REINA WAVE Horizontal Radiator Installation Guide
- June 3, 2024
- Reina
Table of Contents
WAVE Horizontal Radiator
Installation Guide
WAVE (SİNGLE/DOUBLE)
INSTALLATION GUIDE
This product must be fitted only by a fully qualified installer.
WAVE Horizontal Radiator
| DESCRIPTION | DESCRIPTION | ILLUSTRATION |
|---|
RADIATOR x1| Fixing choose the appropriate fixing for the wall material if
required|
PTFE tape|
Electric drill| 
Masonry drill bit appropriate
to the fixings|
Adjustable spanner|
Radiator valve hex key|
TOP-RIGHT CLIPS x 1| TOP-LEFT CLIPS x1| Flat head and philips head
screw drivers|
1 lock shield valve and 1
gate or thermostatic valve|
BOTTOM – RIGHT CLIPS x 1| BOTTOM – LEFT CUPS el
Spirit level|
END PLUG x 1| FIXING SCREWS x 8| WASHERS x8
Measuring tape|
| WALL ANCHORS x8| GASKETS x 4
| 1- | SCREWS |
|---|---|
| 2- | WASHERS |
| 3- | CLIPS (BRACKETS) |
| 4- | WALL ANCHORS |
| 5- | WALL |
NAMES| A| B| C| TUBE (QTY)| DM| DO| H|
L
---|---|---|---|---|---|---|---|---
WAVE (SINGLE)| 600| 412| 545| 4| 34| 78| 480| 151
WAVE (SINGLE)| 600| 620| 545| 6| 34| 78| 480| 359
WAVE (SINGLE)| 600| 828| 545| 8| 34| 78| 480| 567
WAVE (SINGLE)| 600| 1036| 545| 10| 34| 78| 480| 775
WAVE (SINGLE)| 600| 1244| 545| 12| 34| 78| 480| 983
WAVE (SINGLE)| 600| 1452| 545| 14| 34| 78| 480| 1191
WAVE (SINGLE)| 1800| 412| 1745| 4| 34| 78| 1680| 151
WAVE (DOUBLE)| 600| 412| 545| 8| 68| 112| 480| 151
WAVE (DOUBLE)| 600| 620| 545| 12| 68| 112| 480| 359
WAVE (DOUBLE)| 600| 828| 545| 16| 68| 112| 480| 567
WAVE (DOUBLE)| 600| 1036| 545| 20| 68| 112| 480| 775
WAVE (DOUBLE)| 600| 1244| 545| 24| 68| 112| 480| 983
WAVE (DOUBLE)| 600| 1452| 545| 28| 68| 112| 480| 1191
WAVE (DOUBLE)| 1800| 412| 1745| 8| 68| 112| 1680| 151
NAMES| A| B| C| TUBE (QTY)| DM| DO| H|
L
---|---|---|---|---|---|---|---|---
WAVE (SINGLE)| 1800| 204| 1745| 2| 34| 78| 1680| 40
WAVE (DOUBLE)| 1800| 204| 1745| 4| 68| 112| 1680| 40
GENERAL RECOMMENDATION
- Before fitting the radiator it is necessary to wash out the heating system to remove any existing mud, scale, work residues, traces of flux, oil, etc.
- When the system water pH is outside the 5,5-8,5 range and/or when the dissolved is above 0,1mg/liter, it is always needed to protect the heating system components (the radiator is one of these) with a proper chemical treatment compatible with all parts in contact with water (silicon rubber too).
- In order to fit the radiator to the wall, it is necessary to choose the proper fixings for the wall material.
- If the system water exceeds 50°C, please install a warning mark near the radiator to avoid any accidental scalding.
- Maximum working temperature 95°C, maximum working pressure 4 bar.
- Clean the radiator surface only with a soft cloth to avoid scratching the finish and do not use chemical agents during cleaning operations. It is prohibited to climb on the radiator.