ADD OFFROAD AC2302201NA Ford Bronco Center Console Installation Guide
- June 13, 2024
- ADD OFFROAD
Table of Contents
ADD OFFROAD AC2302201NA Ford Bronco Center Console
Product Information
Installation Guide
- Product Name: Center Console
- Compatible Vehicle: 21+/Ford Bronco
- Product Code: AC2302201NA
Tools Required:
- Allen wrenches (1/8, 5/32)
- Drill bit (15/64)
- Rivet tool
- Marker
- Drill
Skill Level: Easy/Intermediate
Time Required: 1 hour
Included in Kit:
- 8 Button Head Bolts (1/4-20 X 1/2)
- 8 Rivet Nut (1/4-20 Large Flange 0.165)
- 8 Flat Washer (M6)
- 4 Button Head Bolt (10-24 X 3/8)
Warnings/Cautions Before Starting Installation:
- Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide.
- Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of the vehicle if required for installation of this product.
- This installation may require some technical skills and knowledge of basic mechanical work. If you do not feel capable of performing this install, please take this product to a trained professional.
- After reading this guide, please contact us with any questions or concerns before installing the product. Customer Service: 480-671-0820
- Addictive Desert Designs is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.
- Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components.
- We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle.
- Inspect all contents of this package to make sure the product is not damaged and all installation hardware has been included. If parts are missing from the kit, please be prepared to provide the following information:
- Name of purchase location
- Bar Code on side of box
- Date above bar code
- Date inside box cover
- ALWAYS WEAR EYE PROTECTION WHEN OPERATING POWER TOOLS
Product Usage Instructions
Step 1
Install the ADD logo using the provided 10-24 x 3/8 Stainless steel Button
Head Bolts using a (1/8 Allen Head).
Step 2
Hold up the panels with your hand and with the other, mark out your holes with
a marker.
Step 3
Drill the marked holes from step 2 by using a (15/64 drill bit). Do not drill
into the panel more than 1/4 due to the components inside the center console.
Step 4
Using a Rivet Nut Tool, install the provided 1/4-20 Rivet nuts in the holes
drilled in step 3.
Tech Tip: If you do not have a rivet nut tool, use a 1/4-20 x 3/4 hex head bolt, a 1/4 washer, and a 3/8 nut to install the rivet nuts. Tighten using a (9/16 wrench) and a (7/16 socket) on an impact. HARDWARE NOT INCLUDED
Step 5
Install the molle panels on both sides with the provided 1/4-20 Button Head
Bolt and M6 washers using a (5/32 Hex).
21+/FORD BRONCO
CENTER CONSOLE
AC2302201NA
TOOLS REQUIRED
(Allen wrenches) 1/8, 5/32 (Drill bit) 15/64
Rivet tool
Marker
Drill
TIME REQUIRED – 1 hours
SKILL LEVEL – Easy/Intermediate
INCLUDED IN KIT
- 8- Button Head Bolts (1/4-20 X 1/2)
- 8- Rivet Nut (1/4-20 Large Flange 0.165”)
- 8- Flat Washer (M6)
- 4- Button Head Bolt (10-24 X 3/8)
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
BEFORE YOU INSTALL THIS KIT-
Read and understand all instructions, warnings, cautions, & notes contained in
this installation instruction guide. Consult your vehicle owner’s manual for
proper disconnection of electrical and lifting of vehicle if required for
installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing this
install please take this product to a trained professional.
After reading this guide please contact us with any questions or concerns
before installing product.
Customer Service 480-671-0820
Addictive desert designs is not responsible for any bodily injury or harm to
you or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory recommended
procedures for removal and installation of original equipment components.
We recommend that the factory shop manual and any special tools needed to
service your vehicle be on hand during the installation. Installation of this
kit without proper knowledge of the factory recommended procedures may affect
the performance of these components and the safety of the vehicle.
Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information:
-
Name of purchase location
-
Bar Code on side of box
-
Date above bar code
-
Date inside box cover
-
ALWAYS WEAR EYE PROTECTION WHEN OPERATING POWER TOOLS*
INSTALLATION guide
CENTER CONSOLE 21+/FORD BRONCO
STEP 1
Install the ADD logo using the provided 10-24 x 3/8” Stainless steel Button
Head Bolts using a (1/8 Allen Head).
STEP 2
Hold up the panels with your hand and with the other, mark out your holes with
a marker.
STEP 3
Drill the marked holes from step 2 by using a (15/64 drill bit). (Do not drill
into the panel more than a 1/4” due to the components inside the center
console)
STEP 4
Using a (Rivet Nut Tool) install the provided 1/4-20 Rivet nuts in the holes
drilled in step 3.
TECH TIP
If you do not have a rivet nut tool, use a 1/4-20 x 3/4 hex head bolt, a 1/4
washer, and a 3/8 nut to install the rivet nuts. Tighten using a (9/16 wrench)
and a (7/16 socket) on a impact.
HARDWARE NOT INCLUDED
STEP 5
Install the molle panels on both sides with the provided 1/4-20 Button Head
Bolt and M6 washers using a (5/32 Hex).
STEP 6
Stand back and enjoy your new ADD Center Console.
Check and re-tighten, if needed, all mounting bolts after 100 miles and
periodically thereafter.
This product is protected by one or more U.S. patents
www.addictivedesertdesigns.com/patents
For Additional Support or Technical Questions, Please Call
480-671-0820 or
Email
[email protected]