VENT 50 Skylight Fiamma Vent Crystal for Van Camper Instruction Manual
- June 13, 2024
- FIAMMA
Table of Contents
VENT 50 Skylight Fiamma Vent Crystal for Van Camper
PACKAGE CONTENTS
TOOLS NEEDED
|
---|---
Vent 50 White| 01668-01-| 4,5 kg
01668-02-
Vent 50 Crystal| 01688-01D| 4,7 kg
01688-02D
DIMENSIONS
Check that nothing has been damaged or deformed during transport.
In the event of doubts or questions concerning the installation, use or
limitations of the product, contact the dealer. We recommend that the
installation is carried out by qualified personnel and in compliance with
current local regulations.
INSTALLATION INSTRUCTIONS
- Decide where the rooflight should be installed and make a square hole of 50cm. The rooflight can be installed on roofs with thickness between 30 and 70mm. For thickness lower than 30mm set a suitable frame to be positioned on the roof inside the vehicle between the roof and the inside frame.
- Remove the inside frame and spread waterproof sealant over greater part of the bottom of the outside frame to a minimum thickness of 3mm. Recommended sealant: SIKALASTOMER-710 / THERMOSTAT II / DEKALIN 1512.
- Clean the bearing surface on the roof, put the outside part of the rooflight on the roof, insert the inside frame in the provided square hole and from inside the vehicle screw the two frames together with 12 ø4,8mm UNI EN ISO 7049 wood screws. To fi x with security the rooflight external part, the screw must be tightened at least 15mm.
- Apply sealant to the whole perimeter of the outer frame and fill any gaps between the frame and the roof. Finally insert the inside frame with the mosquito net and the blind and fit them with screws ø3,5x15mm UNI EN ISO 7049.
Remove the protective plastic applied to the cover (do not expose the product
to sunlight for too long to avoid to make this operation difficult).
SAFETY INSTRUCTIONS
In case of problems please contact your local dealer indicating the data on
the nameplate. Consult our website for spare parts drawing.
Fiamma declines all responsibility for any personal injury and damage to
property due to incorrect assembly or use of the product; it is suggested to
keep the instructions inside the vehicle.
The assembly of the product must be carried out according to the assembly
instructions: the product must not be modifi ed in any way.
Before proceeding with assembly, check that the roof thickness is compatible
with the product. Before choosing the place where to assembly the rooflight,
check that:
- the product doesn’t interfere with adjacent accessories (luggage racks, cables, reinforcements in the roof, cabinets inside the passenger compartment).
- the internal and external surface of the roof is flat.
Periodically check the tightness of all the screws in the rooflight, especially after the fi rst kilometres from the installation and always before and after long trips. If the opening-closing device hardens, lubricate the lid opening device with a few drops of grease. It is forbidden to walk on the product cover. Before starting the vehicle, check that the rooflight is properly closed. Periodically check that the cover is intact. Don’t open the rooflight when the vehicle is travelling. Don’t open the rooflight in case of strong wind or rain. Remove snow or ice from the rooflight. Always comply with speed limits and the Highway Code. The speed should always be suitable to traffic conditions and transported load.
CARE AND MAINTENANCE:
For the internal and external cleaning of the rooflight, always use only
neutral, non-aggressive detergents. For cleaning the Crystal cover use an
acrylic glass cleaner with a soft cloth so as not to scratch the surface.
Never use aggressive products such as glass cleaners, all-purpose cleaners,
abrasives or dish-washing detergents. Also, never use alcohol-containing
detergents, solvents or any corrosive liquid. Clean the mosquito net with
water and neutral detergent removing the roller blind and the four fastening
screws.
Accessories
SPOILER UNIVERSAL
Item No. 06289-01-
TURBO-KIT
Item No. 98683-059
Warranty
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.
Fiamma S.p.A. – Italy Via San Rocco, 56 21010 Cardano al Campo (VA) All rights
reserved.
Fiamma S.p.A.
reserves the right to modify at any time, without notice, prices, materials,
specifications and models or to cease production of any model.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>