genie WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD Bays User Guide

: June 13, 2024
: GENIE

Table of Contents

WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD Bays
Introduction
HDD Installation
Rear Panel Instruction
Start Up and Shut Down
Login
Configurations and Connections
Manual Recording and Playback
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD Bays

genie WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD
Bays 16 Channel H.265 Optimised
NVR with 2HDD Bays
WONVR216P5

Quick Start Guide
Please read these instructions carefully before operating the unit and keep for further reference.

Intro Section
Please read this instruction carefully before operating the product and keep it for further reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
This device should be operated only from the type of power source indicated on the marking label. The voltage of the power must be verified before use.
CAUTION:
Please check the device and the accessories after getting the device. If there are any damages, shortages or defects, please contact your dealer immediately.

Introduction

The Genie ‘Optimised’ WONVR216P5 network video recorder is a 16 channel PoE NVR with resolution on every channel of up to 5MP. There are 16 PoE ports available, 2 bays for hard drives and this versatile NVR fully supports up to 16 channels of simultaneous playback.
1.1 Product Features

Supports 16 channel 5MP, 4MP, 3MP, 1080p, 960p and 720p IP input
Adopt standard H.265 and H.264 high profile compression format to get high quality video at much lower bit rate
Intuitive and user friendly Graphic User Interface (GUI), Windows style operation by mouse
Multi-mode recording: Manual / Timer / Motion / Sensor
Search : Time slice, time, event (Manual, sensor, motion), Tag search
Express and flexible backup via USB, network etc.
Pentaplex : Preview, Record, Playback, Backup and Remote Access
DHCP, DDNS, PPPoE network protocol and CMS supported
Remote control via IE or CMS : Preview, playback, backup, PTZ and configuration
1080p HD output, true high resolution display
16 channel simultaneous playback
Authorisation management, log view and device status view
Multi-user online simultaneously
16 PoE network ports supported by IPC direct connection to NVR, supports PoE power supply
Support PTZ preset and auto cruise, up to 255 presets and 8 cruises
Support NAT function and QR code scanning by mobile phone and iPad
Powerful smart phone & iPad surveillance with iOS and Android OS

1.2 Product Dimensions

genie WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD Bays - Product
Dimensions 1.3 Specification

Model	WONVR216P5
System	OS
Video	Network Input
Network Access Format	5MP / 4MP / 3MP / 1080p / 960p / 720p @ 25 / 30fps
Output	HDMI x 1 : 1920 x 1080 / 1280 x 1024 / 1024 x 768

colours refer to different record events

HDD Installation

This series of the product supports 2 SATA hard drives. Please make sure that the device is powered off before the installation. The pictures of the installation are for reference only.

Loosen the screws to open the cover.
Place the HDD onto the bottom of the machine.
Put the HDDs onto the bottom of the device.
Connect the power and data cables.
Turn over the machine and secure the HDD with the screws.
Install back the cover and secure it with the screws.

Note: Please check the inside structure of the device and make sure that the cables are connected well before installing the cover back. Please format the HDD before using.

Rear Panel Instruction

The interfaces of the rear panel are for reference only. genie WONVR216P5 16
Channel H.265 Optimised NVR with 2HDD Bays - Rear Panel

Start Up and Shut Down

Startup

Connect the monitor and the power.
The device will boot and the power indicator will display blue.
A wizard window will pop up.

Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The device will shut down by clicking “OK” button. Then disconnect the power.

genie WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD Bays -
Login The default username is admin and the default password is 123456. You must configure the wizard if you start the NVR for the first time and you may change the password when you configure the wizard for the first time. You can skip the settings wizard next time. Click “Start” and select “Login”. This will take you to see a login box. Enter the default username and password you set. Then you will see the live image.

Configurations and Connections

6.1 Network Configuration & Adding IP Camera
After you finish adding IP cameras, you can see the live images through the monitor of the NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.
LAN

Set the network of the NVR. Go to Start → Settings → Network → TCP/IP. Enter IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the NVR and the router.
Go to Start → Settings → Network → Port. Enter HTTP port (the default value is 80), server port (the default port is 6036).
The internal ethernet port is the port which connects all the PoE ports with the NVR system. The PoE ports are available if the internal ethernet port is online. If it is offline, all the PoE ports will be unavailable. The IP address and subnet mask of the internal ethernet port can be changed to make the port in the same network segment with the IP cameras which directly connect to the PoE ports of the NVR.
Go to Start → Settings → Camera → Add Camera. The NVR will automatically refresh the cameras searched. The IPC which supports the Onvif protocol may be added manually. If the IPC searched is not in the same local network as the NVR, you should select the device and click to modify the IP address.
Checkmark the device you want to add and then click “Add” button. The NVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may
select the added device and click button to modify channel, IP address, etc.

WAN

Set the network of the NVR. Go to Start → Settings → Network → PPPoE. Enable PPPoE and then input the user name and password received from your ISP.
Go to Start → Settings → Camera. Click “Add Camera” or **** behind the column of the search camera and select “Manually Add” to add the IP cameras. Enter IP address, server port, username and password of the IP camera. The IP camera must be connected over WAN. And here the IP address of the IP camera must be a WAN IP address.

You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping.

Go to Start → Settings → Network → UPnP, and enable UPnP and then click “Apply” button to save.
Enable the UPnP function in the router.
Click “Refresh” button to refresh the UPnP status. If the UPnP status were still “Invalid UPnP” after refreshing it for several times, the port would be wrong. Please change the mapping type to “Manual” and then click to modify the port until the UPnP status turns to “valid UPnP”.

NAT Settings

The NVR shall be powered on and connected to the network.
Go to Start → Settings → Network → TCP/IP. You can obtain the IP address, subnet mask and gateway automatically. You can also manually enter them according to the actual network situation. Please make sure the network segment is the same as that of the network which is used.
Set the preferred or alternative DNS Server. Click “Apply” to save the parameters.
Go to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server Address (The default NAT Server Address is nat.autonat.com). Click “Apply” to save the parameters.

NAT Access
After finishing the NAT settings, you can enter www.autonat.com in the address bar of your browser and then press enter to go to the following interface. If you are the first time to access the NAT, you shall download and install the plug-in according to the tips. After installing the plug-in successfully, it will pop up the login box. genie WONVR216P5 16 Channel H.265 Optimised NVR
with 2HDD Bays - Login 1 Device Serial Number:
Click on the menu bar at the bottom of the live interface to check the serial number or go to Start → Settings → Network → Network Status to check the serial number of the NVR).
Username:
The username of the NVR. The default username is admin.
Password:
The password of the NVR. The password is set by yourself when you configure the wizard for the first time.

Manual Recording and Playback

9.1 Manual Recording
Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click to check the status of the recording. genie WONVR216P5 16 Channel H.265 Optimised NVR with 2HDD Bays -
Manual Recording

9.2 Playback
Instant Playback
Click “Instant Playback” in the right-click menu of the camera’s preview window to select or drag the playback progress bar to change the playback time to play back the record.
General Playback
Click on the tool bar at the bottom of the live preview interface or click Start → Playback to go to the playback interface as shown below. You can also add the playback cameras manually. Click in the playback window to pop up the “Add Camera” window. Check the cameras in the window and then click “Add” to add playback camera. The record files of the added playback camera will be played in the playback interface. genie WONVR216P5 16 Channel H.265 Optimised
NVR with 2HDD Bays - playback cameras