Roland KPD-70 Dedicated Pedal Board Instruction Manual
- June 13, 2024
- Roland
Table of Contents
Roland KPD-70 Dedicated Pedal Board Instruction Manual
Pedal board (-70KPD)
Installation hardware
-
x2
-
x2
-
x6
Installing the Pedal Board
-
Attach the installation hardware to the inside of the side boards.
-
Fasten the pedal board (KPD-70) to the stand as shown in the illustration.
-
Connect the cable of the pedal board to the Pedal 2 jack on the rear panel of the FP-30/FP-30X/FP-E50.
Make sure that the rubber feet on the bottom of the pedals are in contact with the floor
Before using this unit carefully read “USING THE UNIT SAFELY “and “IMPORTANT NOTES”.
USING THE UNIT SAFELY
INSTRUCTIONS FOR THE PREVENTION OF FIRE,ELECTRIC SHOCK,OR INJURY TO PERSONS
About A4WARNIG and CAUTION Notices
WARNING
Used for instructions intended to alert the user to the risk of death or
severe injury should the unit be used improperly
CAUTION
Used for instructions intended to alert the user to the risk of injury or
material damage should the unit be used improperly
*Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.
About he symbols
The symbol alerts the user to important instructions or warnings. The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.
The 
symbol alerts the user to items
that must never be carried out (are forbidden).The specific thing that must
not be done is indicated by the design contained within the circle. In the
case of the symbol at left, it means that the unit must never be disassembled.
The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power-cord plug must be unplugged from the outlet.
AOLLOWING THE OBSERVE A
WARNING
Do not disassemble or modify by
yourself Do not airy out anything unless you are instructed to do so in the
‘owner’s mana. Otherwise, you isk causing malfunction.
Do not repair or replace parts by yourself
Be sure to contact your dealer, a Roland service center, or an official Roland
dealer.
For a list of Roland service centers and official Roland dealers, refer to the Roland website.
Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat- generating equipment); or are
Damp (e.g., baths, washrooms, on wet floors); or are- Exposed to steam or smoke; or are
- Subject to salt exposure; or are
- Exposed to rain; or are Dusty or sandy; or are
- Subject to high levels of vibration and shakiness; or are
- Placed in a poorly ventilated location.
Use only the stand that is recommended
‘This unit should be used only with stand that is recommended by Roland.
Precautions regarding placement of this unit on ast and
Be sure to follow the instructions in the Owner’s Manual carefully when
placing this unit oak stand. Infits not setup properly, you risk creating an
unstable situation which may result n injurie.
Do not allow foreign objects or liquids to enter unit; never place containers
with liquid on unit
Do not place containers containing liquid (e.g., flower vases) on this
product. Never allow foreign objects (e.g., flammable objects, coins, wires)
or liquids (e.g., water or juice) to enter this product. Doing so may cause
short circuits, faulty operation, or other malfunctions
WARNING
Turn off the unit if an abnormality or
malfunction occurs In the following cases, immediately turn often power and
contact your dealer, a Roland service center, or an offal Roland dealer for
service.
- Objects have fallen into, or liquid has been spilled onto the unit; or
- If smoke or unusual odor occurs; or
- The unit has been exposed to rain (or otherwise has become wet); or
- The unit does not appear to operate normally or exhibits a marked change in performance.
For a list of Roland service centers and official Roland dealers, refer to the Roland website.
Be cautious to protect children from types of locations injury
Always make sure that an adult is on hand to provide supervision and
guidance when using the unit in places where children are present, or when a
child will be using the unit.
Do not drop or subject to strong impact
Otherwise, yourisk causing damage or malfunction.
CAUTION
Use only the specified stand(s)
This unit is designed to be used in combination with specific stands
(KSC-70/KSFE50) manufactured by Roland. If used in combination with other
stands, you risk sustaining injuries due to a lack of stability.
Route all power cords and cables
In such a way as to prevent them from getting entangled Injury could result if
someone were to trip on a cable and cause the unit to fall or topple.
Avoid climbing on top of the
unit, or placing heavy objects on it
Otherwise, you risk injury as the result of the unit toppling over or dropping
down.
Keep small items out of the reach of children
To prevent accidental ingestion of the parts listed below, always keep them
out of the reach of small children. •
Included Parts Screws
IMPORTANT NOTES
Placement
- Do not allow lighting devices that normally are used while their light source is very dose to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of time. Excessive heat can deform or discolor the unit. . When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition.
- Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
- Do not paste stickers, decals, or the like to this instrument. Peeling such matter off the instrument may damage the exterior finish.
- Do not place containers or anything else containing liquid on top of this unit. Also, whenever any liquid has been spilled on the surface of this unit, be sure to promptly wipe it away using a soft, dry cloth.
Maintenance
- To dean the unit, use dry, soft clothier one that is slightly dampened. Ty to wipe the entire surface using an equal amount of strength, moving the cloth along with the grain of the wood. Rubbing too hard in the same area can damage the finish.
- Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
- As with any wood-crafted product, some expansion and contraction of the wood can occur depending on the way the unit is used and the environment in which it is used. Over time, this can cause some of the screws to start coming loose. To ensure safe, worry-free use of the unit, you should periodically check the tightness of the screws shown in the illustration. If you find any that are loose, use a screwdriver to tighten them.
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Copyright © 2015 ROLAND CORPORATION
‘This symbol indicates that in EU countries, this product must be collected separately from household waste, as defined in cach region. Products bearing this symbol must not be discarded together with household waste.
For EU Countries
Manufacturer: Roland Corporation 2036-1 Nakagawa, Hosoe-cho, Kita-ku,
Hamamatsu, Shizuoka 431-1304, JAPAN
Importer: Roland Corporation
ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUM
For the .U.K
Manufacturer: Roland Corporation 2036-1 Nakagawa, Hosoe- cho, Kita-cu, Hamamatsu, Shizuoka 431-1304, JAPAN
Importer Roland Europe Group Limited Hive 2, 1530 Arlington Business
Park, Theale, Reading, Berkshire. RG7 4SA United Kingdom
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>