VEVOR B0CBSFJ6JP Level 2 EV Charger User Manual

PORTABLE ELECTRIC
CAR CHARGER
USER MANUAL

B0CBSFJ6JP Level 2 EV Charger

NEED HELP? CONTACT US!

Have product questions? Need technical support?
Please feel free to contact us:
855-385-1880
[email protected]

IMPORTANT:Be sure to review the contents of this manual before attempting to operate the equipment. This manual should be located where all machine users can easily reference it.

Dear Customer, Many thanks for choosing to purchase a Vevor product. Thanks toits technology, design and operation and the fact that it exceeds the strictest quality standards, a fully satisfactory use and long product life can be assured.
Please read this manual carefully to use the product correctly and safely. Before using this product please pay special attention to “safety advice and warnings”.
This product s intended for domestic use only. Please keep this manual safe for future use. Vevor will not accept any liability if the product s subject to improper use, or falure to comply with this guidance.

Applicable Vehicles

There are two different charging standards for EVs, Type 1 and Type 2. Please make sure you are choosing the correct charging plug for your EV.
TYPE 1: IEC 62196 Type 1, s a North American standard for electrical connectors for electric vehicles maintained by SAE International, Recommended SAE J1772.

Safety Advice and Warnings

• Read these instructions carefully before plugging in the charger and keep them for future reference. Failure to follow and observe these instructions could lead to an accident.
• Do not allow infants or children to play with packaging material. It may cause suffocation.
• Do not disassemble, repair or modify this product.
• This charger shall not be used by children. Keep the charger and its cord out of reach of children.
• This charger can be used by people with reduced physical, sensory or mental capabilites or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards  involved.
• This charger is not a toy. Children should be supervised to ensure that they do not play with the appliance.
• Ensure that the voltage indicated on the rating label matches the mains voltage before plugging in the charger
• Connect the charger to a socket that can supply a minimum of 16 amperes.
• The charger’s plug must fit into the mains socket properly. Do not alter the plug.
• Do not use the charger if the cable or plug is damaged. If any of the charger casings break, immediately disconnect the charger to prevent the possibility of an electric shock.
• Do not use the charger with damp hands or feet or barefooted.
• Do not use in inclement weather or immerse the portable charger in water.
• Do not force the power cord. Never use the power cord to lft up, carry or unplug the charger.
• Check the state of the power cord. Damaged or tangled cables increase the risk of electric shock.
• The temperature of the accessible surfaces may be high when the charger is in use.
  -Do not place the charger unit or its cables on or near high temperature items.
  -Do not leave this product in a closed unventilated environment while in use
  -The charger must be grounded.
  -The charger does not contain any user-serviceable parts.
  -Please do not disconnect the plugs while the EV charger is charging the vehicle.
  -Do not operate the charger in temperatures outside its operating range of -22°F t0 122°F(-30°C ~+ 50°0)

Portable EV Charger Components

Means of Indicator Light

LED Light 1
(Green)| LED Light 2
(Red)| Status
---|---|---
Blinking fastly| Off| Read to Connect to Vehicle
Blinking Slowly| Off| Charging
On| Off| Full Charged
Others| Others| See Troubleshooting

Charging Youe Vehicle

Use only on mains power with fault current circuit breaker.
Carefully read this guide together with your vehicle owner’s handbook prior to charging your electric vehicle.

1. Firmly insert the power plug into the outlet on the wall. Ensure the rated current of the outlet socket s not less than 16A (Figure 1).
2. Insert the Type 1 plug into the inlet on the electric vehicle (Figure2) .
3. The device starts charging automatically after the LED Light 1 begins to keep blinking regularly (Figure 3)

Stope Charging

1. Disconnect the Type 1 plug from the vehicle nlet. (Figure 4).
2. Disconnect the power plug from the outlet (Figure 5)
3. Replace the charger plug dust cap and store the charger unit in the bag provided, in a dry place (Figure 6).

Troubleshooting

LED Light 1 (Green)| LED Light 2 (Red)| Functions| Definition
---|---|---|---
Blinks once| Blinks once| Initial Status| Power on or reset. The relayis .off„.
Keeps blinking fastly| Lights off| To Be Connected| The voltage of Detection Point 1 is 12V, and the relay is “off”.
Keeps blinking slowly and regularly| lights off| Normal Charging| The voltage of Detection Point 1 is 6V, and the relay is “on”.
Lights on| Lights off| End of Charging| The voltage of Detection Point 1 is 9V, and the relay is “off”.
Lights off| Blinks once eve 2 every seconds| Abnormal Communication| The voltage of Detection Point 1 is abnormal (that is, the voltage value is not one of the following values: [6±0.8]V, (9±0.8)V, (12±0.8W), the  charger enters the protection status. When the voltage at Detection  Point 1 is back to normal, the charger will return to its normal working  state.
Lights off| Blinks twice every 2 seconds| Undervoltage| When the voltage is no more than 75V±10V for 0.1 second, the power output will be stopped. When the voltage rises to 90V±10V, the charging system will start again after a 5-second delay.
Lightsoff| Blinks 3 times every 2 seconds| ovenvolage| When the voltage s no lower than 270V+10V for 0.1 second, the power  output will be stoped.When th volage drops to 25410V, charging willstart againafter  5-second delay.”
Lightsoff| Blinks 4 times every 2 seconds| Leakage| When the leakage currentis 10 lower than 2545mA,the relay then will  off the response time is <100mS), When the ailure is – elininated,the  charger must be powered on again to continue charging.
Lightsoff| Blinks 5 times every 2 seconds| Overcurrent| 1. When the current s more than the “Stage’ Fised Overcurrent Value’  but no more than the “Stage? Fised Overcurrent Value or 5 seconds,  the relay wilbe off’; after 10 seconds,the relay will be on” again If this  overcurrent situation occurs again, the relay will e off” again,Afte 3  times of repets, the e ghtwi be on, and the charging is ver.
The charger must be re-powered on to continue charging. “2.When the  current is greater than the “Stage?
Fised Overcurrent Value’for 1 second,the elay will be “o’ the faiure light will be on, and charging will be over, It must be powered on  again to continue charging.”
Lightsoff| Blinks 6 times every 2 seconds| Power Plug/Circuit board Over-heat| When the temperature of the pover plug o cicut boardis mre than 85 for  2 econds, they wil be off must wait for the temperature to rop  below 65°C for 2 seconds to retun to normal working.
 | Lights on| PE wire is not connected to ground| Charging i allowed, but the warning ightwill be red” (no binking)al the  time.
Lightsoff| Blinks 8 times every 2 seconds| Power-on Self-test failed| Ifthe charger i faulty,the » P ey wilbe off and the charger will eport the  need for repair.

Technical Specification

voltage protection, leakage protection, and overheat protection integrated.
Certificate| CE / RoHS
Weight| 3.5 kg

Tel: 855-385-1880
E-mail: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>