ORA-01 Fresca Fan User Manual

ORA-01 Fresca Fan

Product Information

• Product Name: ORA-01
• Product Description: The ORA-01 is a fan specifically designed for use in RVs.

Items supplied in package

• 1 x Main Fresca Fan unit (Item 1)
• 1 x Back mounting plate (Item 2)
• 2 x Screws (Item 3)
• 2 x 3.2 mm stainless steel nuts (Item 4)
• 1 x DC Power cable pair (Item 5)
• 2 x Locking washer (Item 6)
• 2 x 2.2 mm brass nuts (Item 7)
• 1 x Double sided tape (Item 8)

Product Usage Instructions

Installation – Preparing back mounting plate

Preparing of back mounting plate

• Identify the intended mounting location for the fan.
• Insert the 2 stainless steel nuts (Item 4) into the nut recess holes on both sides of the back mounting plate.
• Peel backing off from double sided tape (Item 8) supplied, and stick it onto the back of the back mounting plate.
• This is how the back of the plate will look like with the two nuts and double sided tape applied.
• Installation – Mounting of back mounting plate
• Mounting of back mounting plate
• Place the back mounting plate with the double sided tape facing towards the mounting location and stick the back mounting plate in place.
• Secure the back plate permanently at the intended location with 6 mm screws (not supplied) suitable for use in mounting of the fan.
• Installation – Connecting the power cables

Electrical wiring

• Locate the two DC power terminals at the bottom of the fan unit marked (+) Positive and (-) Negative.
• Connect the supplied DC power cable pair (Item 5) onto the two terminals, following the correct order: DC power cable pair, locking washers (Item 6), and brass nuts (Item 7).
• Tighten all brass nuts on the two (+) Positive & (-) Negative terminals with a pliers or wrench. Do not tighten by hand ONLY.

Installation – Routing the cable and mounting

Routing the cable and mounting

There are three options for routing the DC power cables:

• Option 1: Via bottom groove notch
• Option 2: Via top groove notch
• Option 3: Via hole on the back mounting plate (may require cutting a hole for wires to pass through the double sided mounting tape)
• Once the wiring has been done, mount the fan unit onto the back mounting plate by sliding it onto the corresponding 6 key-slots and secure the fan with the two screws provided (Item 3).
• Ensure the L marking is on the bottom when mounting the fan.

Operation – Using the fan

• Keep the fan blades clear of any obstructions during operation.
  The fan MUST be locked in position before turning on.

Fan directional angle adjustment

• Adjust the fan and lock it in place by using the Locking Lever.

Timer Indicator LEDs:

• Timer Button
• Power Indicator LED (blue) – When the fan is ON, these two LEDs will be ON.

Items supplied in package

Unpacking the product

Carefully unpack the box and confirm that the following items are included:

• Equipment required for installation (Not included in package)
• Adjustable wrench (to assemble cables to bottom of unit)
• Phillips head screw driver
• 06 x 6 mm diameter mounting screws

Installation

Preparing back mounting plate

• a. Identify the intended mounting location for the fan.
• b. Insert the 2 stainless steel (Item 4) nuts into the nut recess holes on both sides of the back mounting plate.
• c. Peel backing off from double sided tape (Item 8) supplied, and stick it onto the back of the back mounting plate.

Mounting of back mounting plate

• a. Place the back mounting plate with the double sided tape facing towards the mounting location and stick the back mounting plate in place.
• b. Secure the back plate permanently at the intended location with 06 x 6 mm screws (not supplied) that is suitable for the wall at the mounting position.

Connecting the power cables

Electrical wiring

• a. Locate the two DC power terminals at the bottom of the fan unit marked (+) Positive and (-) Negative.
• b. Connect the supplied DC power cable pair (Item 5), onto the two terminals – with the DC power cable pair (Item 5), locking washers (Item 6) and brass nuts (Item 7) in the correct order as shown.
• c. Tighten all brass nuts on the two (+) Positive & (-) Negative terminals with a pliers or wrench. Do not tighten by hand ONLY.

Routing the cable and mounting

• d. There are three options to routing of the DC power cables, depending on how you are wiring the power cables.
• e. Once the wiring has been done, mount the fan unit onto the back mounting plate by sliding it onto the corresponding 6 key-slots & secure the fan with the two screws provided (Item 3).

Operation

Using the fan

Keep the fan blades clear of any obstructions during operation. The fan MUST be locked in position before turning on.

Fan directional angle adjustment

Safety

• The Fresca fan unit includes an over-current protection that protects the motor from short circuit.
• The Fresca fan unit includes a reverse polarity protection that protects the fan against any accidental reverse polarity.

Care & Maintenance

• The Fresca fan unit is designed for low maintenance.
• Turn off power to unit before any cleaning operations.
• The fan can be cleaned by wiping off accumulated dust or dirt with a dry cloth.
• Do not use cleaning solvent on any of the fan’s parts and surfaces.

User Warnings & Reminders

• Do not obstruct moving fan blades during operation.
• Do not use the fan outdoors (this fan is ONLY for indoor use).
• Do not use on wet surfaces or immerse in water.
• Do not place any objects close to the fan that may be sucked in or drawn onto the blades.
• Do not use near open fires, fireplace, stoves or any high heat source.
• Children must be supervised to ensure that they do not play with the fan.
• Do not use fan when any of the power cables to the fan is frayed or damaged.

Specification

Maximum Airflow:

• 140 CFM (Cubic Feet Per Minute)
  • 238 m3/h (Cubic Feet Per Hour)

www.onex.com.au

Limited Warranty

This product has a 2 year limited warranty from the date of purchase. The product you have purchased has been guaranteed by the manufacturer for the warranty period stated starting on the date of purchase against defects in workmanship and/or materials. This guarantee does not apply if the damage occurs because of accident, improper handling or operation, shipping damage, abuse, misuse, or unauthorized repairs made or attempted. Only parts that prove to be defective during the period of guarantee will be replaced without charge. When goods are sold in AU or NZ, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
In order to claim the warranty on a purchased product: This product is manufactured by Team Noble Limited, contact number +86 755 85278182 – Exclusive to One Email: inquires@1xproducts.com

Documents / Resources

| Fresca ORA-01 Fresca Fan [pdf] User Manual
ORA-01 Fresca Fan, ORA-01, Fresca Fan, Fan
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>