Reina DE-INS1502S Ines Designer Towel Rail Installation Guide

Reina DE-INS1502S Ines Designer Towel Rail

Product Information

The Electric Towel Rail is a wall-mounted device designed to provide warmth and dryness to towels. It comes in three different sizes: DE-INS1502C, DE- INS1502K, and DE-INS1502S. Each size is available in a different color: Chrome, Black, and Brushed Brass. The towel rail operates at a power of 35W for DE-INS1502C and DE-INS1502S, and 40W for DE-INS1502K. It requires a voltage of 230VAC and operates at a frequency of 50HZ.

Product Usage Instructions

1. Step 1: Select the desired position on the wall for installation. Use a measuring tape to determine the distance between the center points of each wall bracket tube. Mark the location with a pencil.
2. Step 2: Use an electric driller to make holes in the marked locations on the wall. Ensure to drill a hole for the core cable going from the mounting leg to the wall. Knock plastic wall anchors into the wall using a hammer.
3. Step 3: Insert one M445 screw through the fixing block and two M430 screws through the mounting seat. Secure them into the plastic wall anchors using an electric drill. Place the decorative cap onto the mounting seat and tighten it.
4. Step 4: Connect the core wire from the leg to the power wire inside the wall. Fix the towel rail tube onto the mounting brackets. Use the Allen wrench to install the hex screws into the holes of all the tubes to complete the installation.

Warning:
After installation, it is recommended to have grounding and short circuit measurements performed by a licensed electrician to prevent potential safety hazards.

How to Use the Timer on the Towel Rail?
To use the timer function on the towel rail, follow these steps:

1. To power on the towel rail for a consistent 24 hours, press the right button on the display. The digital screen will show “ON”.
2. If you want to use the boost timer function, press the left button. The display will show “2H- 4H- A2- A4”. Use the blue cursor between two words on the display to select the desired timing mode.

Safety Instruction

Please read this instruction carefully before installation and operation.

Warning:
This device must be installed by a licensed electrician.

• This Towel Rail is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the Towel Rail by a person responsible for their safety.
• In order to avoid a hazard, this Towel Rail must be installed so that the bottom rail is at least 600mm above the floor.
• This Towel Rail is intended to warm and dry towels and therefore is hot to the touch.
• The towel rail is to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
• To avoid a hazard this towel rail must not be used to hold towels or any other articles that have been in contact with oil, petroleum-based products, or dry cleaning fluids.
• Use this Towel Rail only with the voltage specified on the rating label.
• Do not immerse in liquid or allow liquid to run into the interior of the Towel Rail. Indoor use only.
• Do not operate this towel rail if damaged or after the Towel Rail malfunctions or has been dropped or damaged in any manner. Return to a qualified electrical person for examination, electrical service or repair.
• Use this Towel Rail only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electrical shock, or injury.
• Do not use this Towel Rail in a window as rain may cause electric shock.

TOOLS REQUIRED

• Pencil
• Hammer
• Measuring Tape
• Hex key
• Screwdriver
• Spirit level
• Electric drill

ACCESSORIES

TECHNICAL SPECIFICATIONS

INSTALLATION GUIDE

• STEP 1: Select the desired position, then utilize a measuring tape to determine the distance between the center points of each wall bracket tube, and mark the location with a pencil.
• STEP 2: Make the holes with an electric driller; Be sure to drill a hole for the core cable going from the mounting leg to the wall. And use a hammer to knock plastic wall anchors into wall completely.
• STEP 3: Insert one M445 screw through the fixing block and two M430 screws through the mounting seat and then secure them into the plastic wall anchors with an electric drill. Place the decorative cap onto the mounting seat and tighten it.
• STEP 4: Connect the core wire from the leg to the power wire inside the wall. Then fix the towel rail tube onto the mounting brackets, and use the Allen wrench to install the hex screws into the holes of all the tubes to complete the installation.

Warning:
To prevent potential safety hazards, it is recommended that grounding and short circuit measurements be performed after installation of the device. This should be done by a licensed electrician.

HOW TO USE THE TIMER ON THE TOWEL RAIL

TIMER working mode:

1. Consistent 24 hours ON.
2. 2H: 2 hours ON, timer will countdown(2H-1H) and stop working automatically after 2 hours.
3. 4H: 4 hours ON, timer will countdown(4H-3H-2H-1H) and stop working automatically after 2 hours.
4. A2( Automatic working mode), 2 hours ON, 2 hours OFF, then 2 hours ON and 2 hours OFF automatically working as circulation way, timer will countdown automatically(A2-A1).
5. A4( Automatic working mode), 4 hours ON, 4 hours OFF, then 4 hours ON and 4 hours OFF automatically working as circulation way, timer will countdown automatically(A4-A3-A2-A1).

Only by Pressing the right button on the display, it is powered on and simultaneously it will work for a consistent 24 hours, ON showing on the digital screen.

If you want to use the boost TIMER working by hours, then press the left button , you can select 2H- 4H- A2- A4 (as above description), a blue cursor between two words on the display will flash to indicate the rail is beginning to work under current selected TIMING mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>