GATEXPERT CN Series Garage Door Opener Installation Guide

GATEXPERT CN Series Garage Door Opener

Product Information:
MEN-003-N Garage Door Opener

Model: MEN-003-N

Product Type: Garage Door Opener
Installation Manual: CN Series
Manufacturer: GatExpert Store
Website: www.gatexpertstore.com

Email: sales@gatexpertstore.com

Attention to Security:

• To ensure your safety, reduce accidents happens, before installation please must read the installation manual carefully, and operation is strictly complying with the installation manual.
• If you have some questions, please ask the specialists and the dealers.

Technical Parameter:

• Rated Voltage: Open and close force
• Motor: Transmission frequency
• Decoding: Transmitter
• Standby Power:
• Work Temperature:
• Courtesy Light:
• Rated Operation Time:

Tools Needed:

• During assembly, installation, and adjustment of the opener, instructions will call for hand tools.

Product Usage Instructions

Installation Precautions

• The installation worker must inspect the door before installation, only allows installation of the opener at balance state. Otherwise, it could have serious consequences.
• When the door is running, no people and objects can cross or stay below the door.
• It is forbidden to use the remote control when you cannot see the door running to avoid accidents and misuse of the garage door opening.
• The mechanical limiters should be added to the doors on both sides to prevent the body from sliding off the door. Note: If you do not have a side door, please install a blackout unlocking device so as to open the door by hand during a blackout.

Garage Door Opener Installation

Install the Header Bracket and the Door Bracket
Refer to the illustrations below (G4, G3, H1, H8) to install the header bracket and the door bracket.

Attach the Rail to the Header Bracket
Refer to the illustrations below (H7, H5) to attach the rail to= the header bracket.

Door Arm Connection

1. Close the door and disconnect the trolley by pulling the emergency release handle.
2. Attach the straight door arm to the outer trolley using the shouldered shaft, short (H6). Attach with the cotter pin (H5).
3. Attach the curved door arm to the door bracket using the shouldered shaft, short (H6). Attach with the cotter pin (H5).
4. Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity and attach using the bolts (H4) and nuts (H3).
5. Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal. The trolley will re-engage automatically when the garage door opener is activated.

Control Box Overview

Refer to the illustrations below to understand the control box and its functions.

Basic Function Settings

Adjusting the Open and Close Limits:

1. Press the ‘ST’ button and hold on until the LED displays ‘1’.

2. Press and hold the ‘OP’ button until the door reaches the
   desired open position. Fine adjustments can be made by toggling OP & CL buttons.

3. Press the ‘ST’ button. The LED displays ‘2’.

4. Press and hold the ‘CL’ button until the door reaches the desired close position. For fine adjustments, toggle OP & CL buttons.

5. Press the ‘ST’ button to confirm the close position. The door is now set for normal operation.

Programming Hand Transmitters

Note: Hand transmitters that are supplied with the door opener are pre- programmed.

No further instructions or steps are provided in the given text-extract for programming hand transmitters.
Please refer to the complete installation manual for detailed instructions and further information.

Attention to security
To ensure your safety, reduce accidents happens, before installation please must read the installation manual carefully, and operation is strictly complying with the installation manual. If you have some questions, please ask the specialists and the dealers.

1. The installation worker must inspect the door before installation, only allows installation the opener at balance state, Otherwise it could have serious consequences.
2. When the door is running, no people and object can across, or stay below the door.
3. It is forbidden to use the remote control when you can not see the door running, avoid accidents and misuse of the garage door opening.
4. The mechanical limiters should add the doors two side to prevent the body slid off the door.
   Note :If you do not have the side door ,please must installation blackouts unlocking device so as to open the door by hand when blackout.

Tools needed
During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.

Technical parameter

Install the Header Bracket and the door brac

Attach the Rail to the Header Bracket

Door arm connection

1. Close the door. Disconnect the trolley by pulling the emergency release handle.

2. Attach the straight door arm to the outer trolley using the Shouldered shaft, short (H6).
   Attach with the Cotter Pin (H5).

3.  Attach the curved door arm to the door bracket using the Shouldered shaft, short (H6). Attach with the Cotter Pin (H5).

4. Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity and attach using the bolts (H4) and nuts (H3).

5. Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal. The trolley will re-engage automatically when the garage door opener is activated.

Control Box—Overview

| ST

Enter Function Setup Menu Confirm chosen function or value

---|---
PR

In Standby : Enter Transmitter Setup Menu

OP

In Setup Menus: Scroll Function

CL

In Setup Menus: Scroll Function

Basic function settings

1    Adjusting the Open and Close Limits

| Press ‘ST’ button and hold on until the LED displays ‘1’.

Press and hold the ‘OP’ button, until the door reaches the desired open position.

NOTE: Fine adjustments can be made by toggling OP &CL buttons.

Press the ‘ST’ button     The LED displays ‘2’.

 | Press and hold the ‘CL‘ button until the door reaches the desired close position. For fine adjustments toggle OP &CL buttons.

Press the ‘ST’ button to confirm the close position. The door is now set for normal operation.

---|---
2   Programming Hand Transmitters
| |  | NOTE: Hand transmitters that are supplied with the door opener is pre-programmed.

Press and hold the PR button until the LED displays ‘   ’.

Now press the button on the hand transmitter you want to use, pause for 1 second, then press the same button on the hand transmitter again for 1 second. The LED will flash to confirm the

code, then turn off.

3    Deleting Stored Hand Transmitters
**| | | Press PR button until the LED displays   ’,**

Keep pressing the button, the LED is off, All stored remotes will be deleted.

Advanced function settings

1    Time to close

| Press ‘OP’ button and hold on until the LED

displays ‘    ’. Press the OP &CL buttons to select closing time.

Level| 0| 1| 2| 3| 4| 5|
Value| 0| 1minute| 2| 3| 4| 5
Level| 6| 7| 8| 9| –| –
Value| 6| 7| 8| 9| –| –

Press the ‘ST’ button to confirm it.

2 Safety Photo Beam
| Press ‘CL’ button and hold on until the LED displays ‘    ’. Press the’ OP orCL ‘buttons to open or close the function.

open the function ST

close the function PR CL

Press the ‘ST’ button to confirm it.

External Interface

Backup battery

References

• China Sliding Gate Operator Kit, Swing Gate Operator Kit, Sectional Door Operator Kit Factory - GATEXPERT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>