °C / 355 °F| 180 °C / 355 °F
4| 270 °C / 518 °F| 260 °C / 500 °F
5| 330 °C / 625 °F| 320 °C / 610 °F
6| 410 °C / 770 °F| 390 °C / 735 °F
7| 480 °C / 895 °F| 460 °C / 860 °F
8| 560 °C / 1040 °F| 530 °C / 985 °F
9| 600 °C / 1100 °F| 600 °C / 1100 °F

HL 1820 S

Technical Specifications HL 1820 S

Item No.| 110025541
3 Stage Switch| Cool air stage 120°F / 4 cfm 750 °F (399°C) / 7 cfm

1100 °F (593°C) / 13 cfm

Output| 1400 watts
Voltage| 120 VAC / 60 Hz
Amps| 11.7
Power Cord| Industrial grade rubber, length: 6 ft
Nozzle Diameter| 1.30″ (33.02 mm)
Dimensions| 9.96″ x 3.33″ x 7.87″ ( l x w x h)
Net Weight| 1.77 Ibs (28.36 oz)
Single Sell Pack| Dimensions: 10.20″ x 3.54″ x 9.33″

Weight: 2.18 Ibs (34.92 oz)

Warranty| One year limited

The tool is switched on and off at the three-stage switch on the back of the grip handle. Air flow and temper-ature can be adjusted to 3 settings. Stage 1 is a cool-air stage at 120 °F with an air flow rate of 4 cfm. Stage 2 reaches 750 °F at an air flow of 7 cfm, stage 3 delivers 1100 °F at 13 cfm. The protection tube detaches from the housing allowing accessories to be attached.

Technical Specifications HL 1620 S

Item No.| 110023455
2 Stage Switch| 575 °F (302°C) / 8 cfm

950 °F (510°C) / 13 cfm

Output| 1300 watts
Voltage| 120 VAC / 60 Hz
Amps| 10.8
Power Cord| Industrial grade rubber, length: 6 ft
Nozzle Diameter| 1.30″ (33.02 mm)
Dimensions| 9.92″ x 3.37″ x 7.87″ (l x w x h)
Net Weight| 1.65 Ibs (26.4 oz)
Single Sell Pack| Dimensions: 10.20″ x 3.54″ x 9.3″

Weight: 2.06 Ibs (32.98 oz)

Warranty| One year limited

The tool is switched on and off at the two-stage switch on the back of the grip handle. Airflow and temperature can be adjusted between 2 settings. Stage 1 reaches 575 °F at an airflow of 8 cfm, stage 2 reaches 950 °F at 13 cfm.

Changing the power cord

Important! Disconnect tool from power supply

If the power cord is damaged, it can easily be changed without opening the housing.

1. Undo screw d and pull off cover cap a.
2. Release cable grip b.
3. Undo mains terminals c
4. Pull out cable e.
5. Insert new cable and secure in reverse order (Firmly screw down mains terminals etc.).

Applications

Shrink tubing on cables:

• The shrink tubing is slipped over the section you want to insulate and heated with hot air. The tubing shrinks by approx. 50% in diameter to give a sealed union. Shrinking is particularly fast and even using reflector nozzles. Sealing and stabilizing cable breaks, insulating soldered joints, gathering cable runs, sheathing terminal blocks.

Forming PVC:

• Sheeting, piping or ski boots can be softened and formed with hot air.

Thawing:

• Water pipes, frozen door locks, steps. Gently thaws and dries all in one go.

Soldering:

• First, clean metal parts you want to join. Then, using hot air, heat the point you want to solder and offer up the soldering wire. Use flux or a soldering wire with a flux core to prevent oxide forming.

Welding and joining plastic:

• All parts being welded must be of the same plastic material. Use an appropriate welding rod.

Joining plastic sheeting:

• The sheets are overlapped and welded together. A slit nozzle is used to direct hot air under the overlap, then the two sheets are firmly pressed together with a feed roller.
• Also possible: Repairing PVC tarpaulins by overlap welding with a slit nozzle.

