iHome iSB04 DOOR/WINDOW SENSOR Quick Start Guide

iHome iSB04 DOOR WINDOW SENSOR

Wi-Fi DOOR/WINDOW SENSOR

Monitor your home from anywhere with your smartphone

WHAT YOU’LL NEED

• WiFi network transmitting at 2.4GHz; WPA2 security type
• Apple device running iOS 9.3 or later or Android device running KitKat 4.4 or later connected to your preferred WiFi network

NOTE: If you intend to use a mix of devices (iOS AND Android), please set up the Sensor using your iOS device and then share to your Android device(s).

Questions?

• 1.800.288.2792
• www.ihome.com

Overview: About Your Door/Window Sensor

What’s in the Box

• iSB04 Door/Window Sensor (main body and magnet)
• Adhesive Mounting Strip (see page 4 for mounting instructions)
• 2 AA batteries (see page 2 for battery installation instructions)

Sensor Overview

Wi-Fi Status Indicators

Installing Batteries

Your sensor comes with 2 AA alkaline batteries which must be installed before use. We recommend alkaline batteries only in this sensor.

1. Gently pull the front of the sensor forward using the battery access tab on top of the sensor to release the front of the main unit.
2. Place the batteries in the battery compartment as shown. Make sure polarity (+/–) matches the markings in the product.
3. Press the front and back cabinet together.

Wi-Fi Setup

NOTE: We recommend performing setup in the same location you intend to place your sensor.

1. Download and open the iHome Control app from the App Store or Google Play.  Login to or create an iHome account
2. Press sensors icon and then the Add Device Button.
3. Select your sensor, then tap “Next”.
4. Press and hold the Action Button on your sensor for 5 seconds until green LED is flashing, then release.
5. Enter the following setup code when prompted in the app.

NOTE: If you see a solid or flashing RED LED, press and hold the Action Button for 5 seconds and then repeat steps 2 and 3

Sensor Mounting

• The main sensor body includes mounting tape. A separate strip of tape is provided to mount the magnet.
• The strip of tape can be applied to the side OR top of the magnet body, whichever works best for your particular setup.

“The two hand test”

(Perform this test before mounting your sensor).

1. Use one hand to position the main sensor body against the intended mounting surface (we recommend a flat surface such as the door itself).
2. Use another hand to position the magnet body on the intended mounting surface.
3. Pull the sensor body away from the magnet to simulate opening the door/window.
4. If you hear 2 beeps your proposed mounting location is GOOD and you can proceed to mount your sensor with the adhesive tape. If no sound is heard you must try an alternate positioning.
5. Ensure the door/window can open/close freely without interfering with your sensor. Peel back the adhesive strip and press sensor against the surface for 60 seconds to ensure a good bond.

NOTE: Tape should be adhered to a clean/dry surface. We strongly recommend wiping surface with a 50/50 mixture of rubbing alcohol and water to allow for the strongest bond.

Sensor Placement Suggestions

Doors

Windows

*Mounting options are not limited to the suggestions in these images

Meet the iHome Control family of Intelligent Home solutions

iHome Control provides 24-7 remote home monitoring from anywhere. The free iHome Control app keeps you aware of changes in your home environment even when you’re not home. For information about compatible products and to purchase Sensors and SmartPlugs, visit iHome.com.

Notices

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.

To assure continued FCC compliance:

1. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

GENERAL BATTERY PRECAUTIONS

• Never use or charge a battery if it appears to be leaking, discolored, deformed, or in any way abnormal.
• Do not mix old and new batteries, and do not mix alkaline, carbon-zinc or rechargeable nickel-cadmium batteries
• Use only new batteries of the type recommended
• Avoid charging a rechargeable battery when the temperature is not within 5°C – 35°C (41° – 95° Fahrenheit).
• Never expose a battery to any liquid.
• Never expose a battery to excessive heat such as direct sunlight or fire. Never use a battery pack in an unventilated vehicle where excessive internal temperatures may be encountered.
• Always keep batteries out of the reach of infants and small children.
• Remove batteries if device will not be used for a prolonged period to avoid corrosion which can damage the unit
• Dispose of batteries that are leaking
• spose of batteries in accordance with local regulations

For warranty information: visit https://www.ihomeaudio.com/support/

FAQs

What brand is the iSB04 Door/Window Sensor?

The sensor is manufactured by the iHome brand.

What color is the iSB04 sensor?

The iSB04 sensor is available in white color.

How is the iSB04 sensor powered?

It is powered using batteries.

What is the weight of the iHome iSB04 Door/Window Sensor?

The sensor weighs 0.2 pounds or 3.2 ounces.

How far can the iSB04 sensor communicate or detect?

The maximum range for the sensor is 12 meters.

What is the primary use of the iSB04 sensor?

The iSB04 sensor is designed to detect leaks in your home and provide instant alerts, thereby helping to avoid costly damage and repairs.

How is the design of the iSB04 sensor unique?

It features a unique battery-powered Wi-Fi design that allows for discrete placement and mounting. It also has a dual sensor probe, which is like having two leak sensors in one.

Where can I place the iSB04 sensor in my home?

The sensor can be placed near sinks, toilets, hot water heaters, washing machines, and other potential leak sources.

How many batteries does the sensor require and are they included?

The iSB04 requires 2 AA alkaline batteries, which are included in the package.

Is the sensor designed for both indoor and outdoor use?

The iSB04 sensor is intended for indoor use only.

What components are included in the package?

The package includes the iSB04 Door/Window sensor.

Is the iSB04 Door/Window sensor still being manufactured?

No, the product is not discontinued by the manufacturer.

Download This PDF Link:iHome iSB04 DOOR WINDOW SENSOR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>