HYUNDAI 56433 Dual Temperature Heat Gun Instruction Manual

POWER PRODUCTS
MUURFREES 56433
Instruction manual

Declaration of conformity

56433 Dual Temperature Heat Gun

|
---|---

WALL CHASER 56433

WARNING
**** Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

SAFETY WARNINGS

When using the machine, always observe the enclosed safety warnings as well as the additional safety instructions below.

ADDITIONAL SAFETY INSTRUCTIONS FOR WALL CHASERS

• Do not use any other accessories than cutting discs.
• Make sure that the speed stated on the cutting disc is larger than or the same as the speed of the wall chaser given on the nameplate.
• Do not cut workpieces requiring a maximum depth of cut exceeding that of the cutting disc.
• Make sure that the cutting disc has the correct dimensions and fits properly on the spindle.
• Check the cutting disc before every use. Do not use cracked or otherwise damaged cutting discs.
• Make sure that the cutting discs are mounted in accordance with the instructions.
• After mounting the cutting discs let the machine run at no load speed in a safe area. If the machine vibrates strongly or if you see any damage to the cutting disc, switch off the machine immediately and try to establish the cause.
• Do not use adapters or other aids to mount cutting discs with a different spindle diameter.
• Make sure that sparks cannot hit any person or set flammable materials alight.
• Never reach into the cutting discs while the engine is running.
• Never work towards your body.
• Always wear safety goggles, hearing protection, and, if necessary, other protective means, such as working gloves, coat, hard hat, etc.
• Mount the screening guard. Never use the machine without a screening guard fitted.
• Beware that the cutting disc continues to rotate for a short period after switching off the tool.

Kickback and corresponding precautions
Kickback is the sudden reaction from a blocked cutting disc. Blocking leads to the sudden stopping of the rotating disc. This causes an uncontrolled electric tool to accelerate in a direction counter to the rotational direction of the disc. If, for example, a cutting disc cuts into the workpiece or blocks it, the edge of the cutting disc that digs into the workpiece can get caught and, through that, break off the cutting disc or cause a kickback. The cutting disc then moves towards or away from the operator, depending on the direction of rotation of the disc at the blocked spot. Here, the cutting discs can also break. A kickback is caused by wrongly or incorrectly operating the electric tool. It can be avoided by suitable cautionary measures, such as those described below.
Hold the electric tool very firmly and bring your body and your arm into a position in which you can resist the kickback force. Always use the supplemental handle if available to give you the best control over kickback force or reaction time during acceleration. The operator can master the kickback and reaction force through suitable precautions.
Never bring your hands near a rotating attachment tool. The attachment tool can run over your hand in the kickback.
Keep your body away from the area in which the electric tool would move during a kickback. The kickback drives the electric tool in the counter direction to the rotation of the cutting disc at the blocked spot.
Work particularly cautiously in corner areas or where there are sharp corners etc. Prevent the attachment tools from recoiling from the workpiece and jamming.
The rotating attachment tool tends to jam when near corners, sharp edges or when it recoils from such. This causes a loss of control or kickback.
Do not use chain or toothed cutting discs. Such attachment tools frequently cause a kickback or loss of control over the electric tool.
Avoid blocking the cutting disc or pressing down too hard. Do not make any excessively deep cuts. Overloading the cutting disc increases wear and its tendency to tilt or block and, with that, to kickback or break the grinder.
If the cutting disc jams, or you interrupt your work, switch the device off and hold it until the disc has come to a full stop. Never try to pull the cutting disc out of the cut while it is still running, because it can kick back. Identify and correct the cause of the jamming.
Do not switch the electric tool on again as long as it is in the workpiece. Allow the cutting disc to first reach its full rotational speed before you carefully resume with the cutting. Otherwise, the disc may catch, spring away from the workpiece or cause a kickback.
Be particularly careful for pocket cuts in existing walls or other areas where you cannot see what is there. The cutting disc may cause a kickback when it cuts into gas or water lines, electrical lines or other hidden objects.

WARNING
During operation, this electric tool generates an electromagnetic field which, under certain circumstances, may impair the functionality of active or passive medical implants. To reduce the risk of serious or lethal injuries, we recommend that persons with medical implants consult their doctor and the manufacturer of their medical implant before operating the machine.

Personal safety

| Wear safety goggles.
---|---
Wear hearing protection.
Wear a dust mask.
Wear work gloves.
Protection class II – double insulated.

