CREALITY LD-006 3D Printer User Manual

CREALITY LD-006 3D Printer

Dear Consumers,
Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you can also learn how to use the Printer in the following ways: View the accompanied instructions and videos in the U disk.
Visit our official website www.creality.com to find relevant software/hardware information, contact details and operation and maintenance instructions.

NOTES

1. Do not use the printer any way other than described herein in order to avoid personal injury or property damage.

2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.

3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.

4. Please use recommended resin to in case damage of machine.

5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.

6. Please do not open the plastic cover during usage, otherwise the printing will be interrupted.

7. Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily
   injury, or printer damage.

8. Please wait a moment after the print is finished. And please wear gloves to take out the model by tools.

9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other
   material off the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.

10. Children under 10 years should not use the printer without supervision.

11. Tips：Do not plug or unplug the power cord when power on.

12. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators’ legal liability under any circustance.

Equipment Introduction

1. Leveling screw
2. Buliding platform
3. Thumb screw
4. Resin vat
5. Touch screen
6. Limit sensor conductor
7. Air filter
8. Power switch
9. Power socket
10. USB port

Equipment Parameters

Basic Parameters

Model| LD-006
Software language| English
Print method| U disk
X/Y-axis resolution| 38402400 | 50μm
Z-axis precision| 0.01mm-0.1mm(layer thickness
Print speed| 1-4S/ layer
Special filaments| CHoigmhmtoounghringeidssp,hDoetnotsaelnmsiotidvelrreessiinn,.Standard resin, High elasticity, High hardness,
Light source configuration| UV integrated lamp bead (wavelength 405nm)
Operation system| Windows XP and above systems | Windows XP
Nominal power| 250W
Print size| 192120250mm (lengthwidth height) | 192120250mm
Machine size| 325290500mm
Package size| 430400*600mm
Machine weight| 13.5KG
Gross weight| 17.5KG
Display screen| 4.3inch

Package Content

Tips: the above accessories are for reference only, in kind prevail!

Assemble the 3D Printer

Note: Put the plastic cover on the machine body and the installation is completed.

Interface Information

Tools

Note: The UI information is only for reference, the actual UI may be different.

Interface Information

**System

**

Note: The UI information is only for reference, the actual UI may be different.

**Print

**

Note: The UI information is only for reference, the actual UI may be different.

Level Platform 1

1. First raise the platform, then loosen rubber screws on the left and right sides of the resin vat, and take out the resin vat.
2. Place the calibracation card on the printing screen， go “ Tools → Manual → Home”with the touch screen, and check whether the platform sticks into thecalibration card evenly.
   Note: The printing platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.

Level Platform 2

If the platform does not stick to the print screen, do as the following:

1. After unscrewing the leveling screws, press“Home” to keep the platform and the print screen parallel.
2. Gently press the platform and tighten 4 screws clockwise, and the platform can be leveled successfully.
3. Move up the z-axis to a proper position, remove the calibration card and install the resin vat back, and then tighten the fixing screws at both ends of the resin vat.

Load Resin

Pour the UV photosensitive resin into the resin vat. The slot capacity is 500ml/1000ml.

Note: Please pay attention to the orientation marks and keep the printing platform assembled in the right direction. Otherwise it may lead to leveling faliure!
Tips： How to change resin:
Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin, and then install the resin vat to the machine.
Caution: Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin.

Release Film Instructions

Installation steps

• First, remove the 14 screws at the bottom of the vat and take down the old release film.
• Prepare the new release film, peel off the the protective films on both sides of the release film. Align the holes and fit the release film on the clamping ring.
• Finally, place the film-ring assembly back into the vat frame gently, then intall and tighten the fixing screws diagonally.
• The installed release film is as shown.

Start Printing

Slice

1. Open the slice software of LCD 3D printer, click “open” on the left of the screen and add model file.
2. If the model needs to add support, click the upper right icon to set corresponding parameters.
3. Click icon ①→click ②“Setting”→setting slice parameters ( recommend to set parameters of bottom layer as 5-20).
4. Click “Slice”→waiting for slice to be finished→save the sliced file( You are welcome to find more details of slicing tutorial on the official website www.creality.com).

Print

1. Generate CTB file，and save the file to U disk.
2. Insert the U disk → press the print button.
3. Press “up” or “down” to select files.
4. Select the file to be printed and press “print”.
5. Printing.

Wiring Connection

Troubleshooting

Due to the differences between different machine models, the physical objects and the final images can differ.The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.
Official Website: www.creality.com
Tel：+86 755-8523 4565
E-mail: info@creality.com
cs@creality.com

References

• 创想三维(CREALITY) - 3D打印机,教育/工业3D打印机领导品牌
• Reality Simulations, Inc.
• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
• 创想三维(CREALITY) - 3D打印机,教育/工业3D打印机领导品牌

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>