Secura V-470 Automatic Liquid Soap Dispenser User Manual
- June 16, 2024
- SECURA
Table of Contents
Secura V-470 Automatic Liquid Soap Dispenser
Features
- Spout
- Infrared sensor sender
- Battery compartment
- On/Off Switch & Liquid Soap Volume Control
- Container lid
Technical Data
- Dimension: L155W85H220mm/L6.1W3.3H8.7 in
- Vol: 500ml/16.9 oz.
- Liquid dosage: 1.0~5.5ml/0.03~0.19 oz.
- Unit weight: 420g/0.9 lb.
- Plastic material: ABS, PC
- Battery type: 1.5V “AA” alkaline
- Rated volt: DC6V
- Static current: 60uA
- Work current: 250mA
- Sensor range: 0~7cm/0~2.75 in.
Installation
- Insert 4 “AA” batteries into the battery compartment according to the diagram in the battery compartment.
- Open the container lid. (Figure 2)
- Fill with liquid soap. (Figure 3)
- Turn the On/Off switch to “On” and adjust the soap volume control to the middle of its setting.
- Put your hand under the sensor within 0~2.75 in to let the dispenser start to work. (For first time use, repeat this process several times until the soap begins to dispense). (Figure 4)
Liquid Soap Volume Control
- The volume of liquid soap dispensed can be adjusted from 0.03~0.19 oz. by rotating the On/Off switch.
- Rotating the On/Off switch towards the bottom of the dispenser will increase the amount of soap dispensed. Rotating it in the opposite direction will decreasee the amount of soap dispensed.
If Dispenser Doesn’t Work
- Make sure the batteries are placed in the battery compartment correctly and that they are fresh.
- Check that the On/Off switch has been switched to the “On” position.
If Soap is not Dispensed
- If this is the first use of the dispenser, place your hand under the sensor (within 0~2.75 in) several times until the soap begins to flow out of the spout.
- The liquid soap could become congealed in the spout or dispensing tube due to lack of use of the dispenser or cold/dry weather. If that is the case, pour out any soap remaining in the container, fill the container with warm soapy water and then operate the dispenser several times until the water begins to dispense from the spout. Pour out any remaining soapy water and refill the container with liquid soap.
Attention
- Place the dispenser on a flat, level surface.
- If wall mounting, do not install the dispenser above a mirrored surface or close to running water, as this might cause it to activate unnecessarily.
- This product is for indoor use. Exposure to direct sunlight will destroy the sensor system.
- Use liquid soap with a low concentration of alcohol.
- Avoid placing this product in areas where it could become covered in water.
- Keep the liquid clean.
- If you will not be using the dispenser for an extended period of time, empty the container of soap, clean the dispenser out and remove the batteries. Store it in a dry place.
- Do not subject the On/Off switch to too much exposure to water.
Cleaning
- Clean the dispenser’s surface with wet towel, battery compartment with dry towel.
Secura Inc.
- Tel: 888-792-2360
- CustomerCare@thesecura.com Brookfi eld, Wisconsin.USA
- www.thesecura.com
© 2016 SECURA INC.
TROUBLESHOOTING
- Power Source Verification: Ensure the dispenser has fresh and correctly placed 4 AA alkaline batteries.
- Battery Polarity Check: Confirm correct battery insertion with the right polarity.
- Battery Charge Confirmation: If using rechargeable batteries, guarantee they are adequately charged.
- Power Switch Position: Verify the ON/OFF switch is in the correct position.
- Sensor Calibration Inspection: Clean the sensor, checking for any obstructions, and adjust sensitivity as necessary.
- Soap Reservoir Examination: Confirm the reservoir is filled with suitable liquid soap.
- Soap Thickness Adjustment: Dilute thicker or moisturizing soaps with warm water or alcohol to prevent clogging.
- Feed Tube Inspection: Check for any soap residue or blockages in the feed tube.
- Dispensing Volume Verification: Adjust volume control to ensure the dispenser dispenses the correct amount of soap (0.03~0.19 oz.).
- Proper Positioning Assurance: Confirm the dispenser is correctly positioned and unobstructed.
- Infrared Interference Avoidance: Prevent placement in direct sunlight or near strong light sources to avoid infrared sensor interference.
- Sensor Range Validation: Ensure the sensor detects hands within the specified range (up to 2.75 inches).
- Container Seal Examination: Check for leaks or improper sealing in the soap container.
- Correct Container Placement Confirmation: Verify the soap container is correctly positioned within the dispenser.
- Regular Cleaning Practice: Clean the dispenser regularly, especially the sensor and dispensing area, to prevent buildup.
- Soap Compatibility Confirmation: Confirm the soap used is compatible with the dispenser.
- Resetting Procedure: Turn off the dispenser, wait briefly, and then turn it back on to reset.
- Firmware/Software Updates Check: Verify if there are any available updates for the dispenser’s firmware or software.
FREQUENTLY ASKED QUESTIONS
What is the brand of the automatic liquid soap dispenser with model number V-470?
The soap dispenser is from the brand Secura.
What material is used to make the Secura V-470 Automatic Liquid Soap Dispenser?
The dispenser is made of Plastic.
Can you provide the product dimensions of the Secura V-470 Automatic Liquid Soap Dispenser?
The product dimensions are 6 L x 3.3 W x 8.7 H Inches.
What is the shape of the Secura V-470 Automatic Liquid Soap Dispenser?
The dispenser has a hand shape.
How much does the Secura V-470 Automatic Liquid Soap Dispenser weigh?
The weight of the soap dispenser is 14.4 ounces.
What is the item model number of the Secura V-470 Automatic Liquid Soap Dispenser?
The item model number is V-470.
What type of batteries does the Secura V-470 Automatic Liquid Soap Dispenser require, and how many?
The dispenser requires 4 AA batteries (alkaline). Batteries are not included.
What is the capacity of the soap container in the Secura V-470 Automatic Liquid Soap Dispenser?
The dispenser has a 17 oz. capacity container.
Does the Secura V-470 Automatic Liquid Soap Dispenser have an ON/OFF switch?
Yes, it includes an ON/OFF switch for convenience.
Is there an adjustable volume control switch on the Secura V-470 Automatic Liquid Soap Dispenser?
Yes, the dispenser features an adjustable soap dispenser volume control switch to dispense 0.03~0.19 oz. per activation.
What is the finish of the Secura V-470 Automatic Liquid Soap Dispenser?
It has an attractive and stylish high-quality chrome and black finish.
Can the Secura V-470 Automatic Liquid Soap Dispenser be wall-mounted?
Yes, the dispenser can be wall-mounted or placed on a countertop.
How does the infrared sensor in the Secura V-470 Automatic Liquid Soap Dispenser work?
The infrared sensor detects your hand from as far away as 2.75 inches.
What type of operation does the Secura V-470 Automatic Liquid Soap Dispenser provide?
It provides touchless operation for easy and hygienic soap dispensing.
Is the Secura V-470 Automatic Liquid Soap Dispenser suitable for commercial use?
Yes, it is suitable for both commercial and household use.
VIDEO – PRODUCT OVERVIEW
DOWNLOAD THE PDF LINK: Secura V-470 Automatic Liquid Soap Dispenser User Manual
REFERENCE:Secura V-470 Automatic Liquid Soap Dispenser User Manual- Device.Report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>