SKIP HOP 9P012710-01 3-in-1 Ride On Toy Owner’s Manual

SKIP HOP 9P012710-01 3-in-1 Ride On Toy

Product Information

standards.

Product Usage Instructions

Stage 1: Wagon Mode

1. Insert the front wheels with the locator in the FRONT. Check the window to ensure the metal button is visible on the RIGHT side.
2. 1. Insert the handle with the Horn/Light Button facing FRONT. Press in the lower button while pushing the handle down until it clicks.
3. Press a screwdriver into the RIGHT adjuster hole and push down the handle until it won’t go any further.
4. Press in the upper button while pushing the handle down until it clicks.
5. Flip the seat upside down and press the side buttons to assemble the seat to the base.

Stage 2: Ride On Mode

1. Remove the handle by pressing a screwdriver into the RIGHT adjuster hole while pulling the handle all the way out.
2. Remove the front wheels by pressing the metal button in the window and pulling the wheels all the way out.
3. Re-insert the front wheels with the locator in the BACK. Check the window to ensure the metal button is visible on the LEFT side.
4. 1. Insert the handle with the Horn/Light Button facing the BACK. Press in the lower button while pushing the handle down until it clicks.
5. Press a screwdriver into the LEFT adjuster hole and push down the handle until it won’t go any further.
6. Press in the upper button while pushing the handle down until it clicks.
7. Remove the seat, flip it over, and re-attach it to the base while pressing in the buttons.

Assembly: Scooter Mode
Adult assembly is required for this mode.

1. Remove the seat while pressing the release buttons.

Battery Replacement
Adult supervision is required for battery replacement.

1. Loosen the battery door screw using a Philips head screwdriver.
2. Open the battery door compartment and insert three new AAA (1.5V) Alkaline batteries, ensuring correct polarity.
3. Position the battery door securely back into place and tighten with a screwdriver. *Batteries should be replaced by an adult.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING:
Read all instructions and warnings before assembly and use of 3-in-1 ride-on. Spot clean only. Do not submerge in water.

Read all instructions and warnings before assembly and use of 3-in-1 ride-on.

CONTENTS

CLEANING AND CARE

Spot clean only. Do not submerge in water.

WAGON MODE

1. Insert front wheels with the “locator” in the FRONT. Check the window to make sure the metal button is visible on the RIGHT side.
2. 2A. Insert handle with the Horn/Light Button facing FRONT. Press in lower button while pushing handle down until it clicks.
3. 2B. Press screwdriver into RIGHT adjuster hole and push down handle until it won’t go any further.
4. 2C. Press in upper button while pushing handle down until it clicks.
5. Flip seat upside down and press side buttons to assemble seat to base.

RIDE ON MODE

1. Remove handle by pressing screwdriver into RIGHT adjuster hole while pulling the handle all the way out.
2. Remove front wheels by pressing metal button in the window and pulling the wheels all the way out.
3. Re-insert front wheels with the “locator” in the BACK. Check the window to make sure the metal button is visible on the LEFT side.
4. 4A. Insert handle with the Horn/Light Button facing the BACK. Press in lower button while pushing handle down until it clicks.
5. 4B. Press screwdriver into LEFT adjuster hole and push down handle until it won’t go any further.
6. 4C. Press in upper button while pushing handle down until it clicks.
7. 4C. Press in upper button while pushing handle down until it clicks.

ASSEMBLY

SCOOTER MODE

1. Remove seat while pressing release buttons.
2. Raise handle by pressing screwdriver into LEFT adjuster hole and pulling to release the upper button. Release the screwdriver and pull until the lower button clicks into place.

TO REPLACE BATTERIES

1. Loosen the battery door screw using a Philips head screwdriver.
2. Open battery door compartment and insert three new AAA (1.5V) Alkaline batteries. Be sure to insert with correct polarity.
3. Position the battery door securely back into place and tighten with a screwdriver. *Batteries should be replaced by an adult.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

BATTERY INFORMATION

At the end of product life, remove batteries from product by following the battery replacement instructions. Always dispose of used batteries properly. See section on safety and disposal information.

• Batteries are to be inserted with the correct polarity.
• Do not burn batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are only to be charged under adult supervision.
• Rechargeable batteries are to be removed from the toy before being charged.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Different types of batteries or new and used batteries are not to be mixed.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

WARNING
Adult assembly required. To reduce the risk of injury, adult supervision is required. The toy should be used with caution as skill is required in order to avoid falls or collisions, causing injury to the user or third parties. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than 1 rider. Not for children with a body weight of 44lb (20kg) or more. This toy has no brake. Protective equipment should be worn such as a helmet, gloves, knee-pads and elbow- pads. Not to be used in traffic or public highways. Only use the battery(ies) specified by the manufacturer.

© Skip Hop, Inc.
SKIP HOP and MUST-HAVES MADE BETTER are trademarks owned by Skip Hop, Inc.

All rights reserved.

• 100 W 33 ST, STE 1125, NY, NY 10001
• In the US: 888.782.9548
• US warranty: www.skiphop.com.

Meets or exceeds ASTM F963 and applicable safety standards.

• The PBS KIDS logo is a registered mark of PBS and is used with permission.

© 2022 The Fred Rogers Company All Rights Reserved.

References

• skiphop.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>