vatti G101RB LPG Tempered Glass Panel Table Gas Stove User Manual

June 4, 2024
vatti

vatti G101RB LPG Tempered Glass Panel Table Gas Stove

Thank you for choosing our gas stove. Please read this OWNER’S MANUAL carefully prior to use and keep it for further reference.

Instruction manual

Please read the instruction manual carefully before using and keep it for future reference and maintenance. This manual contains an important message, includes safe operation and special notes, structure diagram, main technical data, installation instruction, operation steps and adjustment ways, clean and maintenance, and troubleshooting.

Safe operation and special motes

  1. Check the gas type and pressure before using, making sure there was in accord with the marks in the label, where be stuck on the side of the stove, do not use it if the gas type and pressure is conflicting
  2. Keep the kitchen ventilates when using, there should have air entrance hole and an opening exhaust appliance. (Ventilate fan or range hood)
  3. There are forbidden to put flammable and explosive things around the stove.
  4. Do not touch the burner cap, trivet and surface plate, etc., When using or just flameout to avoid scalding.
  5. Shut off gas apply, open windows and doors to keep ventilation when gas leakage or strange smell is found, must not use any electric appliance or operate any electric switch to avoid an accident.
  6. If an accidental flameout happened when using, shut off the knob of the stove to avoid leakage.
  7. Adults should be presented when using( like the kitchen)
  8. For the sake of safe operation, to avoid leakage caused by aging, the hose should be changed per year.
  9. Shut off knob(s) of stove and valve of gas supply after using.

Main technical data

Name Model No. Nominal heat input Injector size
(kW) (mm)
Single burner gas stove Gl0lRBLPG 4.3 0.95/0.5
Gas type LPG
Gas pressure (Pa) 2800

Installation instruction

vatti-G101RB-LPG-Tempered-Glass-Panel-Table-Gas-Stove-
FIG-1

  1. After opening the carton, fix four legs on the four square yard as the diagram shows.
  2. Clean the labels, put the trivets on the correct positions.
  3. Check and adjust the burner cap and burner till match perfectly. As follow drawing shows:
  4. Take off the dustproof cap, put on the special gas hose to the position, where marked by the red line, then clamp the hose tightly by clip.
  5. Check leakage, turn the knob to the ” off ” position, put soap water on both connectors of gas hose, then open the gas valve, if there have air bubbles, you have to fix it again.
  6. The distance between the products put around and the stove should be more than 15cm, there should be more than 100cm space above the stove.
  7. The distance between the stove and cylinder should be around 1 m, the proper length of inlet gas hose is 1 m-2m. One side of the hose connects the cylinder, the other side connects the gas inlet hole of the stove, the hose can not contact the stove and thrill through the bottom of the stove, can not bend it forcedly.
  8. Both left and right burners of the stove can be used to heat convex bottom utensils or pans (cookers), the proper diameter of a convex bottom utensil is 32cm, the proper; diameter of pan is between 26-30cm,the weight of food should less than 10kg; the middle burner fits in with the pans with the diameter of 9-12cm, and the weight of food should be less than 1 kg. the cooker should be put even not deflected.
  9. It is recommended to install range hood above the stove.

Operation steps and adjustment

  1. Make sure all knobs on the “off” position, then open the main gas valve.
  2. Press the knob down by 3mm as the follow drawing shows, then turner it counter-clockwise until you hear ignition click, ignite the burner, then release the knob. {It may fail to ignite at the first time because of there is air in the hose, you have to repeat this procedure)
  3. Adjustment: the flame can be adjusted by turn the knobs slowly.( As drawing 3 shows)
  4. Flame out: turn the knobs clockwise to the “off” position as drawing 3 shows, the flame will be
    extinguished, then close the main gas valve.

Clean and maintenance

  1. Surface maintenance: wipe the surface by a dishcloth, with medium scour, then dry thoroughly with a dry cloth.
  2. Burner cap maintenance: in order to keep good burning condition, it is better to take the burner cap out and clean it by a brush ( or other tools) weekly, pay attention to the install the burner cap properly, as follow drawing shows:

Troubleshooting

vatti-G101RB-LPG-Tempered-Glass-Panel-Table-Gas-Stove-
FIG-5

Diagram

vatti-G101RB-LPG-Tempered-Glass-Panel-Table-Gas-Stove-
FIG-4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals