FIAMMA CB Frame Crafter 3 Carry Bike VW Crafter H3 Frame Instruction Manual
- June 13, 2024
- FIAMMA
Table of Contents
Bicycles carrier
Installation and usage instructions
CARRY-BIKE
FRAME CRAFTER 3 BIKES
02094-37A
02094A37A
VW CRAFTER
CARRY-BIKE
Check that nothing has been damaged or deformed during transport.
In the event of doubts or questions concerning the installation, use or
limitations of the product, contact the dealer. We recommend that the
installation is carried out by qualifi ed personnel and in compliance with
current local regulations.
Installation only on right rear door
Not suitable for vehicles with 270° hinge system
Tighten the screws and ensuring that the rear door opens and closes correctly
WARNING!
Do not fully tighten the fork to the tube, leave 2mm space.
In case of problems please contact your local dealer indicating the data on the nameplate. Consult our website for spare parts drawing.
Read the following instructions and warnings carefully; failure to observe
these installation and usage instructions as well as the laws for driving in
the relevant country may cause severe harm or damage for which the
manufacturer declines all responsibility. Before installation, ensure
compatibility with the vehicle on which the product must be installed.
Checking that the wall/rear door is suffi ciently solid and suitable for
guaranteeing the resistance of the anchoring points is always mandatory. If
not, strength and compliance with the maximum load indicated in the
instructions are not guaranteed and it will be necessary to reinforce these
points.
After having positioned the Carry-Bike on the rear axle of the vehicle, the
normal weight distribution on both axles would be modifi ed. This variation
must not exceed the maximum permissible axle load.
Never exceed the maximum permitted length and the total weight of the full-
load vehicle.
Make sure that loading occurs following a correct weight distribution; it must
be uniformly distributed (the heaviest bike must be placed near the wall of
the vehicle) to ensure better stability.
Always give warnings about the presence of the Carry-Bike on your vehicle,
using a clearly signal for leaning loads and, in case of limited rear
visibiliy, use the additional rear-view mirrors.
Take into account the presence of the Carry-Bike, paying attention during
driving and expecially during reversing manoeuvres, particularly if you have
parking assist system.
Always comply with speed limits and the Highway Code.
The speed should always be suitable to traffi c conditions and towed load.
In case of use of the bike carrier with tow make sure that the tow hook is
always accessible and the corner mobility of the tow is guaranteed (volume
measuring din 74058).
Check periodically the bicycle rack to make sure it is fi rmly attached,
especially during the fi rst kilometers of after long trips to avoid damages of
the Carry-Bike/vehicle. Make sure the belts are not loose and that the holding
brackets have not shifted. Replace worn components immediately.
During Carry-Bike installation, verify that there is enough distance between
handlebars and/or pedals and the vehicle’s rear windows in order to avoid any
damages of the window van; do not leave accessories attached (bay seats,
baskets, etc) because vibrations could disengage bikes. In some cases, the
rear windscreen wiper may not work due to the presence of bicycles. Be aware
of the brush radius before operating the windscreen wiper.
On this type of Carry-Bike, bike covers are not allowed (Bike Cover).
In the version with intermediate and lowered rail support position, the use of
the licence plate carrier bar with lights is required.
Rear door opens even with bikes mounted.
It is recommended to rotate the handlebars of bicycles to avoid damage to the
vehicle wall, for which Fiamma declines all responsibility.
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.
fiamma.com
Fiamma S.p.A. – Italy
Via San Rocco, 56
21010 Cardano al Campo (VA)
All rights reserved.
Fiamma S.p.A. reserves the right to modify at any time, without notice,
prices, materials, specifi cations and models or to cease production of any
model.
M0_IS_98690M168_revA