Shaping:

• Ski boots and sports shoes can be shaped for a perfect fit.

Desoldering:

• Electronic components are detached quickly and neatly from circuit boards with a reduction nozzle.

Welding sheeting:

• The sheets are overlapped and welded together. A slit nozzle is used to direct hot air under the overlap, then the two sheets are firmly pressed together with a feed roller.
• Also possible: Repairing PVC tarpaulins by overlap welding with a slit nozzle.

Plastic types:

Material| Application types| Distinguishing characteristics
Rigid PVC| Piping, fittings, boards, building profiles, technical molded components, etc.

Welding temperature

550 – 650 °F (290 – 345 °C)

| Incineration test: carbonizes in the flame and extinguishes on its own

Smoke odor: pungent, of hydrochloric acid

Drop test: crashing

Plasticized PVC| Floor coverings, wallpaper, hoses, sheets, tools, etc.

Welding temperature

550 – 650 °F (290 – 345 °C)

| Incineration test: smoking, yellowish-green flame

Smoke odor: pungent, of hydrochloric acid

Drop test: silent

Plasticized PE

(LDPE)

Polyethylene

| Domestic and electronic items, toys, bottles, etc.

Welding temperature

450 – 550 °F (230 – 290 °C)

| Incineration test: light, yellow flame, drops continue to burn

Smoke odor: resembles an extinguished candle

Drop test: dull

Hard PE

(HDPE)

Polyethylene

| Baths, baskets, canisters, insulating materials, piping, cellar shafts, transport containers, waste bins, etc.

Welding temperature

550 – 650 °F (290 – 345 °C)

| Incineration test: light, yellow flame, drops continue to burn

Smoke odor: resembles an extinguished candle

Drop test: crashing

PP

Polypropylene

| HT drainpipes, plastic chairs, packaging, car components, equipment housing, technical moldings, battery boxes, etc.

Welding temperature

450 – 550 °F (230 – 290 °C)

| Incineration test: light flame with a blue core, drops continue to burn

Smoke odor: pungent odor of paraffin

Drop test: crashing

ABS| Car components, equipment housing, suitcases

Welding temperature

625 – 725 °F (330 – 385 °C)

| Incineration test: black, fluffy smoke

Smoke odor: sweetish

Drop test: crashing

Accessories

Your retailer has a wide range of accessories for you to choose from.

1. Window nozzle 75 mm Part No. 110048749
2. Window nozzle 50 mm Part No. 110048750
3. Spreader nozzle 75 mm Part No. 110048749
4. Spreader nozzle 50 mm Part No. 110048643
5. Reflector nozzle 39 mm Part No. 110048645
6. Lap Welding Nozzle 20 mm Part No. 110048649
7. Reduction nozzle 14 mm Part No. 110048647
8. Wire protection tube Part No. 07404
9. Silicone seam roller Part No. 01250
10. Reduction nozzle 9 mm Part No. 110048646
11. Reflector nozzle 9 mm Part No. 110048646
12. Reflector nozzle 14 mm Part No. 110048752
13. Reflector nozzle with sieve Part No. 01029
14. Pinpoint reducer Part No. 07082
15. Welding nozzle Part No. 110048648
16. Plastic welding rod rigid PVC Part No. 110048754
17. Plastic welding rod HDPE Part No. 110048753
18. Plastic welding rod PP Part No. 110048757
19. Plastic welding rod ABS Part No. 110048756
20. Thermo flex welding rod Part No. 07352
21. Wire mesh Part No. 07371
22. Welding iron Part No. 109428400
23. Temperature guard Part No. 07666
24. Fine dust particle filter Part No. 07821
25. Temperature detection device HL-Scan Part No. 110048403
26. Flexible stand VACUUM Part No. 01435
27. Flexible stand MAGNETIC Part No. 01445
28. Case Part No. 110036523
29. xx20 Plastic Ring/hanger Part No. 110045172
30. LED Light Part No. 110047650

