ADD OFFROAD 23+ Ford Bronco Raptor Rock Fighter Rear Bumper Installation Guide

ADD OFFROAD 23+ Ford Bronco Raptor Rock Fighter Rear Bumper

Preparation

We recommend reading through the installation instructions in whole before performing the work.

• Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.
• When button head bolts are being used, install the supplied washer on the nut side. Then, hold the bolt stationary and only turn the nut to tighten. Do not turn the bolt to tighten hardware assembly, unless otherwise noted.
• Anti-seize is recommended for all fasteners.

SKILL LEVEL

-Easy/Intermediate
**This installation requires 2 people for best results

TIME REQUIRED

– 2 hours for OEM Removal/Bumper Install
-1 Additional Hour to Wire Cube Lights
Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will result in a greater labor charge.

INCLUDED IN KIT

2- Hex Head Bolts (3/4-10 X 1 1/2”)
2- Nylon Lock Nuts (3/4-10”)
4- Flat Washers (3/4”)
2- Nylon Lock Nuts (1/2-13”)
2- Button Head Bolts (1/2-13 X 1 1/2”)
2- Flat Washer (1/2”)
4- Hex Head Bolts (3/8-16 x 1 1/4”)
4- Flat Washers (3/8”)

TOOLS REQUIRED

(Sockets) 9/16, 3/4, 1-1/16, 1-1/8, 13mm, 18mm
(Box end wrenches) 9/16, 3/4, 1-1/16, 1-1/8, 13mm, 18mm (Allen wrenches) 5/16
Fastener remover or flathead screwdriver
Zip ties
Ratchet
Flat File

Removal

ROCK FIGHTER REAR BUMPER
23+/FORD BRONCO RAPTOR

STEP 1
Disconnect the wire harness on both the driver and passenger sides.

STEP 2
Remove the tow hooks using a (18mm socket). You can keep the bolts and tow hooks for later on in the install

STEP 3
Using a (13mm socket) remove the mounting bolts. You can now fully remove the bumper.

STEP 4
Remove the middle metal cover using a (13mm socket) to expose the wire harness and sensors.

STEP 5
Remove the sensors from the bezels by spreading the tabs. Spread carefully

STEP 6
Disconnect the license plate light by pushing down on the tab and pulling.

STEP 7
Repeat step 5 to remove the sensor. Remember the orientation for this will be important in step 10

STEP 8
Install the supplied mounting brackets using the stock hardware removed from step 2. Then install the provided 3/4” bolts, washers, and nylon lock nuts using a (1-1/8 socket) and a (1-1/16 wrench).

STEP 9
Install the sensor bezels into the ADD bumper. Ensure they are in the same orientation as OEM. *If the bezels do not click into place you may have to trim the tabs to match the thickness of the bumper as shown below

STEP 10
For the outer sensor bezels, trim the tabs on the backer by using a (flat file) and install the sensor bezels in the same orientation as OEM. Now you can install the wire harness and push the sensors into the bezels.

STEP 11
Trim the tabs by using a (flat file) as shown below on the license plate light and install on your ADD bumper.

STEP 12
Install the provided nut clips in the slots on both mounting plates as shown below.

STEP 13
Route the wire harness plug-in through the slot on the mount plate as shown below. (Repeat on other side).

STEP 14
You can now install the bumper with the 2x 1/2” button head bolts, washers, and nylon lock nuts using a (5/16 allen wrench) and (3/4 wrench). and also install the 4x provided 3/8” hex head bolts, and washers using a (9/16 socket/wrench).

STEP 15
Plug in the wire harness on both the driver and passenger sides.

final

STEP 1
Stand back and enjoy your new ADD Rock Fighter™ rear bumper.
Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter.

Customer Service

This product is protected by one or more U.S. patents
www.addictivedesertdesigns.com/patents
For Additional Support or Technical Questions,
Please Call480-671-0820 or
Email Info@AddictiveDesertDesigns.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>