elna eXpressive 900 Oval Hat Hoop Instructions

: June 13, 2024
: Elna

Table of Contents

elna eXpressive 900 Oval Hat Hoop
Product Information
Product Usage Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elna eXpressive 900 Oval Hat Hoop

elna -eXpressive -900 -Oval -Hat -Hoop -product image

Product Information

The Oval Hat Hoop is compatible with the eXpressive 900 / 920 embroidery machines and fits the SQ14 hoop. It is designed for embroidering on hats and caps.

The hat hoop kit includes:

Oval Hat Hoop Insert
Clamping knobs
1 Hat Hoop Base Plate
1 Hat Hoop Clamping Plate
2 Clamping Knobs
Instructions

Additional supplies needed:

Adhesive stabilizer
Tape or staples
Appropriate Hoop
Stapler
Tape

Product Usage Instructions

Hat Hoop Insert Preparation:

Remove the inner hoop from the embroidery machine.
Position the Hat Hoop Insert within the hoop.
Tighten the hoop screw. As the hoop is tightened, arrows on the hoop insert should align with the notches on the sides of the hoop. If the arrows do not line up when the hoops is tightened, loosen the outer hoop and adjust the position of the insert as needed. Alignment of the arrows indicate that the Hat Hoop Insert is correctly inserted.
Raising the presser foot lever to its highest position, attach the hoop insert to the embroider arm. Select the desired design and determine where the design will be stitched on the hat. Note: Only use designs that are designed that are approximately 5” x 4.3”. Selecting a larger design will cause the embroider foot to hit the insert and could cause damage to the insert or to your sewing machine. Use the Tracing function and the placement arrows to verify that the design will stitch within the open area of the Hoop Insert.
After verifying that the entire embroidery design will stitch with in the open area of the hat insert, disconnect the hoop from the embroidery arm, raise the presser foot and remove the hoops from the machine.
Hat Preparation:
To prepare the cap for embroidery, unfasten any snaps, clasps, or straps. Turn the hat upside down and staple (or tape) the headband to the bill/visor.
Cut an 8 x 8 square of adhesive stabilizer. Remove the paper backing. Carefully attach the sticky side of the stabilizer to the back of the hoop insert, starting from one side. Pull the stabilizer across the opening and firmly press the edges to the hoop insert. Adjust if needed. Attaching the Cap to the Hoop Insert:
Loosen the clamping knobs by turning them counterclockwise. Place the cap on the hoop insert, right side up. Lift the clamping plate and slide the bill/visor of the cap underneath until it rests against the clamping screw posts. Align the centerline of the clamping plate with the center seam of the cap. If there is no seam, align with the center of the cap. Tighten the clamping knobs without over-tightening.
Pull the lower back edge of the cap toward the back of the hoop insert base plate, aligning the center back seam with the V-groove (center line). Secure the center seam of the hat to the stabilizer using finger pressure. Adhere the rest of the cap to the stabilizer, working from the center out. Tape the excess hat fabric to the outer edges of the hoop.
Embroidery Process:
Slide the hoop onto the bed of the embroider machine, from the left side; making sure the needle is in the highest position. Attach the hoop to the embroidery arm. Make sure the needle is aligned with the center of the hat. If necessary, reposition the hoop using the placement arrows on the Ready To Sew screen. When the design is centered, embroider the design.
Completing Embroidery:
When the embroidery is complete, disconnect the hoop from the embroidery arm. Raise the embroidery foot to its highest position. Carefully remove the hoop from the machine, sliding the hoop toward the left side of the machine. Loosen the clamping plate. Remove the hat from the hoop insert. Carefully remove the staples, tape and excess stabilizer from the cap. Clip the threads.