Special Accessories

Spare Parts List HG 2320 E

Wiring Diagram HG 2320 E

Spare Parts List HL 2020 E

Wiring Diagram HL 2020 E

Spare Parts List HL 1920 E

Wiring Diagram HL 1920 E

Spare Parts List HL 1820 S

Wiring Diagram HL 1820 S

Spare Parts List HL 1620 S

Wiring Diagram HL 1620 S

Limited Warranty

• STEINEL warranties its hot air tools, if properly operated and maintained, and used under normal conditions, for a period of one (1) year from the date of purchase. Warranty does not apply to wearable items such as heating elements which require periodic replacement. Specifically EXCLUDED from warranty are tools that have been subject to abuse, tools that have been opened or repaired by anyone other than STEINEL, tools that have been modified in any way or mounted onto machinery/equip-ment, and tools that have been put into continuous operation. These are hand held power tools and are intended for use as such. Any other use voids STEINEL’s warranty.

Warranty and Repair Procedures

• In the event of product failure, please call STEINEL customer service directly at
  800-852-4343. We will attempt to troubleshoot the difficulty via phone.

• If warranty work or other repair appears necessary, we will issue an RGA# and we will supply you with a shipping address (postage paid by the customer), with the RGA# clearly marked, and accompanied by a brief description of the difficulty as well as your original dated sales receipt phone number and return address.

• When received, STEINEL will diagnose the problem and determine if it is covered under warranty. If we determine that it is covered by warranty, we will repair or replace the defective tool, at our option, and return it to the customer (postage paid by STEINEL). If we determine that the tool is not defective and/or that it is not covered by warranty, we will contact the customer to discuss options prior to performing any repair work not covered under warranty.

• All non-warranty repair work is billed at standard rates and will be quoted prior to repair.

Consequential Damages

• The company shall not be liable for any incidental or consequential damages arising from the use of the Product by the Purchaser, the breach of any warranties, the fail-ure to deliver, delay in delivery, delivery in non-conforming condition, or for any other breach of contract or duty between the Company and the Purchaser.
• Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Disclaimers of warranties

• The warranties contained herein are expressly in lieu of any other expressed or implied warranties, or any other obligation on the part of the Company. Any implied warranty of merchantability or fitness for a particular purpose shall expire one (1) year after
  the date the product is purchased by the original end-user Purchaser.

• Any models, drawings, plans, specifications, affirmations of fact, promises, or other communications by the Company with reference to the performance of the product are solely for the convenience of the Purchaser and shall not in any way modify the expressed warran-ties and disclaimers set forth herein.

• The Purchaser acknowledges it is purchasing the Product solely on the basis of the commitments of the Company as expressly set forth herein. No agents or other parties are authorized to make any warranties on behalf of the Company or to assume for the Company any other liability in connection with the Product. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Limitation of actions

• Any action resulting from the breach of any warranty contained herein by the Company must be commenced within one (1) year after the cause of action accrues.
• In no event shall the Company’s total liability for any or all breaches of any warranty exceed the actual purchase price of the Product.

Other rights

• This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
• 1.888.610.7664
• www.calcert.com
• sales@calcert.com

Documents / Resources

| STEiNEL HL 2020 E Professional Heat Guns [pdf] Instruction Manual
HL 2020 E, HG 2320 E, HL 1820 S, HL 1620 S, HL 1920 E, HL 2020 E Professional Heat Guns, HL 2020 E, Professional Heat Guns, Heat Guns, Guns
---|---
| STEiNEL HL 2020 E Professional Heat Guns [pdf] Instruction Manual
HL 2020 E Professional Heat Guns, HL 2020 E, Professional Heat Guns, Heat Guns, Guns
| STEiNEL HL 2020 E Professional Heat Guns [pdf] Instructions
HL 2020 E Professional Heat Guns, HL 2020 E, Professional Heat Guns, Heat Guns, Guns
| STEiNEL HL 2020 E Professional Heat Guns [pdf] Instruction Manual
HL 2020 E, HG 2320 E, HL 2020 E Professional Heat Guns, Professional Heat Guns, Heat Guns, Guns

References

• Calcert

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>