The following symbols are used throughout this manual:
Denotes risk of personal injury or damage to the machine.
Denotes important information concerning the use of the machine.
ELECTRICAL SAFETY
Always check that the power supply corresponds to the voltage on the rating plate.
DESCRIPTION (FIG. A)
Your wall chaser has been designed for grinding and cutting masonry.

Package contents

• Wall chaser
• 5 cutting discs
• 4 flanges
• Carbon brush (1 pair)
• Flange key (1 pc)
• Wrench (1 pc)
• Storage case
• Instruction manual
• Safety Instructions
• Guarantee and service conditions

BEFORE USE

Mounting cutting discs (Fig. B-E)
Always switch off and unplug the tool before mounting.

1. Open the cover (11) by turning the wing nut (12).

2. Turn cover (13) to reach locking screw (14).

3. Loosen the locking screw with the flange key (14) and remove the locking screw (15).

4. Place the first cutting disc (16) on the mounting spindle (17), followed by a mounting flange (18).
   Then place the second disc and the second flange.

5. Place the remaining three cutting discs and two mounting flanges on the spindle.

6. Insert the locking screw (15) onto the spindle (16). Pay attention to the correct positioning.

7. Tighten the locking screw (15) with the flange key.

USE

Setting the cutting depth (Fig. F)

1. Adjust the plate (19) to control the grinding depth. The depth can be set between 30 and 40 mm.
2. Loosen the knob (20) and turn the plate until it reaches the desired depth.

Switching on and off

• To switch on the machine, press the on/off switch (3).
• To switch off the machine, release the on/off switch.

Instructions for use

The cutting direction should always be opposite to the disc’s rotational direction. Otherwise, the wall chaser can be pushed outside the cutting area in an uncontrolled manner.

1. Switch on the wall chaser.

2. Position the baffle plate (8) against the wall.

3. Bring the cutting discs into contact with the wall und start creating slots.

4. Move the machine along the surface.
   Guide the machine at a constant speed across the material to be worked. Do not force.

5. Once you reach the end of the groove, remove the machine from the groove before switching it off.

6. Chip out the resulting ridge between the grooves using a hand chisel (not included).

Dust extraction
The dust extraction outlet (1) together with an external vacuum cleaner takes care of the dust extraction of the working surface.

CLEANING AND MAINTENANCE

Always remove the plug from the socket before cleaning or performing maintenance work.
Let the device cool down before performing any maintenance or cleaning. There is a risk of burns.

Cleaning

• Do not use any cleaning agent or solvent. Chemical substances can etch the plastic parts of the device. Never clean the device under running water.

• Thoroughly clean the device after every use.

• Clean the ventilation openings and the surface of the device with a soft brush or cloth.

• Do not use brushes made of metal or the like to remove dust and avoid damaging the internal parts.
  Maintenance
  Maintenance should be performed by authorized personnel in order to prevent serious hazards.
  Always switch off and unplug the tool before maintenance.

• Always check the device before using it for obvious deficiencies such as loose, worn or damaged parts. Exchange the damaged parts.

• If the power cord needs to be replaced, it has to be done by an authorized service company.

TECHNICAL DATA

Noise and vibrations

Wear hearing protection.

GUARANTEE
Refer to the enclosed guarantee conditions for the terms and conditions of the guarantee.

ENVIRONMENT
Your product, accessories and packaging should be sorted for environmental- friendly recycling.
Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.
Subject to change; specifications can be changed without further notice.

……………

VERKLARING VAN OVEREENSTEMMING DECLARATION OF CONFORMITY
ART. NR. HYUNDAI 56433 TYPE NR. JHS-3200
Wall chaser that this product is in conformity with the following standards or standardization documents:
EN 60745-1:2009+A11:2010, EN 60745-2-22:2011+A11:2013, EN 55014-1:2017+A11:2020,
EN 55014-2:2015, EN IEC 61000-3-2:2019, EN 61000-3-3:2013+A1:2019
According to the provisions of the directives:2006/42/EC, 2014/30/EU
Testing authority: LCIE China Co., Ltd., Shanghai, China
Keeper of the technical documentation:

Device bv
Witte Vlinderweg 51,1521 PS Wormerveer, Nederland
info@dvize.eu,
www.hyundaitools-nl.com
Dvize bv Witte Vlinderweg 51
1521 PS Wormerveer
info@dvize.eu
Nederland
www.hyundaitools-nl.com
Imported/Distributed by Dvize bv, The Netherlands
Licensed by Hyundai Corporation, Korea

References

• Hyundai Power Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>